Revert "Coolstep for TMC2130, 2209, 5130, 5160"
Reverting #16790 as not ready for primetime.
This commit is contained in:
Scott Lahteine
parent
28b48fc9bb
commit
18a7276909
@ -2275,166 +2275,6 @@
|
|||||||
#define E6_HYBRID_THRESHOLD 30
|
#define E6_HYBRID_THRESHOLD 30
|
||||||
#define E7_HYBRID_THRESHOLD 30
|
#define E7_HYBRID_THRESHOLD 30
|
||||||
|
|
||||||
/**
|
|
||||||
* CoolStep. Currently supported for TMC2130, TMC2209, TMC5130 and TMC5160 only.
|
|
||||||
* This mode allows for cooler steppers and energy savings.
|
|
||||||
* The driver will switch to coolStep when stepper speed is over COOLSTEP_THRESHOLD mm/s.
|
|
||||||
*
|
|
||||||
* If SG_RESULT goes below COOLSTEP_LOWER_LOAD_THRESHOLD * 32 stepper current will be increased.
|
|
||||||
* Set to 0 to disable CoolStep.
|
|
||||||
*
|
|
||||||
* If SG_RESULT goes above (COOLSTEP_LOWER_LOAD_THRESHOLD + COOLSTEP_UPPER_LOAD_THRESHOLD + 1) * 32
|
|
||||||
* stepper current will be decreased.
|
|
||||||
*
|
|
||||||
* SEUP sets the increase step width. Value range is 0..3 and computed as 2^SEUP.
|
|
||||||
* SEDN sets the decrease delay. Value range is 0..3, 0 being the slowest.
|
|
||||||
* SEIMIN sets the lower current limit. 0: 1/2 of IRUN, 1:1/4 of IRUN
|
|
||||||
*/
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(X)
|
|
||||||
#define X_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define X_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define X_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define X_COOLSTEP_SEUP 2
|
|
||||||
#define X_COOLSTEP_SEDN 0
|
|
||||||
#define X_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(X2)
|
|
||||||
#define X2_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define X2_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define X2_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define X2_COOLSTEP_SEUP 2
|
|
||||||
#define X2_COOLSTEP_SEDN 0
|
|
||||||
#define X2_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(Y)
|
|
||||||
#define Y_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define Y_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define Y_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define Y_COOLSTEP_SEUP 2
|
|
||||||
#define Y_COOLSTEP_SEDN 0
|
|
||||||
#define Y_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(Y2)
|
|
||||||
#define Y2_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define Y2_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define Y2_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define Y2_COOLSTEP_SEUP 2
|
|
||||||
#define Y2_COOLSTEP_SEDN 0
|
|
||||||
#define Y2_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(Z)
|
|
||||||
#define Z_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define Z_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define Z_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define Z_COOLSTEP_SEUP 2
|
|
||||||
#define Z_COOLSTEP_SEDN 0
|
|
||||||
#define Z_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(Z2)
|
|
||||||
#define Z2_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define Z2_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define Z2_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define Z2_COOLSTEP_SEUP 2
|
|
||||||
#define Z2_COOLSTEP_SEDN 0
|
|
||||||
#define Z2_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(Z3)
|
|
||||||
#define Z3_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define Z3_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define Z3_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define Z3_COOLSTEP_SEUP 2
|
|
||||||
#define Z3_COOLSTEP_SEDN 0
|
|
||||||
#define Z3_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(Z4)
|
|
||||||
#define Z4_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define Z4_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define Z4_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define Z4_COOLSTEP_SEUP 2
|
|
||||||
#define Z4_COOLSTEP_SEDN 0
|
|
||||||
#define Z4_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(E0)
|
|
||||||
#define E0_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define E0_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define E0_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define E0_COOLSTEP_SEUP 2
|
|
||||||
#define E0_COOLSTEP_SEDN 0
|
|
||||||
#define E0_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(E1)
|
|
||||||
#define E1_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define E1_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define E1_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define E1_COOLSTEP_SEUP 2
|
|
||||||
#define E1_COOLSTEP_SEDN 0
|
|
||||||
