diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
old mode 100755
new mode 100644
index 18ae826b8..bb4096acf
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
@@ -77,7 +77,7 @@
#define STRING_CONFIG_H_AUTHOR "(Creality CR-10)" // Who made the changes.
#define SHOW_BOOTSCREEN
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
-//#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
+#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
//
// *** VENDORS PLEASE READ *****************************************************
@@ -90,7 +90,7 @@
// boot image unmodified. For an example have a look at the bq Hephestos 2
// example configuration folder.
//
-//#define SHOW_CUSTOM_BOOTSCREEN
+#define SHOW_CUSTOM_BOOTSCREEN
// @section machine
@@ -703,7 +703,7 @@
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
// Use double touch for probing
-#define PROBE_DOUBLE_TOUCH
+//#define PROBE_DOUBLE_TOUCH
/**
* Z probes require clearance when deploying, stowing, and moving between
@@ -789,7 +789,7 @@
#define X_MIN_POS 0
#define Y_MIN_POS 0
#define Z_MIN_POS 0
-#define X_MAX_POS X_BED_SIZE
+#define X_MAX_POS X_BED_SIZE + 20
#define Y_MAX_POS Y_BED_SIZE
#define Z_MAX_POS 400
@@ -940,7 +940,7 @@
#define UBL_PROBE_PT_3_X 180
#define UBL_PROBE_PT_3_Y 20
- #define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ //#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#elif ENABLED(MESH_BED_LEVELING)
@@ -997,6 +997,7 @@
// - If stepper drivers time out, it will need X and Y homing again before Z homing.
// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
// - Prevent Z homing when the Z probe is outside bed area.
+//
//#define Z_SAFE_HOMING
#if ENABLED(Z_SAFE_HOMING)
@@ -1021,13 +1022,10 @@
// M500 - stores parameters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
-// Define this to enable EEPROM support
-#define EEPROM_SETTINGS
-
-#if ENABLED(EEPROM_SETTINGS)
- //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
- #define EEPROM_CHITCHAT // Print a report on M500. Please keep turned on.
-#endif
+//
+#define EEPROM_SETTINGS // Enable for M500 and M501 commands
+//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
+#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
//
// Host Keepalive
@@ -1057,7 +1055,7 @@
// @section temperature
// Preheat Constants
-#define PREHEAT_1_TEMP_HOTEND 200
+#define PREHEAT_1_TEMP_HOTEND 190
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
@@ -1160,7 +1158,7 @@
* M76 - Pause the print job timer
* M77 - Stop the print job timer
*/
-//#define PRINTJOB_TIMER_AUTOSTART
+#define PRINTJOB_TIMER_AUTOSTART
/**
* Print Counter
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
new file mode 100644
index 000000000..3ded52305
--- /dev/null
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@@ -0,0 +1,1413 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
+#ifndef CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H_VERSION 020000
+
+// @section temperature
+
+//===========================================================================
+//=============================Thermal Settings ============================
+//===========================================================================
+
+#if DISABLED(PIDTEMPBED)
+ #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
+ #if ENABLED(BED_LIMIT_SWITCHING)
+ #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
+ #endif
+#endif
+
+/**
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
+ */
+#if ENABLED(THERMAL_PROTECTION_HOTENDS)
+ #define THERMAL_PROTECTION_PERIOD 40 // Seconds
+ #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
+
+ /**
+ * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
+ * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+ * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
+ * but only if the current temperature is far enough below the target for a reliable test.
+ *
+ * If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE
+ * WATCH_TEMP_INCREASE should not be below 2.
+ */
+ #define WATCH_TEMP_PERIOD 20 // Seconds
+ #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
+#endif
+
+/**
+ * Thermal Protection parameters for the bed are just as above for hotends.
+ */
+#if ENABLED(THERMAL_PROTECTION_BED)
+ #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
+ #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
+
+ /**
+ * Whenever an M140 or M190 increases the target temperature the firmware will wait for the
+ * WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE
+ * degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190,
+ * but only if the current temperature is far enough below the target for a reliable test.
