Temperature singleton class
This commit is contained in:
Scott Lahteine
parent
142bd3f3e7
commit
084f6b5b44
@ -340,10 +340,6 @@ extern int16_t code_value_short();
|
||||
extern uint8_t host_keepalive_interval;
|
||||
#endif
|
||||
|
||||
#if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
|
||||
extern float extrude_min_temp;
|
||||
#endif
|
||||
|
||||
#if FAN_COUNT > 0
|
||||
extern int fanSpeeds[FAN_COUNT];
|
||||
#endif
|
||||
|
||||
@ -544,10 +544,6 @@ static void report_current_position();
|
||||
}
|
||||
#endif
|
||||
|
||||
#if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
|
||||
float extrude_min_temp = EXTRUDE_MINTEMP;
|
||||
#endif
|
||||
|
||||
#if ENABLED(SDSUPPORT)
|
||||
#include "SdFatUtil.h"
|
||||
int freeMemory() { return SdFatUtil::FreeRam(); }
|
||||
@ -816,7 +812,7 @@ void setup() {
|
||||
|
||||
lcd_init();
|
||||
|
||||
tp_init(); // Initialize temperature loop
|
||||
thermalManager.init(); // Initialize temperature loop
|
||||
|
||||
#if ENABLED(DELTA) || ENABLED(SCARA)
|
||||
// Vital to init kinematic equivalent for X0 Y0 Z0
|
||||
@ -3839,7 +3835,7 @@ inline void gcode_M31() {
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLN(time);
|
||||
lcd_setstatus(time);
|
||||
autotempShutdown();
|
||||
thermalManager.autotempShutdown();
|
||||
}
|
||||
|
||||
#if ENABLED(SDSUPPORT)
|
||||
@ -4274,10 +4270,10 @@ inline void gcode_M104() {
|
||||
|
||||
if (code_seen('S')) {
|
||||
float temp = code_value();
|
||||
setTargetHotend(temp, target_extruder);
|
||||
thermalManager.setTargetHotend(temp, target_extruder);
|
||||
#if ENABLED(DUAL_X_CARRIAGE)
|
||||
if (dual_x_carriage_mode == DXC_DUPLICATION_MODE && target_extruder == 0)
|
||||
setTargetHotend1(temp == 0.0 ? 0.0 : temp + duplicate_extruder_temp_offset);
|
||||
thermalManager.setTargetHotend(temp == 0.0 ? 0.0 : temp + duplicate_extruder_temp_offset, 1);
|
||||
#endif
|
||||
|
||||
/**
|
||||
@ -4296,7 +4292,7 @@ inline void gcode_M104() {
|
||||
*/
|
||||
else print_job_timer.start();
|
||||
|
||||
if (temp > degHotend(target_extruder)) LCD_MESSAGEPGM(MSG_HEATING);
|
||||
if (temp > thermalManager.degHotend(target_extruder)) LCD_MESSAGEPGM(MSG_HEATING);
|
||||
}
|
||||
}
|
||||
|
||||
@ -4305,41 +4301,41 @@ inline void gcode_M104() {
|
||||
void print_heaterstates() {
|
||||
#if HAS_TEMP_HOTEND
|
||||
SERIAL_PROTOCOLPGM(" T:");
|
||||
SERIAL_PROTOCOL_F(degHotend(target_extruder), 1);
|
||||
SERIAL_PROTOCOL_F(thermalManager.degHotend(target_extruder), 1);
|
||||
SERIAL_PROTOCOLPGM(" /");
|
||||
SERIAL_PROTOCOL_F(degTargetHotend(target_extruder), 1);
|
||||
SERIAL_PROTOCOL_F(thermalManager.degTargetHotend(target_extruder), 1);
|
||||
#endif
|
||||
#if HAS_TEMP_BED
|
||||
SERIAL_PROTOCOLPGM(" B:");
|
||||
SERIAL_PROTOCOL_F(degBed(), 1);
|
||||
SERIAL_PROTOCOL_F(thermalManager.degBed(), 1);
|
||||
SERIAL_PROTOCOLPGM(" /");
|
||||
SERIAL_PROTOCOL_F(degTargetBed(), 1);
|
||||
SERIAL_PROTOCOL_F(thermalManager.degTargetBed(), 1);
|
||||
#endif
|
||||
#if EXTRUDERS > 1
|
||||
for (int8_t e = 0; e < EXTRUDERS; ++e) {
|
||||
SERIAL_PROTOCOLPGM(" T");
|
||||
SERIAL_PROTOCOL(e);
|
||||
SERIAL_PROTOCOLCHAR(':');
|
||||
SERIAL_PROTOCOL_F(degHotend(e), 1);
|
||||
SERIAL_PROTOCOL_F(thermalManager.degHotend(e), 1);
|
||||
SERIAL_PROTOCOLPGM(" /");
|
||||
SERIAL_PROTOCOL_F(degTargetHotend(e), 1);
|
||||
SERIAL_PROTOCOL_F(thermalManager.degTargetHotend(e), 1);
|
||||
}
|
||||
#endif
|
||||
#if HAS_TEMP_BED
|
||||
SERIAL_PROTOCOLPGM(" B@:");
|
||||
#ifdef BED_WATTS
|
||||
SERIAL_PROTOCOL(((BED_WATTS) * getHeaterPower(-1)) / 127);
|
||||
SERIAL_PROTOCOL(((BED_WATTS) * thermalManager.getHeaterPower(-1)) / 127);
|
||||
SERIAL_PROTOCOLCHAR('W');
|
||||
#else
|
||||
SERIAL_PROTOCOL(getHeaterPower(-1));
|
||||
SERIAL_PROTOCOL(thermalManager.getHeaterPower(-1));
|
||||
#endif
|
||||
#endif
|
||||
SERIAL_PROTOCOLPGM(" @:");
|
||||
#ifdef EXTRUDER_WATTS
|
||||
SERIAL_PROTOCOL(((EXTRUDER_WATTS) * getHeaterPower(target_extruder)) / 127);
|
||||
SERIAL_PROTOCOL(((EXTRUDER_WATTS) * thermalManager.getHeaterPower(target_extruder)) / 127);
|
||||
SERIAL_PROTOCOLCHAR('W');
|
||||
#else
|
||||
SERIAL_PROTOCOL(getHeaterPower(target_extruder));
|
||||
SERIAL_PROTOCOL(thermalManager.getHeaterPower(target_extruder));
|
||||
#endif
|
||||
#if EXTRUDERS > 1
|
||||
for (int8_t e = 0; e < EXTRUDERS; ++e) {
|
||||
@ -4347,27 +4343,27 @@ inline void gcode_M104() {
|
||||
SERIAL_PROTOCOL(e);
|
||||
SERIAL_PROTOCOLCHAR(':');
|
||||
#ifdef EXTRUDER_WATTS
|
||||
SERIAL_PROTOCOL(((EXTRUDER_WATTS) * getHeaterPower(e)) / 127);
|
||||
SERIAL_PROTOCOL(((EXTRUDER_WATTS) * thermalManager.getHeaterPower(e)) / 127);
|
||||
SERIAL_PROTOCOLCHAR('W');
|
||||
#else
|
||||
SERIAL_PROTOCOL(getHeaterPower(e));
|
||||
SERIAL_PROTOCOL(thermalManager.getHeaterPower(e));
|
||||
#endif
|
||||
}
|
||||
#endif
|
||||
#if ENABLED(SHOW_TEMP_ADC_VALUES)
|
||||
#if HAS_TEMP_BED
|
||||
SERIAL_PROTOCOLPGM(" ADC B:");
|
||||
SERIAL_PROTOCOL_F(degBed(), 1);
|
||||
SERIAL_PROTOCOL_F(thermalManager.degBed(), 1);
|
||||
SERIAL_PROTOCOLPGM("C->");
|
||||
SERIAL_PROTOCOL_F(rawBedTemp() / OVERSAMPLENR, 0);
|
||||
SERIAL_PROTOCOL_F(thermalManager.rawBedTemp() / OVERSAMPLENR, 0);
|
||||
#endif
|
||||
for (int8_t cur_extruder = 0; cur_extruder < EXTRUDERS; ++cur_extruder) {
|
||||
SERIAL_PROTOCOLPGM(" T");
|
||||
SERIAL_PROTOCOL(cur_extruder);
|
||||
SERIAL_PROTOCOLCHAR(':');
|
||||
SERIAL_PROTOCOL_F(degHotend(cur_extruder), 1);
|
||||
SERIAL_PROTOCOL_F(thermalManager.degHotend(cur_extruder), 1);
|
||||
SERIAL_PROTOCOLPGM("C->");
|
||||
SERIAL_PROTOCOL_F(rawHotendTemp(cur_extruder) / OVERSAMPLENR, 0);
|
||||
SERIAL_PROTOCOL_F(thermalManager.rawHotendTemp(cur_extruder) / OVERSAMPLENR, 0);
|
||||
}
|
||||
#endif
|
||||
}
|
||||
@ -4427,10 +4423,10 @@ inline void gcode_M109() {
|
||||
bool no_wait_for_cooling = code_seen('S');
|
||||
if (no_wait_for_cooling || code_seen('R')) {
|
||||
float temp = code_value();
|
||||
setTargetHotend(temp, target_extruder);
|
||||
thermalManager.setTargetHotend(temp, target_extruder);
|
||||
#if ENABLED(DUAL_X_CARRIAGE)
|
||||
if (dual_x_carriage_mode == DXC_DUPLICATION_MODE && target_extruder == 0)
|
||||
setTargetHotend1(temp == 0.0 ? 0.0 : temp + duplicate_extruder_temp_offset);
|
||||
thermalManager.setTargetHotend(temp == 0.0 ? 0.0 : temp + duplicate_extruder_temp_offset, 1);
|
||||
#endif
|
||||
|
||||
/**
|
||||
@ -4449,7 +4445,7 @@ inline void gcode_M109() {
|
||||
*/
|
||||
else print_job_timer.start();
|
||||
|
||||
if (temp > degHotend(target_extruder)) LCD_MESSAGEPGM(MSG_HEATING);
|
||||
if (temp > thermalManager.degHotend(target_extruder)) LCD_MESSAGEPGM(MSG_HEATING);
|
||||
}
|
||||
|
||||
#if ENABLED(AUTOTEMP)
|
||||
@ -4462,7 +4458,7 @@ inline void gcode_M109() {
|
||||
#define TEMP_CONDITIONS (!residency_start_ms || PENDING(now, residency_start_ms + (TEMP_RESIDENCY_TIME) * 1000UL))
|
||||
#else
|
||||
// Loop until the temperature is very close target
|
||||
#define TEMP_CONDITIONS (wants_to_cool ? isCoolingHotend(target_extruder) : isHeatingHotend(target_extruder))
|
||||
#define TEMP_CONDITIONS (wants_to_cool ? thermalManager.isCoolingHotend(target_extruder) : thermalManager.isHeatingHotend(target_extruder))
|
||||
#endif //TEMP_RESIDENCY_TIME > 0
|
||||
|
||||
float theTarget = -1;
|
||||
@ -4473,7 +4469,6 @@ inline void gcode_M109() {
|
||||
KEEPALIVE_STATE(NOT_BUSY);
|
||||
|
||||
do {
|
||||
|
||||
now = millis();
|
||||
if (ELAPSED(now, next_temp_ms)) { //Print temp & remaining time every 1s while waiting
|
||||
next_temp_ms = now + 1000UL;
|
||||
@ -4495,9 +4490,9 @@ inline void gcode_M109() {
|
||||
}
|
||||
|
||||
// Target temperature might be changed during the loop
|
||||
if (theTarget != degTargetHotend(target_extruder)) {
|
||||
theTarget = degTargetHotend(target_extruder);
|
||||
wants_to_cool = isCoolingHotend(target_extruder);
|
||||
if (theTarget != thermalManager.degTargetHotend(target_extruder)) {
|
||||
wants_to_cool = thermalManager.isCoolingHotend(target_extruder);
|
||||
theTarget = thermalManager.degTargetHotend(target_extruder);
|
||||
|
||||
// Exit if S<lower>, continue if S<higher>, R<lower>, or R<higher>
|
||||
if (no_wait_for_cooling && wants_to_cool) break;
|
||||
@ -4512,7 +4507,7 @@ inline void gcode_M109() {
|
||||
|
||||
#if TEMP_RESIDENCY_TIME > 0
|
||||
|
||||
float temp_diff = fabs(theTarget - degHotend(target_extruder));
|
||||
float temp_diff = fabs(theTarget - thermalManager.degHotend(target_extruder));
|
||||
|
||||
if (!residency_start_ms) {
|
||||
// Start the TEMP_RESIDENCY_TIME timer when we reach target temp for the first time.