#define E1_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(E2)
|
|
||||||
#define E2_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define E2_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define E2_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define E2_COOLSTEP_SEUP 2
|
|
||||||
#define E2_COOLSTEP_SEDN 0
|
|
||||||
#define E2_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(E3)
|
|
||||||
#define E3_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define E3_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define E3_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define E3_COOLSTEP_SEUP 2
|
|
||||||
#define E3_COOLSTEP_SEDN 0
|
|
||||||
#define E3_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(E4)
|
|
||||||
#define E4_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define E4_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define E4_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define E4_COOLSTEP_SEUP 2
|
|
||||||
#define E4_COOLSTEP_SEDN 0
|
|
||||||
#define E4_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(E5)
|
|
||||||
#define E5_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define E5_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define E5_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define E5_COOLSTEP_SEUP 2
|
|
||||||
#define E5_COOLSTEP_SEDN 0
|
|
||||||
#define E5_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(E6)
|
|
||||||
#define E6_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define E6_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define E6_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define E6_COOLSTEP_SEUP 2
|
|
||||||
#define E6_COOLSTEP_SEDN 0
|
|
||||||
#define E6_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if AXIS_HAS_COOLSTEP(E7)
|
|
||||||
#define E7_COOLSTEP_SPEED_THRESHOLD 5
|
|
||||||
#define E7_COOLSTEP_LOWER_LOAD_THRESHOLD 7
|
|
||||||
#define E7_COOLSTEP_UPPER_LOAD_THRESHOLD 0
|
|
||||||
#define E7_COOLSTEP_SEUP 2
|
|
||||||
#define E7_COOLSTEP_SEDN 0
|
|
||||||
#define E7_COOLSTEP_SEIMIN 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Use StallGuard2 to home / probe X, Y, Z.
|
* Use StallGuard2 to home / probe X, Y, Z.
|
||||||
*
|
*
|
||||||
|
|||||||
@ -137,13 +137,6 @@ class TMCMarlin : public TMC, public TMCStorage<AXIS_LETTER, DRIVER_ID> {
|
|||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
uint32_t get_cool_thrs() {
|
|
||||||
return _tmc_thrs(this->microsteps(), this->TCOOLTHRS(), planner.settings.axis_steps_per_mm[AXIS_ID]);
|
|
||||||
}
|
|
||||||
void set_cool_thrs(const uint32_t thrs) {
|
|
||||||
TMC::TCOOLTHRS(_tmc_thrs(this->microsteps(), thrs, planner.settings.axis_steps_per_mm[AXIS_ID]));
|
|
||||||
}
|
|
||||||
|
|
||||||
#if HAS_LCD_MENU
|
#if HAS_LCD_MENU
|
||||||
inline void refresh_stepper_current() { rms_current(this->val_mA); }
|
inline void refresh_stepper_current() { rms_current(this->val_mA); }
|
||||||
|
|
||||||
@ -240,14 +233,6 @@ class TMCMarlin<TMC2209Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> : public TMC220
|
|||||||
#endif
|
#endif
|
||||||
}
|
}
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
uint32_t get_cool_thrs() {
|
|
||||||
return _tmc_thrs(this->microsteps(), this->TCOOLTHRS(), planner.settings.axis_steps_per_mm[AXIS_ID]);
|
|
||||||
}
|
|
||||||
void set_cool_thrs(const uint32_t thrs) {
|
|
||||||
TMC2209Stepper::TCOOLTHRS(_tmc_thrs(this->microsteps(), thrs, planner.settings.axis_steps_per_mm[AXIS_ID]));
|
|
||||||
}
|
|
||||||
|
|
||||||
#if USE_SENSORLESS
|
#if USE_SENSORLESS
|
||||||
inline int16_t homing_threshold() { return TMC2209Stepper::SGTHRS(); }
|
inline int16_t homing_threshold() { return TMC2209Stepper::SGTHRS(); }
|
||||||
void homing_threshold(int16_t sgt_val) {
|
void homing_threshold(int16_t sgt_val) {
|
||||||
@ -261,6 +246,7 @@ class TMCMarlin<TMC2209Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> : public TMC220
|
|||||||
|
|
||||||
#if HAS_LCD_MENU
|
#if HAS_LCD_MENU
|
||||||
inline void refresh_stepper_current() { rms_current(this->val_mA); }
|
inline void refresh_stepper_current() { rms_current(this->val_mA); }
|
||||||
|
|
||||||
#if ENABLED(HYBRID_THRESHOLD)
|
#if ENABLED(HYBRID_THRESHOLD)
|
||||||
inline void refresh_hybrid_thrs() { set_pwm_thrs(this->stored.hybrid_thrs); }
|
inline void refresh_hybrid_thrs() { set_pwm_thrs(this->stored.hybrid_thrs); }
|
||||||
#endif
|
#endif
|
||||||
|
|||||||
@ -2040,62 +2040,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
|||||||
#error "LED_USER_PRESET_STARTUP is required for FYSETC_MINI_12864 2.x displays."
|
#error "LED_USER_PRESET_STARTUP is required for FYSETC_MINI_12864 2.x displays."