+ *
+ * If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease
+ * WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.)
+ */
+ #define WATCH_BED_TEMP_PERIOD 60 // Seconds
+ #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
+#endif
+
+#if ENABLED(PIDTEMP)
+ // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
+ // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ //#define PID_EXTRUSION_SCALING
+ #if ENABLED(PID_EXTRUSION_SCALING)
+ #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
+ #define LPQ_MAX_LEN 50
+ #endif
+#endif
+
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S B F
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by executing M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
+#define AUTOTEMP
+#if ENABLED(AUTOTEMP)
+ #define AUTOTEMP_OLDWEIGHT 0.98
+#endif
+
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
+//#define SHOW_TEMP_ADC_VALUES
+
+/**
+ * High Temperature Thermistor Support
+ *
+ * Thermistors able to support high temperature tend to have a hard time getting
+ * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
+ * will probably be caught when the heating element first turns on during the
+ * preheating process, which will trigger a min_temp_error as a safety measure
+ * and force stop everything.
+ * To circumvent this limitation, we allow for a preheat time (during which,
+ * min_temp_error won't be triggered) and add a min_temp buffer to handle
+ * aberrant readings.
+ *
+ * If you want to enable this feature for your hotend thermistor(s)
+ * uncomment and set values > 0 in the constants below
+ */
+
+// The number of consecutive low temperature errors that can occur
+// before a min_temp_error is triggered. (Shouldn't be more than 10.)
+//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
+
+// The number of milliseconds a hotend will preheat before starting to check
+// the temperature. This value should NOT be set to the time it takes the
+// hot end to reach the target temperature, but the time it takes to reach
+// the minimum temperature your thermistor can read. The lower the better/safer.
+// This shouldn't need to be more than 30 seconds (30000)
+//#define MILLISECONDS_PREHEAT_TIME 0
+
+// @section extruder
+
+// Extruder runout prevention.
+// If the machine is idle and the temperature over MINTEMP
+// then extrude some filament every couple of SECONDS.
+//#define EXTRUDER_RUNOUT_PREVENT
+#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
+ #define EXTRUDER_RUNOUT_MINTEMP 190
+ #define EXTRUDER_RUNOUT_SECONDS 30
+ #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
+ #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
+#endif
+
+// @section temperature
+
+//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
+//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
+#define TEMP_SENSOR_AD595_OFFSET 0.0
+#define TEMP_SENSOR_AD595_GAIN 1.0
+
+/**
+ * Controller Fan
+ * To cool down the stepper drivers and MOSFETs.
+ *
+ * The fan will turn on automatically whenever any stepper is enabled
+ * and turn off after a set period after all steppers are turned off.
+ */
+//#define USE_CONTROLLER_FAN
+#if ENABLED(USE_CONTROLLER_FAN)
+ //#define CONTROLLER_FAN_PIN FAN1_PIN // Set a custom pin for the controller fan
+ #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
+ #define CONTROLLERFAN_SPEED 255 // 255 == full speed
+#endif
+
+// When first starting the main fan, run it at full speed for the
+// given number of milliseconds. This gets the fan spinning reliably
+// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
+//#define FAN_KICKSTART_TIME 100
+
+// This defines the minimal speed for the main fan, run in PWM mode
+// to enable uncomment and set minimal PWM speed for reliable running (1-255)
+// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+//#define FAN_MIN_PWM 50
+
+// @section extruder
+
+/**
+ * Extruder cooling fans
+ *
+ * Extruder auto fans automatically turn on when their extruders'
+ * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
+ *
+ * Your board's pins file specifies the recommended pins. Override those here
+ * or set to -1 to disable completely.
+ *
+ * Multiple extruders can be assigned to the same pin in which case
+ * the fan will turn on when any selected extruder is above the threshold.