|
||||
@ -4542,7 +4537,7 @@ inline void gcode_M109() {
|
||||
|
||||
LCD_MESSAGEPGM(MSG_BED_HEATING);
|
||||
bool no_wait_for_cooling = code_seen('S');
|
||||
if (no_wait_for_cooling || code_seen('R')) setTargetBed(code_value());
|
||||
if (no_wait_for_cooling || code_seen('R')) thermalManager.setTargetBed(code_value());
|
||||
|
||||
#if TEMP_BED_RESIDENCY_TIME > 0
|
||||
millis_t residency_start_ms = 0;
|
||||
@ -4550,7 +4545,7 @@ inline void gcode_M109() {
|
||||
#define TEMP_BED_CONDITIONS (!residency_start_ms || PENDING(now, residency_start_ms + (TEMP_BED_RESIDENCY_TIME) * 1000UL))
|
||||
#else
|
||||
// Loop until the temperature is very close target
|
||||
#define TEMP_BED_CONDITIONS (wants_to_cool ? isCoolingBed() : isHeatingBed())
|
||||
#define TEMP_BED_CONDITIONS (wants_to_cool ? thermalManager.isCoolingBed() : thermalManager.isHeatingBed())
|
||||
#endif //TEMP_BED_RESIDENCY_TIME > 0
|
||||
|
||||
float theTarget = -1;
|
||||
@ -4580,16 +4575,16 @@ inline void gcode_M109() {
|
||||
}
|
||||
|
||||
// Target temperature might be changed during the loop
|
||||
if (theTarget != degTargetBed()) {
|
||||
theTarget = degTargetBed();
|
||||
wants_to_cool = isCoolingBed();
|
||||
if (theTarget != thermalManager.degTargetBed()) {
|
||||
wants_to_cool = thermalManager.isCoolingBed();
|
||||
theTarget = thermalManager.degTargetBed();
|
||||
|
||||
// Exit if S<lower>, continue if S<higher>, R<lower>, or R<higher>
|
||||
if (no_wait_for_cooling && wants_to_cool) break;
|
||||
|
||||
// Prevent a wait-forever situation if R is misused i.e. M190 R0
|
||||
// Simply don't wait for cooling below 30C
|
||||
if (wants_to_cool && theTarget < (EXTRUDE_MINTEMP)/2) break;
|
||||
// Simply don't wait to cool a bed under 30C
|
||||
if (wants_to_cool && theTarget < 30) break;
|
||||
}
|
||||
|
||||
idle();
|
||||
@ -4597,7 +4592,7 @@ inline void gcode_M109() {
|
||||
|
||||
#if TEMP_BED_RESIDENCY_TIME > 0
|
||||
|
||||
float temp_diff = fabs(degBed() - degTargetBed());
|
||||
float temp_diff = fabs(theTarget - thermalManager.degBed());
|
||||
|
||||
if (!residency_start_ms) {
|
||||
// Start the TEMP_BED_RESIDENCY_TIME timer when we reach target temp for the first time.
|
||||
@ -4720,7 +4715,7 @@ inline void gcode_M112() { kill(PSTR(MSG_KILLED)); }
|
||||
*/
|
||||
inline void gcode_M140() {
|
||||
if (DEBUGGING(DRYRUN)) return;
|
||||
if (code_seen('S')) setTargetBed(code_value());
|
||||
if (code_seen('S')) thermalManager.setTargetBed(code_value());
|
||||
}
|
||||
|
||||
#if ENABLED(ULTIPANEL)
|
||||
@ -4811,7 +4806,7 @@ inline void gcode_M140() {
|
||||
* This code should ALWAYS be available for EMERGENCY SHUTDOWN!
|
||||
*/
|
||||
inline void gcode_M81() {
|
||||
disable_all_heaters();
|
||||
thermalManager.disable_all_heaters();
|
||||
stepper.finish_and_disable();
|
||||
#if FAN_COUNT > 0
|
||||
#if FAN_COUNT > 1
|
||||
@ -5469,7 +5464,7 @@ inline void gcode_M226() {
|
||||
NOMORE(lpq_len, LPQ_MAX_LEN);
|
||||
#endif
|
||||
|
||||
updatePID();
|
||||
thermalManager.updatePID();
|
||||
SERIAL_ECHO_START;
|
||||
#if ENABLED(PID_PARAMS_PER_EXTRUDER)
|
||||
SERIAL_ECHO(" e:"); // specify extruder in serial output
|
||||
@ -5499,18 +5494,19 @@ inline void gcode_M226() {
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
inline void gcode_M304() {
|
||||
if (code_seen('P')) bedKp = code_value();
|
||||
if (code_seen('I')) bedKi = scalePID_i(code_value());
|
||||
if (code_seen('D')) bedKd = scalePID_d(code_value());
|
||||
if (code_seen('P')) thermalManager.bedKp = code_value();
|
||||
if (code_seen('I')) thermalManager.bedKi = scalePID_i(code_value());
|
||||
if (code_seen('D')) thermalManager.bedKd = scalePID_d(code_value());
|
||||
|
||||
thermalManager.updatePID();
|
||||
|
||||
updatePID();
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHO(" p:");
|
||||
SERIAL_ECHO(bedKp);
|
||||
SERIAL_ECHO(thermalManager.bedKp);
|
||||
SERIAL_ECHO(" i:");
|
||||
SERIAL_ECHO(unscalePID_i(bedKi));
|
||||
SERIAL_ECHO(unscalePID_i(thermalManager.bedKi));
|
||||
SERIAL_ECHO(" d:");
|
||||
SERIAL_ECHOLN(unscalePID_d(bedKd));
|
||||
SERIAL_ECHOLN(unscalePID_d(thermalManager.bedKd));
|
||||
}
|
||||
|
||||
#endif // PIDTEMPBED
|
||||
@ -5567,13 +5563,11 @@ inline void gcode_M226() {
|
||||
|
||||
#if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
|
||||
|
||||
void set_extrude_min_temp(float temp) { extrude_min_temp = temp; }
|
||||
|
||||
/**
|
||||
* M302: Allow cold extrudes, or set the minimum extrude S<temperature>.
|
||||
*/
|
||||
inline void gcode_M302() {
|
||||
set_extrude_min_temp(code_seen('S') ? code_value() : 0);
|
||||
thermalManager.extrude_min_temp = code_seen('S') ? code_value() : 0;
|
||||
}
|
||||
|
||||
#endif // PREVENT_DANGEROUS_EXTRUDE
|
||||
@ -5599,7 +5593,7 @@ inline void gcode_M303() {
|
||||
|
||||
KEEPALIVE_STATE(NOT_BUSY); // don't send "busy: processing" messages during autotune output
|
||||
|
||||
PID_autotune(temp, e, c, u);
|
||||
thermalManager.PID_autotune(temp, e, c, u);
|
||||
|
||||
KEEPALIVE_STATE(IN_HANDLER);
|
||||
#else
|
||||
@ -5781,7 +5775,7 @@ inline void gcode_M400() { stepper.synchronize(); }
|
||||
NOMORE(meas_delay_cm, MAX_MEASUREMENT_DELAY);
|
||||
|
||||
if (filwidth_delay_index2 == -1) { // Initialize the ring buffer if not done since startup
|
||||
int temp_ratio = widthFil_to_size_ratio();
|
||||
int temp_ratio = thermalManager.widthFil_to_size_ratio();
|
||||
|
||||
for (uint8_t i = 0; i < COUNT(measurement_delay); ++i)
|
||||
measurement_delay[i] = temp_ratio - 100; // Subtract 100 to scale within a signed byte
|
||||
@ -5984,7 +5978,7 @@ inline void gcode_M503() {
|
||||
*/
|
||||
inline void gcode_M600() {
|
||||
|
||||
if (degHotend(active_extruder) < extrude_min_temp) {
|
||||
if (thermalManager.tooColdToExtrude(active_extruder)) {
|
||||
SERIAL_ERROR_START;
|
||||
SERIAL_ERRORLNPGM(MSG_TOO_COLD_FOR_M600);
|
||||
return;
|
||||
@ -7268,7 +7262,7 @@ void mesh_buffer_line(float x, float y, float z, const float e, float feed_rate,
|
||||
if (DEBUGGING(DRYRUN)) return;
|
||||
float de = dest_e - curr_e;
|
||||
if (de) {
|
||||
if (degHotend(active_extruder) < extrude_min_temp) {
|
||||
if (thermalManager.tooColdToExtrude(active_extruder)) {
|
||||
curr_e = dest_e; // Behave as if the move really took place, but ignore E part
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLNPGM(MSG_ERR_COLD_EXTRUDE_STOP);
|
||||
@ -7565,7 +7559,7 @@ void plan_arc(
|
||||
millis_t ms = millis();
|
||||
if (ELAPSED(ms, nextMotorCheck)) {
|
||||
nextMotorCheck = ms + 2500UL; // Not a time critical function, so only check every 2.5s
|
||||
if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON || soft_pwm_bed > 0
|
||||
if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON || thermalManager.soft_pwm_bed > 0
|
||||
|| E0_ENABLE_READ == E_ENABLE_ON // If any of the drivers are enabled...