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
|
||||||
* Make sure CoolStep settings exist
|
|
||||||
*/
|
|
||||||
#if HAS_COOLSTEP
|
|
||||||
#define NEEDS_COOLSTEP(A) AXIS_HAS_COOLSTEP(A) && !(defined(A##_COOLSTEP_SPEED_THRESHOLD) && defined(A##_COOLSTEP_LOWER_LOAD_THRESHOLD) && defined(A##_COOLSTEP_UPPER_LOAD_THRESHOLD) && defined(A##_COOLSTEP_SEUP) && defined(A##_COOLSTEP_SEDN) && defined(A##_COOLSTEP_SEIMIN))
|
|
||||||
#if NEEDS_COOLSTEP(X)
|
|
||||||
#error "X COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(X2)
|
|
||||||
#error "X2 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(Y)
|
|
||||||
#error "Y COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(Y2)
|
|
||||||
#error "Y2 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(Z)
|
|
||||||
#error "Z COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(Z2)
|
|
||||||
#error "Z2 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(Z3)
|
|
||||||
#error "Z3 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(Z4)
|
|
||||||
#error "Z4 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(E0)
|
|
||||||
#error "E0 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(E1)
|
|
||||||
#error "E1 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(E2)
|
|
||||||
#error "E2 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(E3)
|
|
||||||
#error "E3 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(E4)
|
|
||||||
#error "E4 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(E5)
|
|
||||||
#error "E5 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(E6)
|
|
||||||
#error "E6 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#if NEEDS_COOLSTEP(E7)
|
|
||||||
#error "E7 COOLSTEP settings must be defined in Configuration_adv.h."
|
|
||||||
#endif
|
|
||||||
#undef NEEDS_COOLSTEP
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Check existing CS pins against enabled TMC SPI drivers.
|
* Check existing CS pins against enabled TMC SPI drivers.
|
||||||
*/
|
*/
|
||||||
|
|||||||
@ -36,19 +36,7 @@
|
|||||||
#include <SPI.h>
|
#include <SPI.h>
|
||||||
|
|
||||||
enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
||||||
#define _TMC_INIT_1(ST, STEALTH_INDEX) tmc_init(stepper##ST, ST##_CURRENT, ST##_MICROSTEPS)
|
#define TMC_INIT(ST, STEALTH_INDEX) tmc_init(stepper##ST, ST##_CURRENT, ST##_MICROSTEPS, ST##_HYBRID_THRESHOLD, stealthchop_by_axis[STEALTH_INDEX])
|
||||||
#define _TMC_INIT_2(ST, STEALTH_INDEX) tmc_init(stepper##ST, ST##_CURRENT, ST##_MICROSTEPS, stealthchop_by_axis[STEALTH_INDEX], ST##_HYBRID_THRESHOLD)
|
|
||||||
#define _TMC_INIT_3(ST, STEALTH_INDEX) tmc_init(stepper##ST, ST##_CURRENT, ST##_MICROSTEPS, stealthchop_by_axis[STEALTH_INDEX], ST##_HYBRID_THRESHOLD, ST##_COOLSTEP_SPEED_THRESHOLD, ST##_COOLSTEP_LOWER_LOAD_THRESHOLD, ST##_COOLSTEP_UPPER_LOAD_THRESHOLD, ST##_COOLSTEP_SEUP, ST##_COOLSTEP_SEDN, ST##_COOLSTEP_SEIMIN)
|
|
||||||
#define _TMC_INIT_TMC2660(ST, STEALTH_INDEX) _TMC_INIT_1(ST, STEALTH_INDEX)
|
|
||||||
#define _TMC_INIT_TMC2160(ST, STEALTH_INDEX) _TMC_INIT_2(ST, STEALTH_INDEX)
|
|
||||||
#define _TMC_INIT_TMC2208(ST, STEALTH_INDEX) _TMC_INIT_2(ST, STEALTH_INDEX)
|
|
||||||
#define _TMC_INIT_TMC5130(ST, STEALTH_INDEX) _TMC_INIT_3(ST, STEALTH_INDEX)