+ */
+#define E0_AUTO_FAN_PIN -1
+#define E1_AUTO_FAN_PIN -1
+#define E2_AUTO_FAN_PIN -1
+#define E3_AUTO_FAN_PIN -1
+#define E4_AUTO_FAN_PIN -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
+
+/**
+ * Part-Cooling Fan Multiplexer
+ *
+ * This feature allows you to digitally multiplex the fan output.
+ * The multiplexer is automatically switched at tool-change.
+ * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans.
+ */
+#define FANMUX0_PIN -1
+#define FANMUX1_PIN -1
+#define FANMUX2_PIN -1
+
+/**
+ * M355 Case Light on-off / brightness
+ */
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+ //#define CASE_LIGHT_PIN 4 // Override the default pin if needed
+ #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
+ #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
+ #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
+ //#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu
+#endif
+
+//===========================================================================
+//============================ Mechanical Settings ==========================
+//===========================================================================
+
+// @section homing
+
+// If you want endstops to stay on (by default) even when not homing
+// enable this option. Override at any time with M120, M121.
+//#define ENDSTOPS_ALWAYS_ON_DEFAULT
+
+// @section extras
+
+//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
+
+// Dual X Steppers
+// Uncomment this option to drive two X axis motors.
+// The next unused E driver will be assigned to the second X stepper.
+//#define X_DUAL_STEPPER_DRIVERS
+#if ENABLED(X_DUAL_STEPPER_DRIVERS)
+ // Set true if the two X motors need to rotate in opposite directions
+ #define INVERT_X2_VS_X_DIR true
+#endif
+
+// Dual Y Steppers
+// Uncomment this option to drive two Y axis motors.
+// The next unused E driver will be assigned to the second Y stepper.
+//#define Y_DUAL_STEPPER_DRIVERS
+#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
+ // Set true if the two Y motors need to rotate in opposite directions
+ #define INVERT_Y2_VS_Y_DIR true
+#endif
+
+// A single Z stepper driver is usually used to drive 2 stepper motors.
+// Uncomment this option to use a separate stepper driver for each Z axis motor.
+// The next unused E driver will be assigned to the second Z stepper.
+//#define Z_DUAL_STEPPER_DRIVERS
+
+#if ENABLED(Z_DUAL_STEPPER_DRIVERS)
+
+ // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+ // That way the machine is capable to align the bed during home, since both Z steppers are homed.
+ // There is also an implementation of M666 (software endstops adjustment) to this feature.
+ // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+ // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+ // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+ // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+ // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+ //#define Z_DUAL_ENDSTOPS
+
+ #if ENABLED(Z_DUAL_ENDSTOPS)
+ #define Z2_USE_ENDSTOP _XMAX_
+ #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // Use M666 to determine/test this value
+ #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
+// Enable this for dual x-carriage printers.
+// A dual x-carriage design has the advantage that the inactive extruder can be parked which
+// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
+// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
+//#define DUAL_X_CARRIAGE
+#if ENABLED(DUAL_X_CARRIAGE)
+ // Configuration for second X-carriage
+ // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
+ // the second x-carriage always homes to the maximum endstop.
+ #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
+ #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
+ #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
+ // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
+ // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
+ // without modifying the firmware (through the "M218 T1 X???" command).
+ // Remember: you should set the second extruder x-offset to 0 in your slicer.
+
+ // There are a few selectable movement modes for dual x-carriages using M605 S
+ // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
+ // as long as it supports dual x-carriages. (M605 S0)
+ // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
+ // that additional slicer support is not required. (M605 S1)
+ // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
+ // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
+ // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
+
+ // This is the default power-up mode which can be later using M605.
+ #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE
+
+ // Default settings in "Auto-park Mode"
+ #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
+ #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
+
+ // Default x offset in duplication mode (typically set to half print bed width)
+ #define DEFAULT_DUPLICATION_X_OFFSET 100
+
+#endif // DUAL_X_CARRIAGE
+
+// Activate a solenoid on the active extruder with M380. Disable all with M381.
+// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
+//#define EXT_SOLENOID
+
+// @section homing
+
+//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+#define X_HOME_BUMP_MM 5
+#define Y_HOME_BUMP_MM 5
+#define Z_HOME_BUMP_MM 2
+#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
+#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
+
+// When G28 is called, this option will make Y home before X
+//#define HOME_Y_BEFORE_X
+
+// @section machine
+
+#define AXIS_RELATIVE_MODES {false, false, false, false}
+
+// Allow duplication mode with a basic dual-nozzle extruder
+//#define DUAL_NOZZLE_DUPLICATION_MODE
+
+// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
+#define INVERT_X_STEP_PIN false
+#define INVERT_Y_STEP_PIN false
+#define INVERT_Z_STEP_PIN false
+#define INVERT_E_STEP_PIN false
+
+// Default stepper release if idle. Set to 0 to deactivate.
+// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
+// Time can be set by M18 and M84.
+#define DEFAULT_STEPPER_DEACTIVE_TIME 120
+#define DISABLE_INACTIVE_X true
+#define DISABLE_INACTIVE_Y true
+#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_E true
+
+#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
+#define DEFAULT_MINTRAVELFEEDRATE 0.0
+
+//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
+
+// @section lcd
+
+#if ENABLED(ULTIPANEL)
+ #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+ #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
+#endif
+
+// @section extras
+
+// minimum time in microseconds that a movement needs to take if the buffer is emptied.
+#define DEFAULT_MINSEGMENTTIME 20000
+
+// If defined the movements slow down when the look ahead buffer is only half full
+#define SLOWDOWN
+
+// Frequency limit
+// See nophead's blog for more info
+// Not working O
+//#define XY_FREQUENCY_LIMIT 15
+
+// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
+// of the buffer and all stops. This should not be much greater than zero and should only be changed
+// if unwanted behavior is observed on a user's machine when running at very slow speeds.
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+
+// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
+#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
+
+/**
+ * @section stepper motor current
+ *
+ * Some boards have a means of setting the stepper motor current via firmware.
+ *
+ * The power on motor currents are set by:
+ * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
+ * known compatible chips: A4982
+ * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
+ * known compatible chips: AD5206
+ * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
+ * known compatible chips: MCP4728
+ * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
+ * known compatible chips: MCP4451, MCP4018
+ *
+ * Motor currents can also be set by M907 - M910 and by the LCD.
+ * M907 - applies to all.
+ * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
+ * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
+ */
+//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
+//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
+
+// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
+//#define DIGIPOT_I2C
+//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster
+#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
+// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
+#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
+#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
+
+//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
+#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
+
+// @section lcd
+
+// Include a page of printer information in the LCD Main Menu
+//#define LCD_INFO_MENU
+
+// Scroll a longer status message into view
+#define STATUS_MESSAGE_SCROLLING
+
+// On the Info Screen, display XY with one decimal place when possible
+//#define LCD_DECIMAL_SMALL_XY
+
+// The timeout (in ms) to return to the status screen from sub-menus
+//#define LCD_TIMEOUT_TO_STATUS 15000
+
+#if ENABLED(SDSUPPORT)
+
+ // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
+ // around this by connecting a push button or single throw switch to the pin defined
+ // as SD_DETECT_PIN in your board's pins definitions.
+ // This setting should be disabled unless you are using a push button, pulling the pin to ground.
+ // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
+ #define SD_DETECT_INVERTED
+
+ #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
+ #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+
+ #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
+ // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
+ // using:
+ //#define MENU_ADDAUTOSTART
+
+ /**
+ * Sort SD file listings in alphabetical order.
+ *
+ * With this option enabled, items on SD cards will be sorted
+ * by name for easier navigation.
+ *
+ * By default...
+ *
+ * - Use the slowest -but safest- method for sorting.
+ * - Folders are sorted to the top.
+ * - The sort key is statically allocated.
+ * - No added G-code (M34) support.
+ * - 40 item sorting limit. (Items after the first 40 are unsorted.)
+ *
+ * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
+ * compiler to calculate the worst-case usage and throw an error if the SRAM
+ * limit is exceeded.