|
||||
#if EXTRUDERS > 1
|
||||
|| E1_ENABLE_READ == E_ENABLE_ON
|
||||
@ -7683,9 +7677,9 @@ void plan_arc(
|
||||
if (ELAPSED(millis(), next_status_led_update_ms)) {
|
||||
next_status_led_update_ms += 500; // Update every 0.5s
|
||||
for (int8_t cur_extruder = 0; cur_extruder < EXTRUDERS; ++cur_extruder)
|
||||
max_temp = max(max(max_temp, degHotend(cur_extruder)), degTargetHotend(cur_extruder));
|
||||
max_temp = max(max(max_temp, thermalManager.degHotend(cur_extruder)), thermalManager.degTargetHotend(cur_extruder));
|
||||
#if HAS_TEMP_BED
|
||||
max_temp = max(max(max_temp, degTargetBed()), degBed());
|
||||
max_temp = max(max(max_temp, thermalManager.degTargetBed()), thermalManager.degBed());
|
||||
#endif
|
||||
bool new_led = (max_temp > 55.0) ? true : (max_temp < 54.0) ? false : red_led;
|
||||
if (new_led != red_led) {
|
||||
@ -7726,7 +7720,7 @@ void idle(
|
||||
bool no_stepper_sleep/*=false*/
|
||||
#endif
|
||||
) {
|
||||
manage_heater();
|
||||
thermalManager.manage_heater();
|
||||
manage_inactivity(
|
||||
#if ENABLED(FILAMENTCHANGEENABLE)
|
||||
no_stepper_sleep
|
||||
@ -7831,7 +7825,7 @@ void manage_inactivity(bool ignore_stepper_queue/*=false*/) {
|
||||
|
||||
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
|
||||
if (ELAPSED(ms, previous_cmd_ms + (EXTRUDER_RUNOUT_SECONDS) * 1000UL))
|
||||
if (degHotend(active_extruder) > EXTRUDER_RUNOUT_MINTEMP) {
|
||||
if (thermalManager.degHotend(active_extruder) > EXTRUDER_RUNOUT_MINTEMP) {
|
||||
bool oldstatus;
|
||||
switch (active_extruder) {
|
||||
case 0:
|
||||
@ -7914,7 +7908,7 @@ void kill(const char* lcd_msg) {
|
||||
#endif
|
||||
|
||||
cli(); // Stop interrupts
|
||||
disable_all_heaters();
|
||||
thermalManager.disable_all_heaters();
|
||||
disable_all_steppers();
|
||||
|
||||
#if HAS_POWER_SWITCH
|
||||
@ -8010,7 +8004,7 @@ void kill(const char* lcd_msg) {
|
||||
#endif // FAST_PWM_FAN
|
||||
|
||||
void stop() {
|
||||
disable_all_heaters();
|
||||
thermalManager.disable_all_heaters();
|
||||
if (IsRunning()) {
|
||||
Running = false;
|
||||
Stopped_gcode_LastN = gcode_LastN; // Save last g_code for restart
|
||||
|
||||
@ -609,7 +609,7 @@ void CardReader::printingHasFinished() {
|
||||
sdprinting = false;
|
||||
if (SD_FINISHED_STEPPERRELEASE)
|
||||
enqueue_and_echo_commands_P(PSTR(SD_FINISHED_RELEASECOMMAND));
|
||||
autotempShutdown();
|
||||
thermalManager.autotempShutdown();
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
@ -95,7 +95,7 @@
|
||||
* 363 M301 L lpq_len (int)
|
||||
*
|
||||
* PIDTEMPBED:
|
||||
* 365 M304 PID bedKp, bedKi, bedKd (float x3)
|
||||
* 365 M304 PID thermalManager.bedKp, thermalManager.bedKi, thermalManager.bedKd (float x3)
|
||||
*
|
||||
* DOGLCD:
|
||||
* 377 M250 C lcd_contrast (int)
|
||||
@ -261,9 +261,9 @@ void Config_StoreSettings() {
|
||||
#endif // !PIDTEMP
|
||||
{
|
||||
dummy = DUMMY_PID_VALUE; // When read, will not change the existing value
|
||||
EEPROM_WRITE_VAR(i, dummy);
|
||||
EEPROM_WRITE_VAR(i, dummy); // Kp
|
||||
dummy = 0.0f;
|
||||
for (uint8_t q = 3; q--;) EEPROM_WRITE_VAR(i, dummy);
|
||||
for (uint8_t q = 3; q--;) EEPROM_WRITE_VAR(i, dummy); // Ki, Kd, Kc
|
||||
}
|
||||
|
||||
} // Extruders Loop
|
||||
@ -274,13 +274,14 @@ void Config_StoreSettings() {
|
||||
EEPROM_WRITE_VAR(i, lpq_len);
|
||||
|
||||
#if DISABLED(PIDTEMPBED)
|
||||
float bedKp = DUMMY_PID_VALUE, bedKi = DUMMY_PID_VALUE, bedKd = DUMMY_PID_VALUE;
|
||||
dummy = DUMMY_PID_VALUE;
|
||||
for (uint8_t q = 3; q--;) EEPROM_WRITE_VAR(i, dummy);
|
||||
#else
|
||||
EEPROM_WRITE_VAR(i, thermalManager.bedKp);
|
||||
EEPROM_WRITE_VAR(i, thermalManager.bedKi);
|
||||
EEPROM_WRITE_VAR(i, thermalManager.bedKd);
|
||||
#endif
|
||||
|
||||
EEPROM_WRITE_VAR(i, bedKp);
|
||||
EEPROM_WRITE_VAR(i, bedKi);
|
||||
EEPROM_WRITE_VAR(i, bedKd);
|
||||
|
||||
#if DISABLED(HAS_LCD_CONTRAST)
|
||||
const int lcd_contrast = 32;
|
||||
#endif
|
||||
@ -450,19 +451,16 @@ void Config_RetrieveSettings() {
|
||||
#endif
|
||||
EEPROM_READ_VAR(i, lpq_len);
|
||||
|
||||
#if DISABLED(PIDTEMPBED)
|
||||
float bedKp, bedKi, bedKd;
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
EEPROM_READ_VAR(i, dummy); // bedKp
|
||||
if (dummy != DUMMY_PID_VALUE) {
|
||||
bedKp = dummy; UNUSED(bedKp);
|
||||
EEPROM_READ_VAR(i, bedKi);
|
||||
EEPROM_READ_VAR(i, bedKd);
|
||||
}
|
||||
else {
|
||||
for (uint8_t q=2; q--;) EEPROM_READ_VAR(i, dummy); // bedKi, bedKd
|
||||
thermalManager.bedKp = dummy;
|
||||
EEPROM_READ_VAR(i, thermalManager.bedKi);
|
||||
EEPROM_READ_VAR(i, thermalManager.bedKd);
|
||||
}
|
||||
#else
|
||||
for (uint8_t q=3; q--;) EEPROM_READ_VAR(i, dummy); // bedKp, bedKi, bedKd
|
||||
#endif
|
||||
|
||||
#if DISABLED(HAS_LCD_CONTRAST)
|
||||
int lcd_contrast;
|
||||
@ -502,8 +500,8 @@ void Config_RetrieveSettings() {
|
||||
}
|
||||
|
||||
calculate_volumetric_multipliers();
|
||||
// Call updatePID (similar to when we have processed M301)
|
||||
updatePID();
|
||||
// Call thermalManager.updatePID (similar to when we have processed M301)
|
||||
thermalManager.updatePID();
|
||||
|
||||
// Report settings retrieved and length
|
||||
SERIAL_ECHO_START;
|
||||
@ -602,14 +600,14 @@ void Config_ResetDefault() {
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
lpq_len = 20; // default last-position-queue size
|
||||
#endif
|
||||
// call updatePID (similar to when we have processed M301)
|
||||
updatePID();
|
||||
// call thermalManager.updatePID (similar to when we have processed M301)
|
||||
thermalManager.updatePID();
|
||||
#endif // PIDTEMP
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
bedKp = DEFAULT_bedKp;
|
||||
bedKi = scalePID_i(DEFAULT_bedKi);
|
||||
bedKd = scalePID_d(DEFAULT_bedKd);
|
||||
thermalManager.bedKp = DEFAULT_bedKp;
|
||||
thermalManager.bedKi = scalePID_i(DEFAULT_bedKi);
|
||||
thermalManager.bedKd = scalePID_d(DEFAULT_bedKd);
|
||||
#endif
|
||||
|
||||
#if ENABLED(FWRETRACT)
|
||||
@ -835,9 +833,9 @@ void Config_PrintSettings(bool forReplay) {
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
CONFIG_ECHO_START;
|
||||
SERIAL_ECHOPAIR(" M304 P", bedKp);
|
||||
SERIAL_ECHOPAIR(" I", unscalePID_i(bedKi));
|
||||
SERIAL_ECHOPAIR(" D", unscalePID_d(bedKd));
|
||||
SERIAL_ECHOPAIR(" M304 P", thermalManager.bedKp);
|
||||
SERIAL_ECHOPAIR(" I", unscalePID_i(thermalManager.bedKi));
|
||||
SERIAL_ECHOPAIR(" D", unscalePID_d(thermalManager.bedKd));
|
||||
SERIAL_EOL;
|
||||
#endif
|
||||
|
||||
|
||||
@ -294,13 +294,13 @@ FORCE_INLINE void _draw_heater_status(int x, int heater) {
|
||||
const bool isBed = false;
|
||||
#endif
|
||||
|
||||
_draw_centered_temp((isBed ? degTargetBed() : degTargetHotend(heater)) + 0.5, x, 7);
|
||||
_draw_centered_temp((isBed ? thermalManager.degTargetBed() : thermalManager.degTargetHotend(heater)) + 0.5, x, 7);
|
||||
|
||||
_draw_centered_temp((isBed ? degBed() : degHotend(heater)) + 0.5, x, 28);
|
||||
_draw_centered_temp((isBed ? thermalManager.degBed() : thermalManager.degHotend(heater)) + 0.5, x, 28);
|
||||
|
||||
int h = isBed ? 7 : 8,
|
||||
y = isBed ? 18 : 17;
|
||||
if (isBed ? isHeatingBed() : isHeatingHotend(heater)) {
|
||||
if (isBed ? thermalManager.isHeatingBed() : thermalManager.isHeatingHotend(heater)) {
|
||||
u8g.setColorIndex(0); // white on black
|
||||
u8g.drawBox(x + h, y, 2, 2);
|
||||
u8g.setColorIndex(1); // black on white
|
||||
|
||||
@ -153,7 +153,7 @@ void Endstops::report_state() {
|
||||
card.sdprinting = false;
|
||||
card.closefile();
|
||||
stepper.quick_stop();
|
||||
disable_all_heaters(); // switch off all heaters.
|
||||
thermalManager.disable_all_heaters(); // switch off all heaters.
|
||||
}
|
||||
#endif
|
||||
}
|
||||
|
||||
@ -304,7 +304,7 @@ void Planner::recalculate() {
|
||||
static float oldt = 0;
|
||||
|
||||
if (!autotemp_enabled) return;
|
||||
if (degTargetHotend0() + 2 < autotemp_min) return; // probably temperature set to zero.
|
||||
if (thermalManager.degTargetHotend(0) + 2 < autotemp_min) return; // probably temperature set to zero.