|
|
||||||
#define _TMC_INIT_TMC5160(ST, STEALTH_INDEX) _TMC_INIT_3(ST, STEALTH_INDEX)
|
|
||||||
#define _TMC_INIT_TMC2130(ST, STEALTH_INDEX) _TMC_INIT_3(ST, STEALTH_INDEX)
|
|
||||||
#define _TMC_INIT_TMC2209(ST, STEALTH_INDEX) _TMC_INIT_3(ST, STEALTH_INDEX)
|
|
||||||
#define __TMC_INIT(DRV, ST, STEALTH_INDEX) _TMC_INIT_##DRV(ST, STEALTH_INDEX)
|
|
||||||
#define _TMC_INIT(DRV, ST, STEALTH_INDEX) __TMC_INIT(DRV, ST, STEALTH_INDEX)
|
|
||||||
#define TMC_INIT(ST, STEALTH_INDEX) _TMC_INIT(ST##_DRIVER_TYPE, ST, STEALTH_INDEX)
|
|
||||||
|
|
||||||
// IC = TMC model number
|
// IC = TMC model number
|
||||||
// ST = Stepper object letter
|
// ST = Stepper object letter
|
||||||
@ -134,19 +122,7 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
|
|
||||||
#if HAS_DRIVER(TMC2130)
|
#if HAS_DRIVER(TMC2130)
|
||||||
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
||||||
void tmc_init(
|
void tmc_init(TMCMarlin<TMC2130Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st, const uint16_t mA, const uint16_t microsteps, const uint32_t hyb_thrs, const bool stealth) {
|
||||||
TMCMarlin<TMC2130Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st,
|
|
||||||
const uint16_t mA,
|
|
||||||
const uint16_t microsteps,
|
|
||||||
const bool stealth,
|
|
||||||
const uint32_t hyb_thrs,
|
|
||||||
const uint32_t cool_thrs,
|
|
||||||
const uint8_t cool_semin,
|
|
||||||
const uint8_t cool_semax,
|
|
||||||
const uint8_t cool_seup,
|
|
||||||
const uint8_t cool_sedn,
|
|
||||||
const bool cool_seimin
|
|
||||||
) {
|
|
||||||
st.begin();
|
st.begin();
|
||||||
|
|
||||||
CHOPCONF_t chopconf{0};
|
CHOPCONF_t chopconf{0};
|
||||||
@ -181,28 +157,13 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
UNUSED(hyb_thrs);
|
UNUSED(hyb_thrs);
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
st.set_cool_thrs(cool_thrs); // (mm/s)
|
|
||||||
COOLCONF_t coolconf{0};
|
|
||||||
coolconf.semin = cool_semin;
|
|
||||||
coolconf.semax = cool_semax;
|
|
||||||
coolconf.seup = cool_seup;
|
|
||||||
coolconf.sedn = cool_sedn;
|
|
||||||
coolconf.seimin = cool_seimin;
|
|
||||||
st.COOLCONF(coolconf.sr);
|
|
||||||
|
|
||||||
st.GSTAT(); // Clear GSTAT
|
st.GSTAT(); // Clear GSTAT
|
||||||
}
|
}
|
||||||
#endif // TMC2130
|
#endif // TMC2130
|
||||||
|
|
||||||
#if HAS_DRIVER(TMC2160)
|
#if HAS_DRIVER(TMC2160)
|
||||||
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
||||||
void tmc_init(
|
void tmc_init(TMCMarlin<TMC2160Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st, const uint16_t mA, const uint16_t microsteps, const uint32_t hyb_thrs, const bool stealth) {
|
||||||
TMCMarlin<TMC2160Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st,
|
|
||||||
const uint16_t mA,
|
|
||||||
const uint16_t microsteps,
|
|
||||||
const bool stealth,
|
|
||||||
const uint32_t hyb_thrs
|
|
||||||
) {
|
|
||||||
st.begin();
|
st.begin();
|
||||||
|
|
||||||
CHOPCONF_t chopconf{0};
|
CHOPCONF_t chopconf{0};
|
||||||
@ -479,13 +440,7 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
|
|
||||||
#if HAS_DRIVER(TMC2208)
|
#if HAS_DRIVER(TMC2208)
|
||||||
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
||||||
void tmc_init(