+ *
+ * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
+ * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
+ * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
+ * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
+ */
+ #define SDCARD_SORT_ALPHA
+
+ // SD Card Sorting options
+ #if ENABLED(SDCARD_SORT_ALPHA)
+ #define SDSORT_LIMIT 256 // Maximum number of sorted items (10-256). Costs 27 bytes each.
+ #define FOLDER_SORTING -1 // -1=above 0=none 1=below
+ #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
+ #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting.
+ #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
+ #define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option.
+ #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
+ #endif
+
+ // Show a progress bar on HD44780 LCDs for SD printing
+ //#define LCD_PROGRESS_BAR
+
+ #if ENABLED(LCD_PROGRESS_BAR)
+ // Amount of time (ms) to show the bar
+ #define PROGRESS_BAR_BAR_TIME 2000
+ // Amount of time (ms) to show the status message
+ #define PROGRESS_BAR_MSG_TIME 3000
+ // Amount of time (ms) to retain the status message (0=forever)
+ #define PROGRESS_MSG_EXPIRE 0
+ // Enable this to show messages for MSG_TIME then hide them
+ //#define PROGRESS_MSG_ONCE
+ // Add a menu item to test the progress bar:
+ //#define LCD_PROGRESS_BAR_TEST
+ #endif
+
+ // This allows hosts to request long names for files and folders with M33
+ //#define LONG_FILENAME_HOST_SUPPORT
+
+ // This option allows you to abort SD printing when any endstop is triggered.
+ // This feature must be enabled with "M540 S1" or from the LCD menu.
+ // To have any effect, endstops must be enabled during SD printing.
+ //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
+
+#endif // SDSUPPORT
+
+/**
+ * Additional options for Graphical Displays
+ *
+ * Use the optimizations here to improve printing performance,
+ * which can be adversely affected by graphical display drawing,
+ * especially when doing several short moves, and when printing
+ * on DELTA and SCARA machines.
+ *
+ * Some of these options may result in the display lagging behind
+ * controller events, as there is a trade-off between reliable
+ * printing performance versus fast display updates.
+ */
+#if ENABLED(DOGLCD)
+ // Enable to save many cycles by drawing a hollow frame on the Info Screen
+ #define XYZ_HOLLOW_FRAME
+
+ // Enable to save many cycles by drawing a hollow frame on Menu Screens
+ #define MENU_HOLLOW_FRAME
+
+ // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
+ // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
+ //#define USE_BIG_EDIT_FONT
+
+ // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
+ // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
+ //#define USE_SMALL_INFOFONT
+
+ // Enable this option and reduce the value to optimize screen updates.
+ // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
+ //#define DOGM_SPI_DELAY_US 5
+#endif // DOGLCD
+
+// @section safety
+
+// The hardware watchdog should reset the microcontroller disabling all outputs,
+// in case the firmware gets stuck and doesn't do temperature regulation.
+#define USE_WATCHDOG
+
+#if ENABLED(USE_WATCHDOG)
+ // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
+ // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
+ // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
+ //#define WATCHDOG_RESET_MANUAL
+#endif
+
+// @section lcd
+
+/**
+ * Babystepping enables movement of the axes by tiny increments without changing
+ * the current position values. This feature is used primarily to adjust the Z
+ * axis in the first layer of a print in real-time.
+ *
+ * Warning: Does not respect endstops!
+ */
+#define BABYSTEPPING
+#if ENABLED(BABYSTEPPING)
+ //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
+ #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
+ #define BABYSTEP_MULTIPLICATOR 10 // Babysteps are very small. Increase for faster motion.
+ //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+ #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
+ #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
+ // Note: Extra time may be added to mitigate controller latency.
+#endif
+
+// @section extruder
+
+// extruder advance constant (s2/mm3)
+//
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
+//
+// Hooke's law says: force = k * distance
+// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
+// so: v ^ 2 is proportional to number of steps we advance the extruder
+//#define ADVANCE
+
+#if ENABLED(ADVANCE)
+ #define EXTRUDER_ADVANCE_K .0
+ #define D_FILAMENT 2.85
+#endif
+
+/**
+ * Implementation of linear pressure control
+ *
+ * Assumption: advance = k * (delta velocity)
+ * K=0 means advance disabled.