|
||||
|
||||
float high = 0.0;
|
||||
for (uint8_t b = block_buffer_tail; b != block_buffer_head; b = next_block_index(b)) {
|
||||
@ -322,7 +322,7 @@ void Planner::recalculate() {
|
||||
t += (AUTOTEMP_OLDWEIGHT) * oldt;
|
||||
}
|
||||
oldt = t;
|
||||
setTargetHotend0(t);
|
||||
thermalManager.setTargetHotend(t, 0);
|
||||
}
|
||||
|
||||
#endif //AUTOTEMP
|
||||
@ -489,11 +489,12 @@ void Planner::check_axes_activity() {
|
||||
// The target position of the tool in absolute steps
|
||||
// Calculate target position in absolute steps
|
||||
//this should be done after the wait, because otherwise a M92 code within the gcode disrupts this calculation somehow
|
||||
long target[NUM_AXIS];
|
||||
target[X_AXIS] = lround(x * axis_steps_per_unit[X_AXIS]);
|
||||
target[Y_AXIS] = lround(y * axis_steps_per_unit[Y_AXIS]);
|
||||
target[Z_AXIS] = lround(z * axis_steps_per_unit[Z_AXIS]);
|
||||
target[E_AXIS] = lround(e * axis_steps_per_unit[E_AXIS]);
|
||||
long target[NUM_AXIS] = {
|
||||
lround(x * axis_steps_per_unit[X_AXIS]),
|
||||
lround(y * axis_steps_per_unit[Y_AXIS]),
|
||||
lround(z * axis_steps_per_unit[Z_AXIS]),
|
||||
lround(e * axis_steps_per_unit[E_AXIS])
|
||||
};
|
||||
|
||||
long dx = target[X_AXIS] - position[X_AXIS],
|
||||
dy = target[Y_AXIS] - position[Y_AXIS],
|
||||
@ -507,7 +508,7 @@ void Planner::check_axes_activity() {
|
||||
|
||||
#if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
|
||||
if (de) {
|
||||
if (degHotend(extruder) < extrude_min_temp) {
|
||||
if (thermalManager.tooColdToExtrude(extruder)) {
|
||||
position[E_AXIS] = target[E_AXIS]; // Behave as if the move really took place, but ignore E part
|
||||
de = 0; // no difference
|
||||
SERIAL_ECHO_START;
|
||||
@ -788,7 +789,7 @@ void Planner::check_axes_activity() {
|
||||
// If the index has changed (must have gone forward)...
|
||||
if (filwidth_delay_index1 != filwidth_delay_index2) {
|
||||
filwidth_e_count = 0; // Reset the E movement counter
|
||||
int8_t meas_sample = widthFil_to_size_ratio() - 100; // Subtract 100 to reduce magnitude - to store in a signed char
|
||||
int8_t meas_sample = thermalManager.widthFil_to_size_ratio() - 100; // Subtract 100 to reduce magnitude - to store in a signed char
|
||||
do {
|
||||
filwidth_delay_index2 = (filwidth_delay_index2 + 1) % MMD_CM; // The next unused slot
|
||||
measurement_delay[filwidth_delay_index2] = meas_sample; // Store the measurement
|
||||
|
||||
@ -21,23 +21,7 @@
|
||||
*/
|
||||
|
||||
/**
|
||||
temperature.cpp - temperature control
|
||||
Part of Marlin
|
||||
|
||||
Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 3 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
* temperature.cpp - temperature control
|
||||
*/
|
||||
|
||||
#include "Marlin.h"
|
||||
@ -50,144 +34,10 @@
|
||||
#include "watchdog.h"
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//================================== macros =================================
|
||||
//===========================================================================
|
||||
|
||||
#ifdef K1 // Defined in Configuration.h in the PID settings
|
||||
#define K2 (1.0-K1)
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMPBED) || ENABLED(PIDTEMP)
|
||||
#define PID_dT ((OVERSAMPLENR * 12.0)/(F_CPU / 64.0 / 256.0))
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//============================= public variables ============================
|
||||
//===========================================================================
|
||||
|
||||
int target_temperature[4] = { 0 };
|
||||
int target_temperature_bed = 0;
|
||||
int current_temperature_raw[4] = { 0 };
|
||||
float current_temperature[4] = { 0.0 };
|
||||
int current_temperature_bed_raw = 0;
|
||||
float current_temperature_bed = 0.0;
|
||||
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
|
||||
int redundant_temperature_raw = 0;
|
||||
float redundant_temperature = 0.0;
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
float bedKp = DEFAULT_bedKp;
|
||||
float bedKi = (DEFAULT_bedKi* PID_dT);
|
||||
float bedKd = (DEFAULT_bedKd / PID_dT);
|
||||
#endif //PIDTEMPBED
|
||||
|
||||
#if ENABLED(FAN_SOFT_PWM)
|
||||
unsigned char fanSpeedSoftPwm[FAN_COUNT];
|
||||
#endif
|
||||
|
||||
unsigned char soft_pwm_bed;
|
||||
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
volatile int babystepsTodo[3] = { 0 };
|
||||
#endif
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
int current_raw_filwidth = 0; //Holds measured filament diameter - one extruder only
|
||||
#endif
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS) || ENABLED(THERMAL_PROTECTION_BED)
|
||||
enum TRState { TRReset, TRInactive, TRFirstHeating, TRStable, TRRunaway };
|
||||
void thermal_runaway_protection(TRState* state, millis_t* timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc);
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
static TRState thermal_runaway_state_machine[4] = { TRReset, TRReset, TRReset, TRReset };
|
||||
static millis_t thermal_runaway_timer[4]; // = {0,0,0,0};
|
||||
#endif
|
||||
#if ENABLED(THERMAL_PROTECTION_BED) && TEMP_SENSOR_BED != 0
|
||||
static TRState thermal_runaway_bed_state_machine = TRReset;
|
||||
static millis_t thermal_runaway_bed_timer;
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//============================ private variables ============================
|
||||
//===========================================================================
|
||||
|
||||
static volatile bool temp_meas_ready = false;
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//static cannot be external:
|
||||
static float temp_iState[EXTRUDERS] = { 0 };
|
||||
static float temp_dState[EXTRUDERS] = { 0 };
|
||||
static float pTerm[EXTRUDERS];
|
||||
static float iTerm[EXTRUDERS];
|
||||
static float dTerm[EXTRUDERS];
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
static float cTerm[EXTRUDERS];
|
||||
static long last_position[EXTRUDERS];
|
||||
static long lpq[LPQ_MAX_LEN];
|
||||
static int lpq_ptr = 0;
|
||||
#endif
|
||||
//int output;
|
||||
static float pid_error[EXTRUDERS];
|
||||
static float temp_iState_min[EXTRUDERS];
|
||||
static float temp_iState_max[EXTRUDERS];
|
||||
static bool pid_reset[EXTRUDERS];
|
||||
#endif //PIDTEMP
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//static cannot be external:
|
||||
static float temp_iState_bed = { 0 };
|
||||
static float temp_dState_bed = { 0 };
|
||||
static float pTerm_bed;
|
||||
static float iTerm_bed;
|
||||
static float dTerm_bed;
|
||||
//int output;
|
||||
static float pid_error_bed;
|
||||
static float temp_iState_min_bed;
|
||||
static float temp_iState_max_bed;
|
||||
#else //PIDTEMPBED
|
||||
static millis_t next_bed_check_ms;
|
||||
#endif //PIDTEMPBED
|
||||
static unsigned char soft_pwm[EXTRUDERS];
|
||||
|
||||
#if ENABLED(FAN_SOFT_PWM)
|
||||
static unsigned char soft_pwm_fan[FAN_COUNT];
|
||||
#endif
|
||||
#if HAS_AUTO_FAN
|
||||
static millis_t next_auto_fan_check_ms;
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
#if ENABLED(PID_PARAMS_PER_EXTRUDER)
|
||||
float Kp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(DEFAULT_Kp);
|
||||
float Ki[EXTRUDERS] = ARRAY_BY_EXTRUDERS1((DEFAULT_Ki) * (PID_dT));
|
||||
float Kd[EXTRUDERS] = ARRAY_BY_EXTRUDERS1((DEFAULT_Kd) / (PID_dT));
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
float Kc[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(DEFAULT_Kc);
|
||||
#endif // PID_ADD_EXTRUSION_RATE
|
||||
#else //PID_PARAMS_PER_EXTRUDER
|
||||
float Kp = DEFAULT_Kp;
|
||||
float Ki = (DEFAULT_Ki) * (PID_dT);
|
||||
float Kd = (DEFAULT_Kd) / (PID_dT);
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
float Kc = DEFAULT_Kc;
|
||||
#endif // PID_ADD_EXTRUSION_RATE
|
||||
#endif // PID_PARAMS_PER_EXTRUDER
|
||||
#endif //PIDTEMP
|
||||
|
||||
// Init min and max temp with extreme values to prevent false errors during startup
|
||||
static int minttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_RAW_LO_TEMP , HEATER_1_RAW_LO_TEMP , HEATER_2_RAW_LO_TEMP, HEATER_3_RAW_LO_TEMP);
|
||||
static int maxttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_RAW_HI_TEMP , HEATER_1_RAW_HI_TEMP , HEATER_2_RAW_HI_TEMP, HEATER_3_RAW_HI_TEMP);
|
||||
static int minttemp[EXTRUDERS] = { 0 };
|
||||
static int maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(16383);
|
||||
#ifdef BED_MINTEMP
|
||||
static int bed_minttemp_raw = HEATER_BED_RAW_LO_TEMP;
|
||||
#endif
|
||||
#ifdef BED_MAXTEMP
|
||||
static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP;
|
||||
#endif
|
||||
|
||||
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
|
||||
static void* heater_ttbl_map[2] = {(void*)HEATER_0_TEMPTABLE, (void*)HEATER_1_TEMPTABLE };
|
||||
static uint8_t heater_ttbllen_map[2] = { HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN };
|
||||
@ -196,39 +46,11 @@ static int maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(16383);
|
||||
static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN, HEATER_3_TEMPTABLE_LEN);
|
||||
#endif
|
||||
|
||||
static float analog2temp(int raw, uint8_t e);
|
||||
static float analog2tempBed(int raw);
|
||||
static void updateTemperaturesFromRawValues();
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0
|
||||
int watch_target_temp[EXTRUDERS] = { 0 };
|
||||
millis_t watch_heater_next_ms[EXTRUDERS] = { 0 };
|
||||
#endif
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_BED) && WATCH_BED_TEMP_PERIOD > 0
|
||||
int watch_target_bed_temp = 0;
|
||||
millis_t watch_bed_next_ms = 0;
|
||||
#endif
|
||||
|
||||
#ifndef SOFT_PWM_SCALE
|
||||
#define SOFT_PWM_SCALE 0
|
||||
#endif
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
static int meas_shift_index; //used to point to a delayed sample in buffer for filament width sensor
|
||||
#endif
|
||||
|
||||
#if ENABLED(HEATER_0_USES_MAX6675)
|
||||
static int read_max6675();
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//================================ Functions ================================
|
||||
//===========================================================================
|
||||
Temperature thermalManager;
|
||||
|
||||
#if HAS_PID_HEATING
|
||||
|
||||
void PID_autotune(float temp, int extruder, int ncycles, bool set_result/*=false*/) {
|
||||
void Temperature::PID_autotune(float temp, int extruder, int ncycles, bool set_result/*=false*/) {
|
||||
float input = 0.0;
|
||||
int cycles = 0;
|
||||
bool heating = true;
|
||||
@ -242,7 +64,7 @@ static void updateTemperaturesFromRawValues();
|
||||
float max = 0, min = 10000;
|
||||
|
||||
#if HAS_AUTO_FAN
|
||||
millis_t next_auto_fan_check_ms = temp_ms + 2500UL;
|
||||
next_auto_fan_check_ms = temp_ms + 2500UL;
|
||||
#endif
|
||||
|
||||
if (false
|
||||
@ -459,9 +281,37 @@ static void updateTemperaturesFromRawValues();
|
||||
}
|
||||
}
|
||||
|
||||
#endif // PIDTEMP
|
||||
#endif // HAS_PID_HEATING
|
||||
|
||||
void updatePID() {
|
||||
#if ENABLED(PIDTEMP)
|
||||
|
||||
#if ENABLED(PID_PARAMS_PER_EXTRUDER)
|
||||
|
||||
float Temperature::Kp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(DEFAULT_Kp),
|
||||
Temperature::Ki[EXTRUDERS] = ARRAY_BY_EXTRUDERS1((DEFAULT_Ki) * (PID_dT)),
|
||||
Temperature::Kd[EXTRUDERS] = ARRAY_BY_EXTRUDERS1((DEFAULT_Kd) / (PID_dT));
|
||||
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
float Temperature::Kc[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(DEFAULT_Kc);
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
||||
float Temperature::Kp = DEFAULT_Kp,
|
||||
Temperature::Ki = (DEFAULT_Ki) * (PID_dT),
|
||||
Temperature::Kd = (DEFAULT_Kd) / (PID_dT);
|
||||
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
float Temperature::Kc = DEFAULT_Kc;
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
Temperature::Temperature() { }
|
||||
|
||||
void Temperature::updatePID() {
|
||||
#if ENABLED(PIDTEMP)
|
||||
for (int e = 0; e < EXTRUDERS; e++) {
|
||||
temp_iState_max[e] = (PID_INTEGRAL_DRIVE_MAX) / PID_PARAM(Ki, e);
|
||||
@ -475,77 +325,33 @@ void updatePID() {
|
||||
#endif
|
||||
}
|
||||
|
||||
int getHeaterPower(int heater) {
|
||||
int Temperature::getHeaterPower(int heater) {
|
||||
return heater < 0 ? soft_pwm_bed : soft_pwm[heater];
|
||||
}
|
||||
|
||||
#if HAS_AUTO_FAN
|
||||
|
||||
void setExtruderAutoFanState(int pin, bool state) {
|
||||
unsigned char newFanSpeed = (state != 0) ? EXTRUDER_AUTO_FAN_SPEED : 0;
|
||||
// this idiom allows both digital and PWM fan outputs (see M42 handling).
