Sanity checks for FILAMENT_CHANGE_FEATURE and FILAMENT_RUNOUT_SCRIPT
This commit is contained in:
Scott Lahteine
parent
5ab7b91615
commit
4061fca1ad
@ -659,33 +659,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -244,14 +244,20 @@
|
||||
#error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
|
||||
#elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART)
|
||||
#error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
|
||||
#elif DISABLED(FILAMENT_CHANGE_FEATURE)
|
||||
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "FILAMENT_CHANGE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Filament Change with Extruder Runout Prevention
|
||||
*/
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE) && ENABLED(EXTRUDER_RUNOUT_PREVENT)
|
||||
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with FILAMENT_CHANGE_FEATURE."
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#if DISABLED(ULTIPANEL)
|
||||
#error "FILAMENT_CHANGE_FEATURE currently requires an LCD controller."
|
||||
#elif ENABLED(EXTRUDER_RUNOUT_PREVENT)
|
||||
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with FILAMENT_CHANGE_FEATURE."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -659,33 +659,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -659,33 +659,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -642,33 +642,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -659,33 +659,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -659,33 +659,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -659,33 +659,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -661,33 +661,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -661,33 +661,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -666,33 +666,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -661,33 +661,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -659,33 +659,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
@ -659,33 +659,38 @@
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
/**
|
||||
* Filament Change
|
||||
* Experimental filament change support.
|
||||
* Adds the GCode M600 for initiating filament change.
|
||||
*
|
||||
* Requires an LCD display.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define FILAMENT_CHANGE_FEATURE
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 3 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
|
||||
Loading…
Reference in New Issue
Block a user