+ * See Marlin documentation for calibration instructions.
+ */
+//#define LIN_ADVANCE
+
+#if ENABLED(LIN_ADVANCE)
+ #define LIN_ADVANCE_K 75
+
+ /**
+ * Some Slicers produce Gcode with randomly jumping extrusion widths occasionally.
+ * For example within a 0.4mm perimeter it may produce a single segment of 0.05mm width.
+ * While this is harmless for normal printing (the fluid nature of the filament will
+ * close this very, very tiny gap), it throws off the LIN_ADVANCE pressure adaption.
+ *
+ * For this case LIN_ADVANCE_E_D_RATIO can be used to set the extrusion:distance ratio
+ * to a fixed value. Note that using a fixed ratio will lead to wrong nozzle pressures
+ * if the slicer is using variable widths or layer heights within one print!
+ *
+ * This option sets the default E:D ratio at startup. Use `M900` to override this value.
+ *
+ * Example: `M900 W0.4 H0.2 D1.75`, where:
+ * - W is the extrusion width in mm
+ * - H is the layer height in mm
+ * - D is the filament diameter in mm
+ *
+ * Example: `M900 R0.0458` to set the ratio directly.
+ *
+ * Set to 0 to auto-detect the ratio based on given Gcode G1 print moves.
+ *
+ * Slic3r (including Průša Control) produces Gcode compatible with the automatic mode.
+ * Cura (as of this writing) may produce Gcode incompatible with the automatic mode.
+ */
+ #define LIN_ADVANCE_E_D_RATIO 0 // The calculated ratio (or 0) according to the formula W * H / ((D / 2) ^ 2 * PI)
+ // Example: 0.4 * 0.2 / ((1.75 / 2) ^ 2 * PI) = 0.033260135
+#endif
+
+// @section leveling
+
+// Default mesh area is an area with an inset margin on the print area.
+// Below are the macros that are used to define the borders for the mesh area,
+// made available here for specialized needs, ie dual extruder setup.
+#if ENABLED(MESH_BED_LEVELING)
+ #define MESH_MIN_X MESH_INSET
+ #define MESH_MAX_X (X_BED_SIZE - (MESH_INSET))
+ #define MESH_MIN_Y MESH_INSET
+ #define MESH_MAX_Y (Y_BED_SIZE - (MESH_INSET))
+#elif ENABLED(AUTO_BED_LEVELING_UBL)
+ #define UBL_MESH_MIN_X UBL_MESH_INSET
+ #define UBL_MESH_MAX_X (X_BED_SIZE - (UBL_MESH_INSET))
+ #define UBL_MESH_MIN_Y UBL_MESH_INSET
+ #define UBL_MESH_MAX_Y (Y_BED_SIZE - (UBL_MESH_INSET))
+
+ // If this is defined, the currently active mesh will be saved in the
+ // current slot on M500.
+ #define UBL_SAVE_ACTIVE_ON_M500
+#endif
+
+// @section extras
+
+//
+// G2/G3 Arc Support
+//
+//#define ARC_SUPPORT // Disable this feature to save ~3226 bytes
+#if ENABLED(ARC_SUPPORT)
+ #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
+ #define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
+ //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
+ //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
+#endif
+
+// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
+//#define BEZIER_CURVE_SUPPORT
+
+// G38.2 and G38.3 Probe Target
+// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+//#define G38_PROBE_TARGET
+#if ENABLED(G38_PROBE_TARGET)
+ #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
+#endif
+
+// Moves (or segments) with fewer steps than this will be joined with the next move
+#define MIN_STEPS_PER_SEGMENT 6
+
+// The minimum pulse width (in µs) for stepping a stepper.
+// Set this if you find stepping unreliable, or if using a very fast CPU.
