From 1210b735307b58d524b025df47153c1cf66ec179 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sat, 25 May 2019 16:19:38 -0500 Subject: [PATCH] Geeetech A10M/A20M example updates --- config/examples/Geeetech/A10M/Configuration.h | 33 ++++++++-------- .../Geeetech/A10M/Configuration_adv.h | 14 +++---- config/examples/Geeetech/A20M/Configuration.h | 38 +++++++++---------- .../Geeetech/A20M/Configuration_adv.h | 4 +- 4 files changed, 45 insertions(+), 44 deletions(-) diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index 7369a12eb..ee370d8d9 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -707,9 +707,9 @@ * M204 R Retract Acceleration * M204 T Travel Acceleration */ -#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves -#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts -#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves +#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves // // Use Junction Deviation instead of traditional Jerk Limiting @@ -811,7 +811,8 @@ */ //#define BLTOUCH #if ENABLED(BLTOUCH) - //#define BLTOUCH_DELAY 500 // Minimum Command delay (ms). Enable and increase if needed + #define BLTOUCH_DELAY 200 // Minimum Command delay (ms). Enable and increase if needed + #define BLTOUCH_HS_MODE /** * BLTouch V3.0 and newer smart series @@ -860,7 +861,7 @@ */ #define X_PROBE_OFFSET_FROM_EXTRUDER -37 // X offset: -left +right [of the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.5 // Z offset: -below +above [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.6 // Z offset: -below +above [the nozzle] // Certain types of probes need to stay away from edges #define MIN_PROBE_EDGE 10 @@ -893,16 +894,16 @@ * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. */ -#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow -#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points -#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes -//#define Z_AFTER_PROBING 5 // Z position after probing is done +#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 2 // Z Clearance between multiple probes +#define Z_AFTER_PROBING 3 // Z position after probing is done #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping // For M851 give a range for adjusting the Z probe offset -#define Z_PROBE_OFFSET_RANGE_MIN -20 -#define Z_PROBE_OFFSET_RANGE_MAX 20 +#define Z_PROBE_OFFSET_RANGE_MIN -5 +#define Z_PROBE_OFFSET_RANGE_MAX -0.2 // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -926,7 +927,7 @@ #endif #define PROBING_FANS_OFF // Turn fans off when probing //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing -#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +#define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } @@ -1276,7 +1277,7 @@ #endif // Homing speeds (mm/m) -#define HOMING_FEEDRATE_XY (100*60) +#define HOMING_FEEDRATE_XY (80*60) #define HOMING_FEEDRATE_Z (20*60) // Validate that endstops are triggered on homing moves @@ -1414,7 +1415,7 @@ #if ENABLED(NOZZLE_PARK_FEATURE) // Specify a park position as { X, Y, Z_raise } - #define NOZZLE_PARK_POINT { 3, 3, 10 } + #define NOZZLE_PARK_POINT { 3, (Y_MAX_POS - 3), 10 } #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) #endif @@ -1671,7 +1672,7 @@ // // Note: Usually sold with a white PCB. // -//#define REPRAP_DISCOUNT_SMART_CONTROLLER +#define REPRAP_DISCOUNT_SMART_CONTROLLER // // Original RADDS LCD Display+Encoder+SDCardReader @@ -1687,7 +1688,7 @@ // // ULTIPANEL as seen on Thingiverse. // -#define ULTIPANEL +//#define ULTIPANEL // // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 472747177..1dbfedbbf 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -987,13 +987,13 @@ */ #if HAS_GRAPHICAL_LCD // Show SD percentage next to the progress bar - //#define DOGM_SD_PERCENT + #define DOGM_SD_PERCENT // Enable to save many cycles by drawing a hollow frame on the Info Screen #define XYZ_HOLLOW_FRAME // Enable to save many cycles by drawing a hollow frame on Menu Screens - #define MENU_HOLLOW_FRAME + //#define MENU_HOLLOW_FRAME // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. @@ -1039,11 +1039,11 @@ #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating - //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap - //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap - //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames - //#define STATUS_HEAT_PERCENT // Show heating in a progress bar - //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + #define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + #define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + #define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + #define STATUS_HEAT_PERCENT // Show heating in a progress bar + #define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) // Frivolous Game Options //#define MARLIN_BRICKOUT diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index d455f10d7..1d39509ea 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -707,9 +707,9 @@ * M204 R Retract Acceleration * M204 T Travel Acceleration */ -#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves -#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts -#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves +#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves // // Use Junction Deviation instead of traditional Jerk Limiting @@ -811,7 +811,8 @@ */ //#define BLTOUCH #if ENABLED(BLTOUCH) - //#define BLTOUCH_DELAY 500 // Minimum Command delay (ms). Enable and increase if needed + #define BLTOUCH_DELAY 200 // Minimum Command delay (ms). Enable and increase if needed + #define BLTOUCH_HS_MODE /** * BLTouch V3.0 and newer smart series @@ -860,7 +861,7 @@ */ #define X_PROBE_OFFSET_FROM_EXTRUDER -37 // X offset: -left +right [of the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.5 // Z offset: -below +above [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.6 // Z offset: -below +above [the nozzle] // Certain types of probes need to stay away from edges #define MIN_PROBE_EDGE 10 @@ -893,16 +894,16 @@ * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. */ -#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow -#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points -#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes -//#define Z_AFTER_PROBING 5 // Z position after probing is done +#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 2 // Z Clearance between multiple probes +#define Z_AFTER_PROBING 3 // Z position after probing is done #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping // For M851 give a range for adjusting the Z probe offset -#define Z_PROBE_OFFSET_RANGE_MIN -20 -#define Z_PROBE_OFFSET_RANGE_MAX 20 +#define Z_PROBE_OFFSET_RANGE_MIN -5 +#define Z_PROBE_OFFSET_RANGE_MAX -0.2 // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -926,7 +927,7 @@ #endif #define PROBING_FANS_OFF // Turn fans off when probing //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing -#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +#define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } @@ -1130,7 +1131,7 @@ /** * Enable the G26 Mesh Validation Pattern tool. */ - //#define G26_MESH_VALIDATION + #define G26_MESH_VALIDATION #if ENABLED(G26_MESH_VALIDATION) #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. @@ -1144,7 +1145,7 @@ #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) // Set the number of grid points per dimension. - #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_X 5 #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). @@ -1223,12 +1224,11 @@ * Add a bed leveling sub-menu for ABL or MBL. * Include a guided procedure if manual probing is enabled. */ -//#define LCD_BED_LEVELING - +#define LCD_BED_LEVELING #if ENABLED(LCD_BED_LEVELING) #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment - //#define MESH_EDIT_MENU // Add a menu to edit mesh points + #define MESH_EDIT_MENU // Add a menu to edit mesh points #endif // Add a menu item to move between bed corners for manual bed adjustment @@ -1276,7 +1276,7 @@ #endif // Homing speeds (mm/m) -#define HOMING_FEEDRATE_XY (100*60) +#define HOMING_FEEDRATE_XY (80*60) #define HOMING_FEEDRATE_Z (20*60) // Validate that endstops are triggered on homing moves @@ -1414,7 +1414,7 @@ #if ENABLED(NOZZLE_PARK_FEATURE) // Specify a park position as { X, Y, Z_raise } - #define NOZZLE_PARK_POINT { 3, 3, 10 } + #define NOZZLE_PARK_POINT { 3, (Y_MAX_POS - 3), 10 } #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) #endif diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index d681677b2..3eecc9698 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -791,11 +791,11 @@ //#define LCD_SET_PROGRESS_MANUALLY #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS - //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing #if ENABLED(LCD_PROGRESS_BAR) #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message - #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + #define PROGRESS_MSG_EXPIRE 180000 // (ms) Amount of time to retain the status message (0=forever) //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar #endif