|
void tmc_init(TMCMarlin<TMC2208Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st, const uint16_t mA, const uint16_t microsteps, const uint32_t hyb_thrs, const bool stealth) {
|
||||||
TMCMarlin<TMC2208Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st,
|
|
||||||
const uint16_t mA,
|
|
||||||
const uint16_t microsteps,
|
|
||||||
const bool stealth,
|
|
||||||
const uint32_t hyb_thrs
|
|
||||||
) {
|
|
||||||
TMC2208_n::GCONF_t gconf{0};
|
TMC2208_n::GCONF_t gconf{0};
|
||||||
gconf.pdn_disable = true; // Use UART
|
gconf.pdn_disable = true; // Use UART
|
||||||
gconf.mstep_reg_select = true; // Select microsteps with UART
|
gconf.mstep_reg_select = true; // Select microsteps with UART
|
||||||
@ -533,19 +488,7 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
|
|
||||||
#if HAS_DRIVER(TMC2209)
|
#if HAS_DRIVER(TMC2209)
|
||||||
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
||||||
void tmc_init(
|
void tmc_init(TMCMarlin<TMC2209Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st, const uint16_t mA, const uint16_t microsteps, const uint32_t hyb_thrs, const bool stealth) {
|
||||||
TMCMarlin<TMC2209Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st,
|
|
||||||
const uint16_t mA,
|
|
||||||
const uint16_t microsteps,
|
|
||||||
const bool stealth,
|
|
||||||
const uint32_t hyb_thrs,
|
|
||||||
const uint32_t cool_thrs,
|
|
||||||
const uint8_t cool_semin,
|
|
||||||
const uint8_t cool_semax,
|
|
||||||
const uint8_t cool_seup,
|
|
||||||
const uint8_t cool_sedn,
|
|
||||||
const bool cool_seimin
|
|
||||||
) {
|
|
||||||
TMC2208_n::GCONF_t gconf{0};
|
TMC2208_n::GCONF_t gconf{0};
|
||||||
gconf.pdn_disable = true; // Use UART
|
gconf.pdn_disable = true; // Use UART
|
||||||
gconf.mstep_reg_select = true; // Select microsteps with UART
|
gconf.mstep_reg_select = true; // Select microsteps with UART
|
||||||
@ -586,15 +529,6 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
UNUSED(hyb_thrs);
|
UNUSED(hyb_thrs);
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
st.set_cool_thrs(cool_thrs); // (mm/s)
|
|
||||||
COOLCONF_t coolconf{0};
|
|
||||||
coolconf.semin = cool_semin;
|
|
||||||
coolconf.semax = cool_semax;
|
|
||||||
coolconf.seup = cool_seup;
|
|
||||||
coolconf.sedn = cool_sedn;
|
|
||||||
coolconf.seimin = cool_seimin;
|
|
||||||
st.COOLCONF(coolconf.sr);
|
|
||||||
|
|
||||||
st.GSTAT(0b111); // Clear
|
st.GSTAT(0b111); // Clear
|
||||||
delay(200);
|
delay(200);
|
||||||
}
|
}
|
||||||
@ -602,11 +536,7 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
|
|
||||||
#if HAS_DRIVER(TMC2660)
|
#if HAS_DRIVER(TMC2660)
|
||||||
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
||||||
void tmc_init(
|
void tmc_init(TMCMarlin<TMC2660Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st, const uint16_t mA, const uint16_t microsteps, const uint32_t, const bool) {
|
||||||
TMCMarlin<TMC2660Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st,
|
|
||||||
const uint16_t mA,
|
|
||||||
const uint16_t microsteps
|
|
||||||
) {
|
|
||||||
st.begin();
|
st.begin();
|
||||||
|
|
||||||
TMC2660_n::CHOPCONF_t chopconf{0};
|
TMC2660_n::CHOPCONF_t chopconf{0};
|
||||||
@ -633,19 +563,7 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
