parent
2b628553d3
commit
3eacc3bfce
@ -36,9 +36,14 @@
|
||||
#define MSG_YES _UxGT("Oui")
|
||||
#define MSG_NO _UxGT("Non")
|
||||
#define MSG_BACK _UxGT("Retour")
|
||||
#define MSG_MEDIA_ABORTING _UxGT("Annulation...")
|
||||
#define MSG_MEDIA_INSERTED _UxGT("Média inséré")
|
||||
#define MSG_MEDIA_REMOVED _UxGT("Média retiré")
|
||||
#define MSG_MEDIA_RELEASED _UxGT("Média libéré")
|
||||
#define MSG_MEDIA_WAITING _UxGT("Attente média")
|
||||
#define MSG_MEDIA_READ_ERROR _UxGT("Err lecture média")
|
||||
#define MSG_MEDIA_USB_REMOVED _UxGT("USB débranché")
|
||||
#define MSG_MEDIA_USB_FAILED _UxGT("Erreur média USB")
|
||||
#define MSG_LCD_ENDSTOPS _UxGT("Butées")
|
||||
#define MSG_LCD_SOFT_ENDSTOPS _UxGT("Butées SW")
|
||||
#define MSG_MAIN _UxGT("Menu principal")
|
||||
@ -89,6 +94,7 @@
|
||||
#define MSG_LEVEL_BED _UxGT("Niveau du lit")
|
||||
#define MSG_LEVEL_CORNERS _UxGT("Niveau des coins")
|
||||
#define MSG_NEXT_CORNER _UxGT("Coin suivant")
|
||||
#define MSG_MESH_EDITOR _UxGT("Edition Maillage")
|
||||
#define MSG_EDIT_MESH _UxGT("Modifier maille")
|
||||
#define MSG_EDITING_STOPPED _UxGT("Arrêt édit. maillage")
|
||||
#define MSG_PROBING_MESH _UxGT("Mesure point")
|
||||
@ -110,6 +116,13 @@
|
||||
#define MSG_X_OFFSET _UxGT("Buse 2 X")
|
||||
#define MSG_Y_OFFSET _UxGT("Buse 2 Y")
|
||||
#define MSG_Z_OFFSET _UxGT("Buse 2 Z")
|
||||
#define MSG_G26_HEATING_BED _UxGT("G26 Chauffe lit")
|
||||
#define MSG_G26_HEATING_NOZZLE _UxGT("G26 Chauffe buse")
|
||||
#define MSG_G26_MANUAL_PRIME _UxGT("Amorce manuelle...")
|
||||
#define MSG_G26_FIXED_LENGTH _UxGT("Amorce longueur fixe")
|
||||
#define MSG_G26_PRIME_DONE _UxGT("Amorce terminée")
|
||||
#define MSG_G26_CANCELED _UxGT("G26 annulé")
|
||||
#define MSG_G26_LEAVING _UxGT("Sortie G26")
|
||||
#define MSG_UBL_DOING_G29 _UxGT("G29 en cours")
|
||||
#define MSG_UBL_UNHOMED _UxGT("Origine XYZ requise")
|
||||
#define MSG_UBL_TOOLS _UxGT("Outils UBL")
|
||||
@ -169,6 +182,7 @@
|
||||
#define MSG_UBL_NO_STORAGE _UxGT("Pas de mémoire")
|
||||
#define MSG_UBL_SAVE_ERROR _UxGT("Err: Enreg. UBL")
|
||||
#define MSG_UBL_RESTORE_ERROR _UxGT("Err: Ouvrir UBL")
|
||||
#define MSG_UBL_Z_OFFSET _UxGT("Z-Offset: ")
|
||||
#define MSG_UBL_Z_OFFSET_STOPPED _UxGT("Décal. Z arrêté")
|
||||
#define MSG_UBL_STEP_BY_STEP_MENU _UxGT("UBL Pas à pas")
|
||||
|
||||
@ -432,6 +446,7 @@
|
||||
#define MSG_DRIVE_STRENGTH _UxGT("Puiss. moteur ")
|
||||
#define MSG_DAC_PERCENT _UxGT("Driver %")
|
||||
#define MSG_DAC_EEPROM_WRITE _UxGT("DAC EEPROM sauv.")
|
||||
#define MSG_ERROR_TMC _UxGT("ERREUR CONNEXION TMC")
|
||||
|
||||
#define MSG_FILAMENT_CHANGE_HEADER_PAUSE _UxGT("IMPR. PAUSE")
|
||||
#define MSG_FILAMENT_CHANGE_HEADER_LOAD _UxGT("CHARGER FIL")
|
||||
|
Loading…
Reference in New Issue
Block a user