|
||||
digitalWrite(pin, newFanSpeed);
|
||||
analogWrite(pin, newFanSpeed);
|
||||
}
|
||||
|
||||
void checkExtruderAutoFans() {
|
||||
void Temperature::checkExtruderAutoFans() {
|
||||
const uint8_t fanPin[] = { EXTRUDER_0_AUTO_FAN_PIN, EXTRUDER_1_AUTO_FAN_PIN, EXTRUDER_2_AUTO_FAN_PIN, EXTRUDER_3_AUTO_FAN_PIN };
|
||||
const int fanBit[] = { 0,
|
||||
EXTRUDER_1_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN ? 0 : 1,
|
||||
EXTRUDER_2_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN ? 0 :
|
||||
EXTRUDER_2_AUTO_FAN_PIN == EXTRUDER_1_AUTO_FAN_PIN ? 1 : 2,
|
||||
EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN ? 0 :
|
||||
EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_1_AUTO_FAN_PIN ? 1 :
|
||||
EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_2_AUTO_FAN_PIN ? 2 : 3
|
||||
};
|
||||
uint8_t fanState = 0;
|
||||
|
||||
// which fan pins need to be turned on?
|
||||
#if HAS_AUTO_FAN_0
|
||||
if (current_temperature[0] > EXTRUDER_AUTO_FAN_TEMPERATURE)
|
||||
fanState |= 1;
|
||||
#endif
|
||||
#if HAS_AUTO_FAN_1
|
||||
if (current_temperature[1] > EXTRUDER_AUTO_FAN_TEMPERATURE) {
|
||||
if (EXTRUDER_1_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN)
|
||||
fanState |= 1;
|
||||
else
|
||||
fanState |= 2;
|
||||
for (int f = 0; f <= 3; f++) {
|
||||
if (current_temperature[f] > EXTRUDER_AUTO_FAN_TEMPERATURE)
|
||||
SBI(fanState, fanBit[f]);
|
||||
}
|
||||
#endif
|
||||
#if HAS_AUTO_FAN_2
|
||||
if (current_temperature[2] > EXTRUDER_AUTO_FAN_TEMPERATURE) {
|
||||
if (EXTRUDER_2_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN)
|
||||
fanState |= 1;
|
||||
else if (EXTRUDER_2_AUTO_FAN_PIN == EXTRUDER_1_AUTO_FAN_PIN)
|
||||
fanState |= 2;
|
||||
else
|
||||
fanState |= 4;
|
||||
for (int f = 0; f <= 3; f++) {
|
||||
unsigned char newFanSpeed = TEST(fanState, f) ? EXTRUDER_AUTO_FAN_SPEED : 0;
|
||||
// this idiom allows both digital and PWM fan outputs (see M42 handling).
|
||||
digitalWrite(fanPin[f], newFanSpeed);
|
||||
analogWrite(fanPin[f], newFanSpeed);
|
||||
}
|
||||
#endif
|
||||
#if HAS_AUTO_FAN_3
|
||||
if (current_temperature[3] > EXTRUDER_AUTO_FAN_TEMPERATURE) {
|
||||
if (EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN)
|
||||
fanState |= 1;
|
||||
else if (EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_1_AUTO_FAN_PIN)
|
||||
fanState |= 2;
|
||||
else if (EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_2_AUTO_FAN_PIN)
|
||||
fanState |= 4;
|
||||
else
|
||||
fanState |= 8;
|
||||
}
|
||||
#endif
|
||||
|
||||
// update extruder auto fan states
|
||||
#if HAS_AUTO_FAN_0
|
||||
setExtruderAutoFanState(EXTRUDER_0_AUTO_FAN_PIN, (fanState & 1) != 0);
|
||||
#endif
|
||||
#if HAS_AUTO_FAN_1
|
||||
if (EXTRUDER_1_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN)
|
||||
setExtruderAutoFanState(EXTRUDER_1_AUTO_FAN_PIN, (fanState & 2) != 0);
|
||||
#endif
|
||||
#if HAS_AUTO_FAN_2
|
||||
if (EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN
|
||||
&& EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN)
|
||||
setExtruderAutoFanState(EXTRUDER_2_AUTO_FAN_PIN, (fanState & 4) != 0);
|
||||
#endif
|
||||
#if HAS_AUTO_FAN_3
|
||||
if (EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN
|
||||
&& EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN
|
||||
&& EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_2_AUTO_FAN_PIN)
|
||||
setExtruderAutoFanState(EXTRUDER_3_AUTO_FAN_PIN, (fanState & 8) != 0);
|
||||
#endif
|
||||
}
|
||||
|
||||
#endif // HAS_AUTO_FAN
|
||||
@ -553,7 +359,7 @@ void checkExtruderAutoFans() {
|
||||
//
|
||||
// Temperature Error Handlers
|
||||
//
|
||||
inline void _temp_error(int e, const char* serial_msg, const char* lcd_msg) {
|
||||
void Temperature::_temp_error(int e, const char* serial_msg, const char* lcd_msg) {
|
||||
static bool killed = false;
|
||||
if (IsRunning()) {
|
||||
SERIAL_ERROR_START;
|
||||
@ -572,14 +378,14 @@ inline void _temp_error(int e, const char* serial_msg, const char* lcd_msg) {
|
||||
#endif
|
||||
}
|
||||
|
||||
void max_temp_error(uint8_t e) {
|
||||
void Temperature::max_temp_error(uint8_t e) {
|
||||
_temp_error(e, PSTR(MSG_T_MAXTEMP), PSTR(MSG_ERR_MAXTEMP));
|
||||
}
|
||||
void min_temp_error(uint8_t e) {
|
||||
void Temperature::min_temp_error(uint8_t e) {
|
||||
_temp_error(e, PSTR(MSG_T_MINTEMP), PSTR(MSG_ERR_MINTEMP));
|
||||
}
|
||||
|
||||
float get_pid_output(int e) {
|
||||
float Temperature::get_pid_output(int e) {
|
||||
float pid_output;
|
||||
#if ENABLED(PIDTEMP)
|
||||
#if DISABLED(PID_OPENLOOP)
|
||||
@ -658,7 +464,7 @@ float get_pid_output(int e) {
|
||||
}
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
float get_pid_output_bed() {
|
||||
float Temperature::get_pid_output_bed() {
|
||||
float pid_output;
|
||||
#if DISABLED(PID_OPENLOOP)
|
||||
pid_error_bed = target_temperature_bed - current_temperature_bed;
|
||||
@ -710,7 +516,7 @@ float get_pid_output(int e) {
|
||||
* - Apply filament width to the extrusion rate (may move)
|
||||
* - Update the heated bed PID output value
|
||||
*/
|
||||
void manage_heater() {
|
||||
void Temperature::manage_heater() {
|
||||
|
||||
if (!temp_meas_ready) return;
|
||||
|
||||
@ -811,7 +617,7 @@ void manage_heater() {
|
||||
|
||||
#if TEMP_SENSOR_BED != 0
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_BED)
|
||||
#if HAS_THERMALLY_PROTECTED_BED
|
||||
thermal_runaway_protection(&thermal_runaway_bed_state_machine, &thermal_runaway_bed_timer, current_temperature_bed, target_temperature_bed, -1, THERMAL_PROTECTION_BED_PERIOD, THERMAL_PROTECTION_BED_HYSTERESIS);
|
||||
#endif
|
||||
|
||||
@ -846,9 +652,10 @@ void manage_heater() {
|
||||
}
|
||||
|
||||
#define PGM_RD_W(x) (short)pgm_read_word(&x)
|
||||
|
||||
// Derived from RepRap FiveD extruder::getTemperature()
|
||||
// For hot end temperature measurement.
|
||||
static float analog2temp(int raw, uint8_t e) {
|
||||
float Temperature::analog2temp(int raw, uint8_t e) {
|
||||
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
|
||||
if (e > EXTRUDERS)
|
||||
#else
|
||||
@ -891,7 +698,7 @@ static float analog2temp(int raw, uint8_t e) {
|
||||
|
||||
// Derived from RepRap FiveD extruder::getTemperature()
|
||||
// For bed temperature measurement.
|
||||
static float analog2tempBed(int raw) {
|
||||
float Temperature::analog2tempBed(int raw) {
|
||||
#if ENABLED(BED_USES_THERMISTOR)
|
||||
float celsius = 0;
|
||||
byte i;
|
||||
@ -923,18 +730,22 @@ static float analog2tempBed(int raw) {
|
||||
#endif
|
||||
}
|
||||
|
||||
/* Called to get the raw values into the the actual temperatures. The raw values are created in interrupt context,
|
||||
and this function is called from normal context as it is too slow to run in interrupts and will block the stepper routine otherwise */
|
||||
static void updateTemperaturesFromRawValues() {
|
||||
/**
|
||||
* Get the raw values into the actual temperatures.
|
||||
* The raw values are created in interrupt context,
|
||||
* and this function is called from normal context
|
||||
* as it would block the stepper routine.
