Misc. formatting, serial out

This commit is contained in:
Scott Lahteine 2021-04-13 21:34:21 -05:00
parent 4849d313fd
commit 0e9836649e
7 changed files with 855 additions and 856 deletions

View File

@ -321,7 +321,7 @@ void hook_cpu_exceptions() {
// probably break if the flash happens to be more than 128MB, but in this case, we are not magician, we need help from outside.
unsigned long *vecAddr = (unsigned long*)get_vtor();
SERIAL_ECHO("Vector table addr: ");
SERIAL_ECHOPGM("Vector table addr: ");
SERIAL_PRINTLN(get_vtor(), HEX);
#ifdef VECTOR_TABLE_SIZE
@ -348,7 +348,7 @@ void hook_cpu_exceptions() {
// 128 bytes alignement is required for writing the VTOR register
alignas(128) static unsigned long vectable[VECTOR_TABLE_SENTINEL];
SERIAL_ECHO("Detected vector table size: ");
SERIAL_ECHOPGM("Detected vector table size: ");
SERIAL_PRINTLN(vec_size, HEX);
#endif
@ -372,7 +372,7 @@ void hook_cpu_exceptions() {
HW_REG(0xE000ED08) = (unsigned long)vectable | _BV32(29); // 29th bit is for telling the CPU the table is now in SRAM (should be present already)
SERIAL_ECHOLN("Installed fault handlers");
SERIAL_ECHOLNPGM("Installed fault handlers");
#endif
}

View File

@ -28,11 +28,11 @@
// This is used like SERIAL_ECHOPAIR, that is: a key-value call of the local variables you want
// to dump to the serial port before stopping the CPU.
// \/ Don't replace by SERIAL_ECHOPAIR since ONLY_FILENAME cannot be transformed to a PGM string on Arduino and it breaks building
#define BUG_ON(V...) do { SERIAL_ECHO(ONLY_FILENAME); SERIAL_ECHO(__LINE__); SERIAL_ECHOLN(": "); SERIAL_ECHOLNPAIR(V); SERIAL_FLUSHTX(); *(char*)0 = 42; } while(0)
#define BUG_ON(V...) do { SERIAL_ECHO(ONLY_FILENAME); SERIAL_ECHO(__LINE__); SERIAL_ECHOLNPGM(": "); SERIAL_ECHOLNPAIR(V); SERIAL_FLUSHTX(); *(char*)0 = 42; } while(0)
#elif ENABLED(MARLIN_DEV_MODE)
// Don't stop the CPU here, but at least dump the bug on the serial port
// \/ Don't replace by SERIAL_ECHOPAIR since ONLY_FILENAME cannot be transformed to a PGM string on Arduino and it breaks building
#define BUG_ON(V...) do { SERIAL_ECHO(ONLY_FILENAME); SERIAL_ECHO(__LINE__); SERIAL_ECHOLN(": BUG!"); SERIAL_ECHOLNPAIR(V); SERIAL_FLUSHTX(); } while(0)
#define BUG_ON(V...) do { SERIAL_ECHO(ONLY_FILENAME); SERIAL_ECHO(__LINE__); SERIAL_ECHOLNPGM(": BUG!"); SERIAL_ECHOLNPAIR(V); SERIAL_FLUSHTX(); } while(0)
#else
// Release mode, let's ignore the bug
#define BUG_ON(V...) NOOP

View File

@ -35,22 +35,27 @@
using namespace ExtUI;
namespace Anycubic {
class FileNavigator {
public:
FileNavigator();
void reset();
void getFiles(uint16_t);
void getFiles(uint16_t, panel_type_t, uint8_t filesneeded=4);
void upDIR();
void changeDIR(char *);
void sendFile();
void changeDIR(const char *);
void sendFile(panel_type_t);
void refresh();
char * getCurrentFolderName();
private:
void skiptofileindex(uint16_t);
static FileList filelist;
static char currentfoldername[MAX_PATH_LEN];
static uint16_t lastindex;
static uint8_t folderdepth;
private:
static uint16_t lastpanelindex;
static uint16_t currentindex;
static uint8_t currentfolderdepth;
static uint16_t currentfolderindex[MAX_FOLDER_DEPTH];
static char currentfoldername[MAX_PATH_LEN];
};
extern FileNavigator filenavigator;
}

View File

@ -832,8 +832,8 @@ namespace Anycubic {
setAxisPosition_mm(currZpos+constrain(Zshift,-0.05,0.05),Z);
}
}
} break;
} // end switch
}
}
} break;
case 32: { // A32 clean leveling beep flag
@ -843,7 +843,7 @@ namespace Anycubic {
//TFTSer.println();
} break;
// A33 firmware info request seet PanelInfo()
// A33 firmware info request see PanelInfo()
case 34: { // A34 Adjust single mesh point A34 C/S X1 Y1 V123
if (panel_command[3] == 'C') { // Restore original offsets

View File

@ -109,19 +109,16 @@
#define AC_cmnd_power_loss_recovery PSTR("G28XYR5\nG28Z") // Lift, home X and Y then home Z when in 'safe' position
namespace Anycubic {
enum heater_state_t : uint8_t {
AC_heater_off,
AC_heater_temp_set,
AC_heater_temp_reached
};
enum paused_state_t : uint8_t {
AC_paused_heater_timed_out,
AC_paused_purging_filament,
AC_paused_idle
};
enum printer_state_t : uint8_t {
AC_printer_idle,
AC_printer_probing,
@ -131,13 +128,11 @@ namespace Anycubic {
AC_printer_stopping,
AC_printer_resuming_from_power_outage
};
enum timer_event_t : uint8_t {
AC_timer_started,
AC_timer_paused,
AC_timer_stopped
};
enum media_event_t : uint8_t {
AC_media_inserted,
AC_media_removed,
@ -149,5 +144,4 @@ namespace Anycubic {
AC_menu_change_to_file,
AC_menu_change_to_command
};
} // Anycubic