Modernize configs

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@@ -1106,57 +1106,46 @@
   //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
-  #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
   #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
   #define X_STALLCURRENT  1500 // current in mA where the driver will detect a stall
 
   #define X2_MICROSTEPS     16
-  #define X2_K_VAL          50
   #define X2_OVERCURRENT  2000
   #define X2_STALLCURRENT 1500
 
   #define Y_MICROSTEPS      16
-  #define Y_K_VAL           50
   #define Y_OVERCURRENT   2000
   #define Y_STALLCURRENT  1500
 
   #define Y2_MICROSTEPS     16
-  #define Y2_K_VAL          50
   #define Y2_OVERCURRENT  2000
   #define Y2_STALLCURRENT 1500
 
   #define Z_MICROSTEPS      16
-  #define Z_K_VAL           50
   #define Z_OVERCURRENT   2000
   #define Z_STALLCURRENT  1500
 
   #define Z2_MICROSTEPS     16
-  #define Z2_K_VAL          50
   #define Z2_OVERCURRENT  2000
   #define Z2_STALLCURRENT 1500
 
   #define E0_MICROSTEPS     16
-  #define E0_K_VAL          50
   #define E0_OVERCURRENT  2000
   #define E0_STALLCURRENT 1500
 
   #define E1_MICROSTEPS     16
-  #define E1_K_VAL          50
   #define E1_OVERCURRENT  2000
   #define E1_STALLCURRENT 1500
 
   #define E2_MICROSTEPS     16
-  #define E2_K_VAL          50
   #define E2_OVERCURRENT  2000
   #define E2_STALLCURRENT 1500
 
   #define E3_MICROSTEPS     16
-  #define E3_K_VAL          50
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
   #define E4_MICROSTEPS     16
-  #define E4_K_VAL          50
   #define E4_OVERCURRENT  2000
   #define E4_STALLCURRENT 1500
 
@@ -1298,6 +1287,7 @@
 #if ENABLED(CUSTOM_USER_MENUS)
   #define USER_SCRIPT_DONE "M117 User Script Done"
   #define USER_SCRIPT_AUDIBLE_FEEDBACK
+  //#define USER_SCRIPT_RETURN  // Return to status screen after a script
 
   #define USER_DESC_1 "Home & UBL Info"
   #define USER_GCODE_1 "G28\nG29 W"

Marlin/src/pins/pins_AZTEEG_X3.h

@@ -50,6 +50,9 @@
 //
 // LCD / Controller
 //
+#undef STAT_LED_RED_PIN
+#undef STAT_LED_BLUE_PIN
+
 #if ENABLED(VIKI2) || ENABLED(miniVIKI)
 
   #undef DOGLCD_A0
@@ -59,8 +62,6 @@
   #define DOGLCD_CS         32
   #define BTN_ENC           12
 
-  #undef STAT_LED_RED_PIN
-  #undef STAT_LED_BLUE_PIN
   #define STAT_LED_RED_PIN  64
   #define STAT_LED_BLUE_PIN 63
 

Marlin/src/pins/pins_RAMPS_RE_ARM.h

@@ -248,7 +248,6 @@
   #define DOGLCD_CS           63  // J5-3 & AUX-2
 
   #ifdef ULTIPANEL
-
     #define LCD_PINS_D5       71  // ENET_MDIO
     #define LCD_PINS_D6       73  // ENET_RX_ER
     #define LCD_PINS_D7       75  // ENET_RXD1
@@ -309,12 +308,12 @@
     #define STAT_LED_BLUE_PIN   63  // may change if cable changes
     #define STAT_LED_RED_PIN     6  // may change if cable changes
   #endif
+
   //#define MISO_PIN            50  // system defined J3-10 & AUX-3
   //#define MOSI_PIN            51  // system defined J3-10 & AUX-3
   //#define SCK_PIN             52  // system defined J3-9 & AUX-3
   //#define SS_PIN              53  // system defined J3-5 & AUX-3 - sometimes called SDSS
 
-
   #if ENABLED(MINIPANEL)
     // GLCD features
     //#define LCD_CONTRAST   190