|
||||
*/
|
||||
void Temperature::updateTemperaturesFromRawValues() {
|
||||
#if ENABLED(HEATER_0_USES_MAX6675)
|
||||
current_temperature_raw[0] = read_max6675();
|
||||
#endif
|
||||
for (uint8_t e = 0; e < EXTRUDERS; e++) {
|
||||
current_temperature[e] = analog2temp(current_temperature_raw[e], e);
|
||||
current_temperature[e] = Temperature::analog2temp(current_temperature_raw[e], e);
|
||||
}
|
||||
current_temperature_bed = analog2tempBed(current_temperature_bed_raw);
|
||||
current_temperature_bed = Temperature::analog2tempBed(current_temperature_bed_raw);
|
||||
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
|
||||
redundant_temperature = analog2temp(redundant_temperature_raw, 1);
|
||||
redundant_temperature = Temperature::analog2temp(redundant_temperature_raw, 1);
|
||||
#endif
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
filament_width_meas = analog2widthFil();
|
||||
@ -954,13 +765,13 @@ static void updateTemperaturesFromRawValues() {
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
|
||||
// Convert raw Filament Width to millimeters
|
||||
float analog2widthFil() {
|
||||
float Temperature::analog2widthFil() {
|
||||
return current_raw_filwidth / 16383.0 * 5.0;
|
||||
//return current_raw_filwidth;
|
||||
}
|
||||
|
||||
// Convert raw Filament Width to a ratio
|
||||
int widthFil_to_size_ratio() {
|
||||
int Temperature::widthFil_to_size_ratio() {
|
||||
float temp = filament_width_meas;
|
||||
if (temp < MEASURED_LOWER_LIMIT) temp = filament_width_nominal; //assume sensor cut out
|
||||
else NOMORE(temp, MEASURED_UPPER_LIMIT);
|
||||
@ -974,7 +785,8 @@ static void updateTemperaturesFromRawValues() {
|
||||
* Initialize the temperature manager
|
||||
* The manager is implemented by periodic calls to manage_heater()
|
||||
*/
|
||||
void tp_init() {
|
||||
void Temperature::init() {
|
||||
|
||||
#if MB(RUMBA) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1))
|
||||
//disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector
|
||||
MCUCR = _BV(JTD);
|
||||
@ -1189,7 +1001,7 @@ void tp_init() {
|
||||
* their target temperature by a configurable margin.
|
||||
* This is called when the temperature is set. (M104, M109)
|
||||
*/
|
||||
void start_watching_heater(int e) {
|
||||
void Temperature::start_watching_heater(int e) {
|
||||
if (degHotend(e) < degTargetHotend(e) - (WATCH_TEMP_INCREASE + TEMP_HYSTERESIS + 1)) {
|
||||
watch_target_temp[e] = degHotend(e) + WATCH_TEMP_INCREASE;
|
||||
watch_heater_next_ms[e] = millis() + (WATCH_TEMP_PERIOD) * 1000UL;
|
||||
@ -1205,7 +1017,7 @@ void tp_init() {
|
||||
* their target temperature by a configurable margin.
|
||||
* This is called when the temperature is set. (M140, M190)
|
||||
*/
|
||||
void start_watching_bed() {
|
||||
void Temperature::start_watching_bed() {
|
||||
if (degBed() < degTargetBed() - (WATCH_BED_TEMP_INCREASE + TEMP_BED_HYSTERESIS + 1)) {
|
||||
watch_target_bed_temp = degBed() + WATCH_BED_TEMP_INCREASE;
|
||||
watch_bed_next_ms = millis() + (WATCH_BED_TEMP_PERIOD) * 1000UL;
|
||||
@ -1215,9 +1027,9 @@ void tp_init() {
|
||||
}
|
||||
#endif
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS) || ENABLED(THERMAL_PROTECTION_BED)
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED
|
||||
|
||||
void thermal_runaway_protection(TRState* state, millis_t* timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc) {
|
||||
void Temperature::thermal_runaway_protection(TRState* state, millis_t* timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc) {
|
||||
|
||||
static float tr_target_temperature[EXTRUDERS + 1] = { 0.0 };
|
||||
|
||||
@ -1273,7 +1085,7 @@ void tp_init() {
|
||||
|
||||
#endif // THERMAL_PROTECTION_HOTENDS || THERMAL_PROTECTION_BED
|
||||
|
||||
void disable_all_heaters() {
|
||||
void Temperature::disable_all_heaters() {
|
||||
for (int i = 0; i < EXTRUDERS; i++) setTargetHotend(0, i);
|
||||
setTargetBed(0);
|
||||
|
||||
@ -1327,9 +1139,9 @@ void disable_all_heaters() {
|
||||
#define MAX6675_DISCARD_BITS 3
|
||||
#endif
|
||||
|
||||
static millis_t next_max6675_ms = 0;
|
||||
int Temperature::read_max6675() {
|
||||
|
||||
static int read_max6675() {
|
||||
static millis_t next_max6675_ms = 0;
|
||||
|
||||
millis_t ms = millis();
|
||||
|
||||
@ -1392,10 +1204,10 @@ enum TempState {
|
||||
StartupDelay // Startup, delay initial temp reading a tiny bit so the hardware can settle
|
||||
};
|
||||
|
||||
static unsigned long raw_temp_value[4] = { 0 };
|
||||
static unsigned long raw_temp_bed_value = 0;
|
||||
|
||||
static void set_current_temp_raw() {
|
||||
/**
|
||||
* Get raw temperatures
|
||||
*/
|
||||
void Temperature::set_current_temp_raw() {
|
||||
#if HAS_TEMP_0 && DISABLED(HEATER_0_USES_MAX6675)
|
||||
current_temperature_raw[0] = raw_temp_value[0];
|
||||
#endif
|
||||
@ -1423,7 +1235,9 @@ static void set_current_temp_raw() {
|
||||
* - Check new temperature values for MIN/MAX errors
|
||||
* - Step the babysteps value for each axis towards 0
|
||||
*/
|
||||
ISR(TIMER0_COMPB_vect) {
|
||||
ISR(TIMER0_COMPB_vect) { thermalManager.isr(); }
|
||||
|
||||
void Temperature::isr() {
|
||||
|
||||
static unsigned char temp_count = 0;
|
||||
static TempState temp_state = StartupDelay;
|
||||
@ -1845,11 +1659,3 @@ ISR(TIMER0_COMPB_vect) {
|
||||
}
|
||||
#endif //BABYSTEPPING
|
||||
}
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
// Apply the scale factors to the PID values
|
||||
float scalePID_i(float i) { return i * PID_dT; }
|
||||
float unscalePID_i(float i) { return i / PID_dT; }
|
||||
float scalePID_d(float d) { return d / PID_dT; }
|
||||
float unscalePID_d(float d) { return d * PID_dT; }
|
||||
#endif //PIDTEMP
|
||||
|
||||
@ -21,23 +21,7 @@
|
||||
*/
|
||||
|
||||
/**
|
||||
temperature.h - temperature controller
|
||||
Part of Marlin
|
||||
|
||||
Copyright (c) 2011 Erik van der Zalm
|
||||
|
||||
Grbl is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 3 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
Grbl is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
||||
* temperature.h - temperature controller
|
||||
*/
|
||||
|
||||
#ifndef TEMPERATURE_H
|
||||
@ -45,74 +29,205 @@
|
||||
|
||||
#include "Marlin.h"
|
||||
#include "planner.h"
|
||||
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
#include "stepper.h"
|
||||
#endif
|
||||
|
||||
// public functions
|
||||
void tp_init(); //initialize the heating
|
||||
void manage_heater(); //it is critical that this is called periodically.
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
// For converting raw Filament Width to milimeters
|
||||
float analog2widthFil();
|
||||
|
||||
// For converting raw Filament Width to an extrusion ratio
|
||||
int widthFil_to_size_ratio();
|
||||
#ifndef SOFT_PWM_SCALE
|
||||
#define SOFT_PWM_SCALE 0
|
||||
#endif
|
||||
|
||||
// low level conversion routines
|
||||
// do not use these routines and variables outside of temperature.cpp
|
||||
extern int target_temperature[4];
|
||||
extern float current_temperature[4];
|
||||
#if ENABLED(SHOW_TEMP_ADC_VALUES)
|
||||
extern int current_temperature_raw[4];
|
||||
extern int current_temperature_bed_raw;
|
||||
#endif
|
||||
extern int target_temperature_bed;
|
||||
extern float current_temperature_bed;
|
||||
class Temperature {
|
||||
|
||||
public:
|
||||
|
||||
int current_temperature_raw[EXTRUDERS] = { 0 };
|
||||
float current_temperature[EXTRUDERS] = { 0.0 };
|
||||
int target_temperature[EXTRUDERS] = { 0 };
|
||||
|
||||
int current_temperature_bed_raw = 0;
|
||||
float current_temperature_bed = 0.0;
|
||||
int target_temperature_bed = 0;
|
||||
|
||||
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
|
||||
extern float redundant_temperature;
|
||||
float redundant_temperature = 0.0;
|
||||
#endif
|
||||
|
||||
#if HAS_CONTROLLERFAN
|
||||
extern unsigned char soft_pwm_bed;
|
||||
#endif
|
||||
unsigned char soft_pwm_bed;
|
||||
|
||||
#if ENABLED(FAN_SOFT_PWM)
|
||||
extern unsigned char fanSpeedSoftPwm[FAN_COUNT];
|
||||
unsigned char fanSpeedSoftPwm[FAN_COUNT];
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMP) || ENABLED(PIDTEMPBED)
|
||||
#define PID_dT ((OVERSAMPLENR * 12.0)/(F_CPU / 64.0 / 256.0))
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
|
||||
#if ENABLED(PID_PARAMS_PER_EXTRUDER)
|
||||
extern float Kp[EXTRUDERS], Ki[EXTRUDERS], Kd[EXTRUDERS]; // one param per extruder
|
||||
|
||||
static float Kp[EXTRUDERS], Ki[EXTRUDERS], Kd[EXTRUDERS];
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
extern float Kc[EXTRUDERS];
|
||||
float Kc[EXTRUDERS];
|
||||
#endif
|
||||
#define PID_PARAM(param, e) param[e] // use macro to point to array value
|
||||
#define PID_PARAM(param, e) Temperature::param[e]
|
||||
|
||||
#else
|
||||
extern float Kp, Ki, Kd; // one param per extruder - saves 20 or 36 bytes of ram (inc array pointer)
|
||||
|
||||
static float Kp, Ki, Kd;
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
extern float Kc;
|
||||
static float Kc;
|
||||
#endif
|
||||
#define PID_PARAM(param, e) param // use macro to point directly to value
|
||||
#define PID_PARAM(param, e) Temperature::param
|
||||
|
||||
#endif // PID_PARAMS_PER_EXTRUDER
|
||||
float scalePID_i(float i);
|
||||
float scalePID_d(float d);
|
||||
float unscalePID_i(float i);
|
||||
float unscalePID_d(float d);
|
||||
|
||||
// Apply the scale factors to the PID values
|
||||
#define scalePID_i(i) ( (i) * PID_dT )