+#define MINIMUM_STEPPER_PULSE 0 // (µs) The smallest stepper pulse allowed
+
+// @section temperature
+
+// Control heater 0 and heater 1 in parallel.
+//#define HEATERS_PARALLEL
+
+//===========================================================================
+//================================= Buffers =================================
+//===========================================================================
+
+// @section hidden
+
+// The number of linear motions that can be in the plan at any give time.
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
+#if ENABLED(SDSUPPORT)
+ #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
+#else
+ #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+#endif
+
+// @section serial
+
+// The ASCII buffer for serial input
+#define MAX_CMD_SIZE 96
+#define BUFSIZE 4
+
+// Transfer Buffer Size
+// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
+// To buffer a simple "ok" you need 4 bytes.
+// For ADVANCED_OK (M105) you need 32 bytes.
+// For debug-echo: 128 bytes for the optimal speed.
+// Other output doesn't need to be that speedy.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256]
+#define TX_BUFFER_SIZE 0
+
+// Enable an emergency-command parser to intercept certain commands as they
+// enter the serial receive buffer, so they cannot be blocked.
+// Currently handles M108, M112, M410
+// Does not work on boards using AT90USB (USBCON) processors!
+//#define EMERGENCY_PARSER
+
+// Bad Serial-connections can miss a received command by sending an 'ok'
+// Therefore some clients abort after 30 seconds in a timeout.
+// Some other clients start sending commands while receiving a 'wait'.
+// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
+//#define NO_TIMEOUTS 1000 // Milliseconds
+
+// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
+//#define ADVANCED_OK
+
+// @section extras
+
+/**
+ * Firmware-based and LCD-controlled retract
+ *
+ * Add G10 / G11 commands for automatic firmware-based retract / recover.
+ * Use M207 and M208 to define parameters for retract / recover.
+ *
+ * Use M209 to enable or disable auto-retract.
+ * With auto-retract enabled, all G1 E moves within the set range
+ * will be converted to firmware-based retract/recover moves.
+ *
+ * Be sure to turn off auto-retract during filament change.
+ *
+ * Note that M207 / M208 / M209 settings are saved to EEPROM.
+ *
+ */
+//#define FWRETRACT // ONLY PARTIALLY TESTED
+#if ENABLED(FWRETRACT)
+ #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
+ #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
+ #define RETRACT_LENGTH 3 // Default retract length (positive mm)
+ #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
+ #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)
+ #define RETRACT_ZLIFT 0 // Default retract Z-lift
+ #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering)
+ #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
+ #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s)
+ #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s)
+#endif
+
+/**
+ * Advanced Pause
+ * Experimental feature for filament change support and for parking the nozzle when paused.
+ * Adds the GCode M600 for initiating filament change.
+ * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+#define ADVANCED_PAUSE_FEATURE
+#if ENABLED(ADVANCED_PAUSE_FEATURE)
+ #define PAUSE_PARK_X_POS 3 // X position of hotend
+ #define PAUSE_PARK_Y_POS 297 // Y position of hotend
+ #define PAUSE_PARK_Z_ADD 5 // Z addition of hotend (lift)
+ #define PAUSE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+ #define PAUSE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
+ #define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+ #define PAUSE_PARK_RETRACT_LENGTH 4 // Initial retract in mm
+ // It is a short retract used immediately after print interrupt before move to filament exchange position
+ #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
+ #define FILAMENT_CHANGE_UNLOAD_LENGTH 420 // Unload filament length from hotend in mm
+ // Longer length for bowden printers to unload filament from whole bowden tube,
+ // shorter length for printers without bowden to unload filament from extruder only,
+ // 0 to disable unloading for manual unloading
+ #define FILAMENT_CHANGE_LOAD_FEEDRATE 8 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
+ // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+ // Short or zero length for printers without bowden where loading is not used
+ #define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
+ #define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
+ // 0 to disable for manual extrusion
+ // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+ // or until outcoming filament color is not clear for filament color change
+ #define PAUSE_PARK_NOZZLE_TIMEOUT 120 // Turn off nozzle if user doesn't change filament within this time limit in seconds
+ #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 3 // Number of alert beeps before printer goes quiet
+ #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
+ // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
+ #define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
+ #define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
+#endif
+
+// @section tmc
+
+/**
+ * Enable this section if you have TMC26X motor drivers.
