Fysetc rename Part 2

Marlin/Makefile

@@ -237,7 +237,7 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1134)
 else ifeq ($(HARDWARE_MOTHERBOARD),1135)
 # Dagoma F5
 else ifeq ($(HARDWARE_MOTHERBOARD),1136)
-# Fysetc F6
+# FYSETC F6
 else ifeq ($(HARDWARE_MOTHERBOARD),1137)
 # Duplicator i3 Plus
 else ifeq ($(HARDWARE_MOTHERBOARD),1138)

Marlin/src/core/boards.h

@@ -88,7 +88,7 @@
 #define BOARD_RAMPS_ENDER_4           1134  // Creality: Ender-4, CR-8
 #define BOARD_RAMPS_CREALITY          1135  // Creality: CR10S, CR20, CR-X
 #define BOARD_RAMPS_DAGOMA            1136  // Dagoma F5
-#define BOARD_FYSETC_F6_13            1137  // Fysetc F6
+#define BOARD_FYSETC_F6_13            1137  // FYSETC F6
 #define BOARD_DUPLICATOR_I3_PLUS      1138  // Wanhao Duplicator i3 Plus
 #define BOARD_VORON                   1139  // VORON Design
 #define BOARD_TRONXY_V3_1_0           1140  // Tronxy TRONXY-V3-1.0

Marlin/src/inc/SanityCheck.h

@@ -1561,7 +1561,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
  * LED Backlight Timeout
  */
 #if defined(LED_BACKLIGHT_TIMEOUT) && !(EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1) && HAS_POWER_SWITCH)
-  #error "LED_BACKLIGHT_TIMEOUT requires a Fysetc Mini Panel and a Power Switch."
+  #error "LED_BACKLIGHT_TIMEOUT requires a FYSETC Mini Panel and a Power Switch."
 #endif
 
 /**

Marlin/src/pins/lpc1768/pins_MKS_SBASE.h

@@ -231,33 +231,33 @@
 
   #if ENABLED(FYSETC_MINI_12864)
     /**
-     * The Fysetc display can NOT use the SCK and MOSI pins on EXP2, so a
+     * The FYSETC display can NOT use the SCK and MOSI pins on EXP2, so a
      * special cable is needed to go between EXP2 on the FYSETC and the
      * controller board's EXP2 and J8. It also means that a software SPI
      * is needed to drive those pins.
      *
-     * The Fysetc requires mode 3 SPI interface.
+     * The FYSETC requires mode 3 SPI interface.
      *
      * Pins 6, 7 & 8 on EXP2 are no connects. That means a second special
      * cable will be needed if the RGB LEDs are to be active.
      */
-    #define DOGLCD_CS      LCD_PINS_ENABLE // EXP1.3  (LCD_EN on Fysetc schematic)
+    #define DOGLCD_CS      LCD_PINS_ENABLE // EXP1.3  (LCD_EN on FYSETC schematic)
-    #define DOGLCD_A0      LCD_PINS_RS     // EXP1.4  (LCD_A0 on Fysetc schematic)
+    #define DOGLCD_A0      LCD_PINS_RS     // EXP1.4  (LCD_A0 on FYSETC schematic)
-    #define DOGLCD_SCK     P2_11           // J8-5  (SCK on Fysetc schematic)
+    #define DOGLCD_SCK     P2_11           // J8-5  (SCK on FYSETC schematic)
-    #define DOGLCD_MOSI    P4_28           // J8-6  (MOSI on Fysetc schematic)
+    #define DOGLCD_MOSI    P4_28           // J8-6  (MOSI on FYSETC schematic)
 
     //#define FORCE_SOFT_SPI    // Use this if default of hardware SPI causes display problems
                                 //   results in LCD soft SPI mode 3, SD soft SPI mode 0
 
     #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
       #ifndef RGB_LED_R_PIN
-        #define RGB_LED_R_PIN P2_12        // J8-4  (LCD_D6 on Fysetc schematic)
+        #define RGB_LED_R_PIN P2_12        // J8-4  (LCD_D6 on FYSETC schematic)
       #endif
       #ifndef RGB_LED_G_PIN
-        #define RGB_LED_G_PIN P1_23        // J8-3  (LCD_D5 on Fysetc schematic)
+        #define RGB_LED_G_PIN P1_23        // J8-3  (LCD_D5 on FYSETC schematic)
       #endif
       #ifndef RGB_LED_B_PIN
-        #define RGB_LED_B_PIN P1_22        // J8-2  (LCD_D7 on Fysetc schematic)
+        #define RGB_LED_B_PIN P1_22        // J8-2  (LCD_D7 on FYSETC schematic)
       #endif
     #elif ENABLED(FYSETC_MINI_12864_2_1)
       #define NEOPIXEL_PIN P2_12

Marlin/src/pins/ramps/pins_FYSETC_F6_13.h

@@ -22,7 +22,7 @@
 #pragma once
 
 //
-// Fysetc F6 pin assignments
+// FYSETC F6 pin assignments
 //
 
 #ifndef __AVR_ATmega2560__