|
||||
#define unscalePID_i(i) ( (i) / PID_dT )
|
||||
#define scalePID_d(d) ( (d) / PID_dT )
|
||||
#define unscalePID_d(d) ( (d) * PID_dT )
|
||||
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
extern float bedKp, bedKi, bedKd;
|
||||
float bedKp = DEFAULT_bedKp,
|
||||
bedKi = ((DEFAULT_bedKi) * PID_dT),
|
||||
bedKd = ((DEFAULT_bedKd) / PID_dT);
|
||||
#endif
|
||||
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
extern volatile int babystepsTodo[3];
|
||||
volatile int babystepsTodo[3] = { 0 };
|
||||
#endif
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0
|
||||
int watch_target_temp[EXTRUDERS] = { 0 };
|
||||
millis_t watch_heater_next_ms[EXTRUDERS] = { 0 };
|
||||
#endif
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_BED_TEMP_PERIOD > 0
|
||||
int watch_target_bed_temp = 0;
|
||||
millis_t watch_bed_next_ms = 0;
|
||||
#endif
|
||||
|
||||
#if ENABLED(PREVENT_DANGEROUS_EXTRUDE)
|
||||
float extrude_min_temp = EXTRUDE_MINTEMP;
|
||||
FORCE_INLINE bool tooColdToExtrude(uint8_t e) { return degHotend(e) < extrude_min_temp; }
|
||||
#else
|
||||
FORCE_INLINE bool tooColdToExtrude(uint8_t e) { UNUSED(e); return false; }
|
||||
#endif
|
||||
|
||||
private:
|
||||
|
||||
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
|
||||
int redundant_temperature_raw = 0;
|
||||
float redundant_temperature = 0.0;
|
||||
#endif
|
||||
|
||||
volatile bool temp_meas_ready = false;
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
float temp_iState[EXTRUDERS] = { 0 };
|
||||
float temp_dState[EXTRUDERS] = { 0 };
|
||||
float pTerm[EXTRUDERS];
|
||||
float iTerm[EXTRUDERS];
|
||||
float dTerm[EXTRUDERS];
|
||||
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
float cTerm[EXTRUDERS];
|
||||
long last_position[EXTRUDERS];
|
||||
long lpq[LPQ_MAX_LEN];
|
||||
int lpq_ptr = 0;
|
||||
#endif
|
||||
|
||||
float pid_error[EXTRUDERS];
|
||||
float temp_iState_min[EXTRUDERS];
|
||||
float temp_iState_max[EXTRUDERS];
|
||||
bool pid_reset[EXTRUDERS];
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
float temp_iState_bed = { 0 };
|
||||
float temp_dState_bed = { 0 };
|
||||
float pTerm_bed;
|
||||
float iTerm_bed;
|
||||
float dTerm_bed;
|
||||
float pid_error_bed;
|
||||
float temp_iState_min_bed;
|
||||
float temp_iState_max_bed;
|
||||
#else
|
||||
millis_t next_bed_check_ms;
|
||||
#endif
|
||||
|
||||
unsigned long raw_temp_value[4] = { 0 };
|
||||
unsigned long raw_temp_bed_value = 0;
|
||||
|
||||
// Init min and max temp with extreme values to prevent false errors during startup
|
||||
int minttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_RAW_LO_TEMP , HEATER_1_RAW_LO_TEMP , HEATER_2_RAW_LO_TEMP, HEATER_3_RAW_LO_TEMP);
|
||||
int maxttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_RAW_HI_TEMP , HEATER_1_RAW_HI_TEMP , HEATER_2_RAW_HI_TEMP, HEATER_3_RAW_HI_TEMP);
|
||||
int minttemp[EXTRUDERS] = { 0 };
|
||||
int maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(16383);
|
||||
|
||||
#ifdef BED_MINTEMP
|
||||
int bed_minttemp_raw = HEATER_BED_RAW_LO_TEMP;
|
||||
#endif
|
||||
|
||||
#ifdef BED_MAXTEMP
|
||||
int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP;
|
||||
#endif
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
int meas_shift_index; // Index of a delayed sample in buffer
|
||||
#endif
|
||||
|
||||
#if HAS_AUTO_FAN
|
||||
millis_t next_auto_fan_check_ms;
|
||||
#endif
|
||||
|
||||
unsigned char soft_pwm[EXTRUDERS];
|
||||
|
||||
#if ENABLED(FAN_SOFT_PWM)
|
||||
unsigned char soft_pwm_fan[FAN_COUNT];
|
||||
#endif
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
int current_raw_filwidth = 0; //Holds measured filament diameter - one extruder only
|
||||
#endif
|
||||
|
||||
public:
|
||||
|
||||
/**
|
||||
* Static (class) methods
|
||||
*/
|
||||
static float analog2temp(int raw, uint8_t e);
|
||||
static float analog2tempBed(int raw);
|
||||
|
||||
/**
|
||||
* Instance Methods
|
||||
*/
|
||||
|
||||
Temperature();
|
||||
|
||||
void init();
|
||||
|
||||
/**
|
||||
* Called from the Temperature ISR
|
||||
*/
|
||||
void isr();
|
||||
|
||||
/**
|
||||
* Call periodically to manage heaters
|
||||
*/
|
||||
void manage_heater();
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
float analog2widthFil(); // Convert raw Filament Width to millimeters
|
||||
int widthFil_to_size_ratio(); // Convert raw Filament Width to an extrusion ratio
|
||||
#endif
|
||||
|
||||
|
||||
//high level conversion routines, for use outside of temperature.cpp
|
||||
//inline so that there is no performance decrease.
|
||||
//deg=degreeCelsius
|
||||
@ -142,6 +257,7 @@ FORCE_INLINE void setTargetHotend(const float& celsius, uint8_t extruder) {
|
||||
start_watching_heater(extruder);
|
||||
#endif
|
||||
}
|
||||
|
||||
FORCE_INLINE void setTargetBed(const float& celsius) {
|
||||
target_temperature_bed = celsius;
|
||||
#if ENABLED(THERMAL_PROTECTION_BED) && WATCH_BED_TEMP_PERIOD > 0
|
||||
@ -155,39 +271,27 @@ FORCE_INLINE bool isHeatingBed() { return target_temperature_bed > current_tempe
|
||||
FORCE_INLINE bool isCoolingHotend(uint8_t extruder) { return target_temperature[extruder] < current_temperature[extruder]; }
|
||||
FORCE_INLINE bool isCoolingBed() { return target_temperature_bed < current_temperature_bed; }
|
||||
|
||||
#define HOTEND_ROUTINES(NR) \
|
||||
FORCE_INLINE float degHotend##NR() { return degHotend(NR); } \
|
||||
FORCE_INLINE float degTargetHotend##NR() { return degTargetHotend(NR); } \
|
||||
FORCE_INLINE void setTargetHotend##NR(const float c) { setTargetHotend(c, NR); } \
|
||||
FORCE_INLINE bool isHeatingHotend##NR() { return isHeatingHotend(NR); } \
|
||||
FORCE_INLINE bool isCoolingHotend##NR() { return isCoolingHotend(NR); }
|
||||
HOTEND_ROUTINES(0);
|
||||
#if EXTRUDERS > 1
|
||||
HOTEND_ROUTINES(1);
|
||||
#else
|
||||
#define setTargetHotend1(c) do{}while(0)
|
||||
#endif
|
||||
#if EXTRUDERS > 2
|
||||
HOTEND_ROUTINES(2);
|
||||
#else
|
||||
#define setTargetHotend2(c) do{}while(0)
|
||||
#endif
|
||||
#if EXTRUDERS > 3
|
||||
HOTEND_ROUTINES(3);
|
||||
#else
|
||||
#define setTargetHotend3(c) do{}while(0)
|
||||
#endif
|
||||
|
||||
/**
|
||||
* The software PWM power for a heater
|
||||
*/
|
||||
int getHeaterPower(int heater);
|
||||
void disable_all_heaters();
|
||||
void updatePID();
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
/**
|
||||
* Switch off all heaters, set all target temperatures to 0
|
||||
*/
|
||||
void disable_all_heaters();
|
||||
|
||||
/**
|
||||
* Perform auto-tuning for hotend or bed in response to M303
|
||||
*/
|
||||
#if HAS_PID_HEATING
|
||||
void PID_autotune(float temp, int extruder, int ncycles, bool set_result=false);
|
||||
#endif
|
||||
|
||||
void setExtruderAutoFanState(int pin, bool state);
|
||||
void checkExtruderAutoFans();
|
||||
/**
|
||||
* Update the temp manager when PID values change
|
||||
*/
|
||||
void updatePID();
|
||||
|
||||
FORCE_INLINE void autotempShutdown() {
|
||||
#if ENABLED(AUTOTEMP)
|
||||
@ -199,4 +303,49 @@ FORCE_INLINE void autotempShutdown() {
|
||||
#endif
|
||||
}
|
||||
|
||||
private:
|
||||
|
||||
void set_current_temp_raw();
|
||||
|
||||
void updateTemperaturesFromRawValues();
|
||||
|
||||
#if ENABLED(HEATER_0_USES_MAX6675)
|
||||
int read_max6675();
|
||||
#endif
|
||||
|
||||
void setExtruderAutoFanState(int pin, bool state);
|
||||
void checkExtruderAutoFans();
|
||||
|
||||
float get_pid_output(int e);
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
float get_pid_output_bed();
|
||||
#endif
|
||||
|
||||
void _temp_error(int e, const char* serial_msg, const char* lcd_msg);
|
||||
void min_temp_error(uint8_t e);
|
||||
void max_temp_error(uint8_t e);
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED
|
||||
|
||||
typedef enum TRState { TRReset, TRInactive, TRFirstHeating, TRStable, TRRunaway } TRstate;
|
||||
|
||||
void thermal_runaway_protection(TRState* state, millis_t* timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc);
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
TRState thermal_runaway_state_machine[EXTRUDERS] = { TRReset };
|
||||
millis_t thermal_runaway_timer[EXTRUDERS] = { 0 };
|
||||
#endif
|
||||
|
||||
#if HAS_THERMALLY_PROTECTED_BED
|
||||
TRState thermal_runaway_bed_state_machine = TRReset;
|
||||
millis_t thermal_runaway_bed_timer;
|
||||
#endif
|
||||
|
||||
#endif // THERMAL_PROTECTION
|
||||
|
||||
};
|
||||
|
||||
extern Temperature thermalManager;
|
||||
|
||||
#endif // TEMPERATURE_H
|
||||
|
||||
@ -479,7 +479,7 @@ inline void line_to_current(AxisEnum axis) {
|
||||
stepper.quick_stop();
|
||||
card.sdprinting = false;
|
||||
card.closefile();
|
||||
autotempShutdown();
|
||||
thermalManager.autotempShutdown();
|
||||
cancel_heatup = true;
|
||||
lcd_setstatus(MSG_PRINT_ABORTED, true);
|
||||
}
|
||||
@ -605,16 +605,16 @@ void lcd_set_home_offsets() {
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0
|
||||
#if TEMP_SENSOR_0 != 0
|
||||
void watch_temp_callback_E0() { start_watching_heater(0); }
|
||||
void watch_temp_callback_E0() { thermalManager.start_watching_heater(0); }
|
||||
#endif
|
||||
#if EXTRUDERS > 1 && TEMP_SENSOR_1 != 0
|
||||
void watch_temp_callback_E1() { start_watching_heater(1); }
|
||||
void watch_temp_callback_E1() { thermalManager.start_watching_heater(1); }
|
||||
#endif // EXTRUDERS > 1
|
||||
#if EXTRUDERS > 2 && TEMP_SENSOR_2 != 0
|
||||
