Misc. formatting, serial out

Marlin/src/HAL/shared/cpu_exception/exception_arm.cpp

@@ -321,7 +321,7 @@ void hook_cpu_exceptions() {
     // probably break if the flash happens to be more than 128MB, but in this case, we are not magician, we need help from outside.
 
     unsigned long *vecAddr = (unsigned long*)get_vtor();
-    SERIAL_ECHO("Vector table addr: ");
+    SERIAL_ECHOPGM("Vector table addr: ");
     SERIAL_PRINTLN(get_vtor(), HEX);
 
     #ifdef VECTOR_TABLE_SIZE
@@ -348,7 +348,7 @@ void hook_cpu_exceptions() {
       // 128 bytes alignement is required for writing the VTOR register
       alignas(128) static unsigned long vectable[VECTOR_TABLE_SENTINEL];
 
-      SERIAL_ECHO("Detected vector table size: ");
+      SERIAL_ECHOPGM("Detected vector table size: ");
       SERIAL_PRINTLN(vec_size, HEX);
     #endif
 
@@ -372,7 +372,7 @@ void hook_cpu_exceptions() {
 
     HW_REG(0xE000ED08) = (unsigned long)vectable | _BV32(29); // 29th bit is for telling the CPU the table is now in SRAM (should be present already)
 
-    SERIAL_ECHOLN("Installed fault handlers");
+    SERIAL_ECHOLNPGM("Installed fault handlers");
   #endif
 }
 

Marlin/src/core/bug_on.h

@@ -28,11 +28,11 @@
   // This is used like SERIAL_ECHOPAIR, that is: a key-value call of the local variables you want
   // to dump to the serial port before stopping the CPU.
                           // \/ Don't replace by SERIAL_ECHOPAIR since ONLY_FILENAME cannot be transformed to a PGM string on Arduino and it breaks building
-  #define BUG_ON(V...) do { SERIAL_ECHO(ONLY_FILENAME); SERIAL_ECHO(__LINE__); SERIAL_ECHOLN(": "); SERIAL_ECHOLNPAIR(V); SERIAL_FLUSHTX(); *(char*)0 = 42; } while(0)
+  #define BUG_ON(V...) do { SERIAL_ECHO(ONLY_FILENAME); SERIAL_ECHO(__LINE__); SERIAL_ECHOLNPGM(": "); SERIAL_ECHOLNPAIR(V); SERIAL_FLUSHTX(); *(char*)0 = 42; } while(0)
 #elif ENABLED(MARLIN_DEV_MODE)
   // Don't stop the CPU here, but at least dump the bug on the serial port
                           // \/ Don't replace by SERIAL_ECHOPAIR since ONLY_FILENAME cannot be transformed to a PGM string on Arduino and it breaks building
-  #define BUG_ON(V...) do { SERIAL_ECHO(ONLY_FILENAME); SERIAL_ECHO(__LINE__); SERIAL_ECHOLN(": BUG!"); SERIAL_ECHOLNPAIR(V); SERIAL_FLUSHTX(); } while(0)
+  #define BUG_ON(V...) do { SERIAL_ECHO(ONLY_FILENAME); SERIAL_ECHO(__LINE__); SERIAL_ECHOLNPGM(": BUG!"); SERIAL_ECHOLNPAIR(V); SERIAL_FLUSHTX(); } while(0)
 #else
   // Release mode, let's ignore the bug
   #define BUG_ON(V...) NOOP

Marlin/src/lcd/extui/lib/anycubic_chiron/FileNavigator.h

@@ -35,22 +35,27 @@
 using namespace ExtUI;
 
 namespace Anycubic {
+
 class FileNavigator {
   public:
     FileNavigator();
     void reset();
-      void   getFiles(uint16_t);
+    void getFiles(uint16_t, panel_type_t, uint8_t filesneeded=4);
     void upDIR();
-      void   changeDIR(char *);
-      void   sendFile();
+    void changeDIR(const char *);
+    void sendFile(panel_type_t);
     void refresh();
-      char * getCurrentFolderName();
-    private:
+    void skiptofileindex(uint16_t);
+
     static FileList filelist;
-      static char      currentfoldername[MAX_PATH_LEN];
-      static uint16_t  lastindex;
-      static uint8_t   folderdepth;
+  private:
+    static uint16_t lastpanelindex;
     static uint16_t currentindex;
+    static uint8_t  currentfolderdepth;
+    static uint16_t currentfolderindex[MAX_FOLDER_DEPTH];
+    static char     currentfoldername[MAX_PATH_LEN];
 };
+
 extern FileNavigator filenavigator;
+
 }

Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp

@@ -832,8 +832,8 @@ namespace Anycubic {
               setAxisPosition_mm(currZpos+constrain(Zshift,-0.05,0.05),Z);
             }
           }
-          } break;
-        } // end switch
+        }
+      }
     } break;
 
     case 32: { // A32 clean leveling beep flag
@@ -843,7 +843,7 @@ namespace Anycubic {
       //TFTSer.println();
     } break;
 
-      // A33 firmware info request seet PanelInfo()
+    // A33 firmware info request see PanelInfo()
 
     case 34: {  // A34 Adjust single mesh point A34 C/S X1 Y1 V123
       if (panel_command[3] == 'C') { // Restore original offsets

Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft_defs.h

@@ -109,19 +109,16 @@
 #define AC_cmnd_power_loss_recovery    PSTR("G28XYR5\nG28Z")           // Lift, home X and Y then home Z when in 'safe' position
 
 namespace Anycubic {
-
   enum heater_state_t : uint8_t {
     AC_heater_off,
     AC_heater_temp_set,
     AC_heater_temp_reached
   };
-
   enum paused_state_t : uint8_t {
     AC_paused_heater_timed_out,
     AC_paused_purging_filament,
     AC_paused_idle
   };
-
   enum printer_state_t : uint8_t {
     AC_printer_idle,
     AC_printer_probing,
@@ -131,13 +128,11 @@ namespace Anycubic {
     AC_printer_stopping,
     AC_printer_resuming_from_power_outage
   };
-
   enum timer_event_t : uint8_t {
     AC_timer_started,
     AC_timer_paused,
     AC_timer_stopped
   };
-
   enum media_event_t : uint8_t {
     AC_media_inserted,
     AC_media_removed,
@@ -149,5 +144,4 @@ namespace Anycubic {
     AC_menu_change_to_file,
     AC_menu_change_to_command
   };
-
 } // Anycubic