|
|
||||||
#if HAS_DRIVER(TMC5130)
|
#if HAS_DRIVER(TMC5130)
|
||||||
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
||||||
void tmc_init(
|
void tmc_init(TMCMarlin<TMC5130Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st, const uint16_t mA, const uint16_t microsteps, const uint32_t hyb_thrs, const bool stealth) {
|
||||||
TMCMarlin<TMC5130Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st,
|
|
||||||
const uint16_t mA,
|
|
||||||
const uint16_t microsteps,
|
|
||||||
const bool stealth,
|
|
||||||
const uint32_t hyb_thrs,
|
|
||||||
const uint32_t cool_thrs,
|
|
||||||
const uint8_t cool_semin,
|
|
||||||
const uint8_t cool_semax,
|
|
||||||
const uint8_t cool_seup,
|
|
||||||
const uint8_t cool_sedn,
|
|
||||||
const bool cool_seimin
|
|
||||||
) {
|
|
||||||
st.begin();
|
st.begin();
|
||||||
|
|
||||||
CHOPCONF_t chopconf{0};
|
CHOPCONF_t chopconf{0};
|
||||||
@ -680,34 +598,13 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
UNUSED(hyb_thrs);
|
UNUSED(hyb_thrs);
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
st.set_cool_thrs(cool_thrs); // (mm/s)
|
|
||||||
COOLCONF_t coolconf{0};
|
|
||||||
coolconf.semin = cool_semin;
|
|
||||||
coolconf.semax = cool_semax;
|
|
||||||
coolconf.seup = cool_seup;
|
|
||||||
coolconf.sedn = cool_sedn;
|
|
||||||
coolconf.seimin = cool_seimin;
|
|
||||||
st.COOLCONF(coolconf.sr);
|
|
||||||
|
|
||||||
st.GSTAT(); // Clear GSTAT
|
st.GSTAT(); // Clear GSTAT
|
||||||
}
|
}
|
||||||
#endif // TMC5130
|
#endif // TMC5130
|
||||||
|
|
||||||
#if HAS_DRIVER(TMC5160)
|
#if HAS_DRIVER(TMC5160)
|
||||||
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
template<char AXIS_LETTER, char DRIVER_ID, AxisEnum AXIS_ID>
|
||||||
void tmc_init(
|
void tmc_init(TMCMarlin<TMC5160Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st, const uint16_t mA, const uint16_t microsteps, const uint32_t hyb_thrs, const bool stealth) {
|
||||||
TMCMarlin<TMC5160Stepper, AXIS_LETTER, DRIVER_ID, AXIS_ID> &st,
|
|
||||||
const uint16_t mA,
|
|
||||||
const uint16_t microsteps,
|
|
||||||
const bool stealth,
|
|
||||||
const uint32_t hyb_thrs,
|
|
||||||
const uint32_t cool_thrs,
|
|
||||||
const uint8_t cool_semin,
|
|
||||||
const uint8_t cool_semax,
|
|
||||||
const uint8_t cool_seup,
|
|
||||||
const uint8_t cool_sedn,
|
|
||||||
const bool cool_seimin
|
|
||||||
) {
|
|
||||||
st.begin();
|
st.begin();
|
||||||
|
|
||||||
CHOPCONF_t chopconf{0};
|
CHOPCONF_t chopconf{0};
|
||||||
@ -744,16 +641,6 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
|
|||||||
#else
|
#else
|
||||||
UNUSED(hyb_thrs);
|
UNUSED(hyb_thrs);
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
st.set_cool_thrs(cool_thrs); // (mm/s)
|
|
||||||
COOLCONF_t coolconf{0};
|
|
||||||
coolconf.semin = cool_semin;
|
|
||||||
coolconf.semax = cool_semax;
|
|
||||||
coolconf.seup = cool_seup;
|
|
||||||
coolconf.sedn = cool_sedn;
|
|
||||||
coolconf.seimin = cool_seimin;
|
|
||||||
st.COOLCONF(coolconf.sr);
|
|
||||||
|
|
||||||
st.GSTAT(); // Clear GSTAT
|
st.GSTAT(); // Clear GSTAT
|
||||||
}
|
}
|
||||||
#endif // TMC5160
|
#endif // TMC5160
|
||||||
|
|||||||
Loading…
Reference in New Issue
Block a user