void watch_temp_callback_E2() { start_watching_heater(2); }
|
||||
void watch_temp_callback_E2() { thermalManager.start_watching_heater(2); }
|
||||
#endif // EXTRUDERS > 2
|
||||
#if EXTRUDERS > 3 && TEMP_SENSOR_3 != 0
|
||||
void watch_temp_callback_E3() { start_watching_heater(3); }
|
||||
void watch_temp_callback_E3() { thermalManager.start_watching_heater(3); }
|
||||
#endif // EXTRUDERS > 3
|
||||
#else
|
||||
#if TEMP_SENSOR_0 != 0
|
||||
@ -633,7 +633,7 @@ void lcd_set_home_offsets() {
|
||||
|
||||
#if ENABLED(THERMAL_PROTECTION_BED) && WATCH_BED_TEMP_PERIOD > 0
|
||||
#if TEMP_SENSOR_BED != 0
|
||||
void watch_temp_callback_bed() { start_watching_bed(); }
|
||||
void watch_temp_callback_bed() { thermalManager.start_watching_bed(); }
|
||||
#endif
|
||||
#else
|
||||
#if TEMP_SENSOR_BED != 0
|
||||
@ -670,22 +670,22 @@ static void lcd_tune_menu() {
|
||||
//
|
||||
#if EXTRUDERS == 1
|
||||
#if TEMP_SENSOR_0 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
|
||||
#endif
|
||||
#else //EXTRUDERS > 1
|
||||
#if TEMP_SENSOR_0 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
|
||||
#endif
|
||||
#if TEMP_SENSOR_1 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &thermalManager.target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1);
|
||||
#endif
|
||||
#if EXTRUDERS > 2
|
||||
#if TEMP_SENSOR_2 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &thermalManager.target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2);
|
||||
#endif
|
||||
#if EXTRUDERS > 3
|
||||
#if TEMP_SENSOR_3 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &thermalManager.target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3);
|
||||
#endif
|
||||
#endif // EXTRUDERS > 3
|
||||
#endif // EXTRUDERS > 2
|
||||
@ -695,7 +695,7 @@ static void lcd_tune_menu() {
|
||||
// Bed:
|
||||
//
|
||||
#if TEMP_SENSOR_BED != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &target_temperature_bed, 0, BED_MAXTEMP - 15, watch_temp_callback_bed);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.target_temperature_bed, 0, BED_MAXTEMP - 15, watch_temp_callback_bed);
|
||||
#endif
|
||||
|
||||
//
|
||||
@ -768,9 +768,9 @@ static void lcd_tune_menu() {
|
||||
*
|
||||
*/
|
||||
void _lcd_preheat(int endnum, const float temph, const float tempb, const int fan) {
|
||||
if (temph > 0) setTargetHotend(temph, endnum);
|
||||
if (temph > 0) thermalManager.setTargetHotend(temph, endnum);
|
||||
#if TEMP_SENSOR_BED != 0
|
||||
setTargetBed(tempb);
|
||||
thermalManager.setTargetBed(tempb);
|
||||
#else
|
||||
UNUSED(tempb);
|
||||
#endif
|
||||
@ -805,19 +805,27 @@ void _lcd_preheat(int endnum, const float temph, const float tempb, const int fa
|
||||
|
||||
void lcd_preheat_pla0123() {
|
||||
#if EXTRUDERS > 1
|
||||
setTargetHotend0(plaPreheatHotendTemp);
|
||||
setTargetHotend1(plaPreheatHotendTemp);
|
||||
setTargetHotend2(plaPreheatHotendTemp);
|
||||
thermalManager.setTargetHotend(plaPreheatHotendTemp, 1);
|
||||
#if EXTRUDERS > 2
|
||||
thermalManager.setTargetHotend(plaPreheatHotendTemp, 2);
|
||||
#if EXTRUDERS > 3
|
||||
thermalManager.setTargetHotend(plaPreheatHotendTemp, 3);
|
||||
#endif
|
||||
_lcd_preheat(EXTRUDERS - 1, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed);
|
||||
#endif
|
||||
#endif
|
||||
lcd_preheat_pla0();
|
||||
}
|
||||
void lcd_preheat_abs0123() {
|
||||
#if EXTRUDERS > 1
|
||||
setTargetHotend0(absPreheatHotendTemp);
|
||||
setTargetHotend1(absPreheatHotendTemp);
|
||||
setTargetHotend2(absPreheatHotendTemp);
|
||||
thermalManager.setTargetHotend(absPreheatHotendTemp, 1);
|
||||
#if EXTRUDERS > 2
|
||||
thermalManager.setTargetHotend(absPreheatHotendTemp, 2);
|
||||
#if EXTRUDERS > 3
|
||||
thermalManager.setTargetHotend(absPreheatHotendTemp, 3);
|
||||
#endif
|
||||
_lcd_preheat(EXTRUDERS - 1, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed);
|
||||
#endif
|
||||
#endif
|
||||
lcd_preheat_abs0();
|
||||
}
|
||||
|
||||
#endif // EXTRUDERS > 1
|
||||
@ -879,7 +887,7 @@ void lcd_cooldown() {
|
||||
#if FAN_COUNT > 0
|
||||
for (uint8_t i = 0; i < FAN_COUNT; i++) fanSpeeds[i] = 0;
|
||||
#endif
|
||||
disable_all_heaters();
|
||||
thermalManager.disable_all_heaters();
|
||||
lcd_return_to_status();
|
||||
}
|
||||
|
||||
@ -1414,14 +1422,14 @@ static void lcd_control_menu() {
|
||||
UNUSED(e);
|
||||
#endif
|
||||
PID_PARAM(Ki, e) = scalePID_i(raw_Ki);
|
||||
updatePID();
|
||||
thermalManager.updatePID();
|
||||
}
|
||||
void copy_and_scalePID_d(int e) {
|
||||
#if DISABLED(PID_PARAMS_PER_EXTRUDER)
|
||||
UNUSED(e);
|
||||
#endif
|
||||
PID_PARAM(Kd, e) = scalePID_d(raw_Kd);
|
||||
updatePID();
|
||||
thermalManager.updatePID();
|
||||
}
|
||||
#define _PIDTEMP_BASE_FUNCTIONS(eindex) \
|
||||
void copy_and_scalePID_i_E ## eindex() { copy_and_scalePID_i(eindex); } \
|
||||
@ -1469,22 +1477,22 @@ static void lcd_control_temperature_menu() {
|
||||
//
|
||||
#if EXTRUDERS == 1
|
||||
#if TEMP_SENSOR_0 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
|
||||
#endif
|
||||
#else //EXTRUDERS > 1
|
||||
#if TEMP_SENSOR_0 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0);
|
||||
#endif
|
||||
#if TEMP_SENSOR_1 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &thermalManager.target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1);
|
||||
#endif
|
||||
#if EXTRUDERS > 2
|
||||
#if TEMP_SENSOR_2 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &thermalManager.target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2);
|
||||
#endif
|
||||
#if EXTRUDERS > 3
|
||||
#if TEMP_SENSOR_3 != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3);
|
||||
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &thermalManager.target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3);
|
||||
#endif
|
||||
#endif // EXTRUDERS > 3
|
||||
#endif // EXTRUDERS > 2
|
||||
@ -1494,7 +1502,7 @@ static void lcd_control_temperature_menu() {
|
||||
// Bed:
|
||||
//
|
||||
#if TEMP_SENSOR_BED != 0
|
||||
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_BED, &target_temperature_bed, 0, BED_MAXTEMP - 15);
|
||||
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_BED, &thermalManager.target_temperature_bed, 0, BED_MAXTEMP - 15);
|
||||
#endif
|
||||
|
||||
//
|
||||
|
||||
@ -633,7 +633,7 @@ static void lcd_implementation_status_screen() {
|
||||
//
|
||||
// Hotend 0 Temperature
|
||||
//
|
||||
LCD_TEMP_ONLY(degHotend(0), degTargetHotend(0));
|
||||
LCD_TEMP_ONLY(thermalManager.degHotend(0), thermalManager.degTargetHotend(0));
|
||||
|
||||
//
|
||||
// Hotend 1 or Bed Temperature
|
||||
@ -643,10 +643,10 @@ static void lcd_implementation_status_screen() {
|
||||
lcd.setCursor(8, 0);
|
||||
#if EXTRUDERS > 1
|
||||
lcd.print(LCD_STR_THERMOMETER[0]);
|
||||
LCD_TEMP_ONLY(degHotend(1), degTargetHotend(1));
|
||||
LCD_TEMP_ONLY(thermalManager.degHotend(1), thermalManager.degTargetHotend(1));
|
||||
#else
|
||||
lcd.print(LCD_STR_BEDTEMP[0]);
|
||||
LCD_TEMP_ONLY(degBed(), degTargetBed());
|
||||
LCD_TEMP_ONLY(thermalManager.degBed(), thermalManager.degTargetBed());
|
||||
#endif
|
||||
|
||||
#endif // EXTRUDERS > 1 || TEMP_SENSOR_BED != 0
|
||||
@ -656,7 +656,7 @@ static void lcd_implementation_status_screen() {
|
||||
//
|
||||
// Hotend 0 Temperature
|
||||
//
|
||||
LCD_TEMP(degHotend(0), degTargetHotend(0), LCD_STR_THERMOMETER[0]);
|
||||
LCD_TEMP(thermalManager.degHotend(0), thermalManager.degTargetHotend(0), LCD_STR_THERMOMETER[0]);
|
||||
|
||||
//
|
||||
// Hotend 1 or Bed Temperature
|
||||
@ -664,9 +664,9 @@ static void lcd_implementation_status_screen() {
|
||||
#if EXTRUDERS > 1 || TEMP_SENSOR_BED != 0
|
||||
lcd.setCursor(10, 0);
|
||||
#if EXTRUDERS > 1
|
||||
LCD_TEMP(degHotend(1), degTargetHotend(1), LCD_STR_THERMOMETER[0]);
|
||||
LCD_TEMP(thermalManager.degHotend(1), thermalManager.degTargetHotend(1), LCD_STR_THERMOMETER[0]);
|
||||
#else
|
||||
LCD_TEMP(degBed(), degTargetBed(), LCD_STR_BEDTEMP[0]);
|
||||
LCD_TEMP(thermalManager.degBed(), thermalManager.degTargetBed(), LCD_STR_BEDTEMP[0]);
|
||||
#endif
|
||||
|
||||
#endif // EXTRUDERS > 1 || TEMP_SENSOR_BED != 0
|
||||
@ -702,7 +702,7 @@ static void lcd_implementation_status_screen() {
|
||||
// If we both have a 2nd extruder and a heated bed,
|
||||
// show the heated bed temp on the left,
|
||||
// since the first line is filled with extruder temps
|
||||
LCD_TEMP(degBed(), degTargetBed(), LCD_STR_BEDTEMP[0]);
|
||||
LCD_TEMP(thermalManager.degBed(), thermalManager.degTargetBed(), LCD_STR_BEDTEMP[0]);
|
||||
|
||||
#else
|
||||
// Before homing the axis letters are blinking 'X' <-> '?'.
|
||||
@ -925,9 +925,9 @@ void lcd_implementation_drawedit(const char* pstr, const char* value=NULL) {
|
||||
static uint8_t ledsprev = 0;
|
||||
uint8_t leds = 0;
|
||||
|
||||
if (target_temperature_bed > 0) leds |= LED_A;
|
||||
if (thermalManager.degTargetBed() > 0) leds |= LED_A;
|
||||
|
||||
if (target_temperature[0] > 0) leds |= LED_B;
|
||||
if (thermalManager.degTargetHotend(0) > 0) leds |= LED_B;
|
||||
|
||||
#if FAN_COUNT > 0
|
||||
if (0
|
||||
@ -944,7 +944,7 @@ void lcd_implementation_drawedit(const char* pstr, const char* value=NULL) {
|
||||
#endif // FAN_COUNT > 0
|
||||
|
||||
#if EXTRUDERS > 1
|
||||
if (target_temperature[1] > 0) leds |= LED_C;
|
||||
if (thermalManager.degTargetHotend(1) > 0) leds |= LED_C;
|
||||
#endif
|
||||
|
||||
if (leds != ledsprev) {
|
||||
|
||||
Loading…
Reference in New Issue
Block a user