+ * You will need to import the TMC26XStepper library into the Arduino IDE for this
+ * (https://github.com/trinamic/TMC26XStepper.git)
+ */
+//#define HAVE_TMCDRIVER
+
+#if ENABLED(HAVE_TMCDRIVER)
+
+ //#define X_IS_TMC
+ //#define X2_IS_TMC
+ //#define Y_IS_TMC
+ //#define Y2_IS_TMC
+ //#define Z_IS_TMC
+ //#define Z2_IS_TMC
+ //#define E0_IS_TMC
+ //#define E1_IS_TMC
+ //#define E2_IS_TMC
+ //#define E3_IS_TMC
+ //#define E4_IS_TMC
+
+ #define X_MAX_CURRENT 1000 // in mA
+ #define X_SENSE_RESISTOR 91 // in mOhms
+ #define X_MICROSTEPS 16 // number of microsteps
+
+ #define X2_MAX_CURRENT 1000
+ #define X2_SENSE_RESISTOR 91
+ #define X2_MICROSTEPS 16
+
+ #define Y_MAX_CURRENT 1000
+ #define Y_SENSE_RESISTOR 91
+ #define Y_MICROSTEPS 16
+
+ #define Y2_MAX_CURRENT 1000
+ #define Y2_SENSE_RESISTOR 91
+ #define Y2_MICROSTEPS 16
+
+ #define Z_MAX_CURRENT 1000
+ #define Z_SENSE_RESISTOR 91
+ #define Z_MICROSTEPS 16
+
+ #define Z2_MAX_CURRENT 1000
+ #define Z2_SENSE_RESISTOR 91
+ #define Z2_MICROSTEPS 16
+
+ #define E0_MAX_CURRENT 1000
+ #define E0_SENSE_RESISTOR 91
+ #define E0_MICROSTEPS 16
+
+ #define E1_MAX_CURRENT 1000
+ #define E1_SENSE_RESISTOR 91
+ #define E1_MICROSTEPS 16
+
+ #define E2_MAX_CURRENT 1000
+ #define E2_SENSE_RESISTOR 91
+ #define E2_MICROSTEPS 16
+
+ #define E3_MAX_CURRENT 1000
+ #define E3_SENSE_RESISTOR 91
+ #define E3_MICROSTEPS 16
+
+ #define E4_MAX_CURRENT 1000
+ #define E4_SENSE_RESISTOR 91
+ #define E4_MICROSTEPS 16
+
+#endif
+
+// @section TMC2130
+
+/**
+ * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
+ *
+ * You'll also need the TMC2130Stepper Arduino library
+ * (https://github.com/teemuatlut/TMC2130Stepper).
+ *
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * the hardware SPI interface on your board and define the required CS pins
+ * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ */
+//#define HAVE_TMC2130
+
+#if ENABLED(HAVE_TMC2130)
+
+ // CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
+ //#define X_IS_TMC2130
+ //#define X2_IS_TMC2130
+ //#define Y_IS_TMC2130
+ //#define Y2_IS_TMC2130
+ //#define Z_IS_TMC2130
+ //#define Z2_IS_TMC2130
+ //#define E0_IS_TMC2130
+ //#define E1_IS_TMC2130
+ //#define E2_IS_TMC2130
+ //#define E3_IS_TMC2130
+ //#define E4_IS_TMC2130
+
+ /**
+ * Stepper driver settings
+ */
+
+ #define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
+ #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
+ #define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
+
+ #define X_CURRENT 1000 // rms current in mA. Multiply by 1.41 for peak current.
+ #define X_MICROSTEPS 16 // 0..256
+
+ #define Y_CURRENT 1000
+ #define Y_MICROSTEPS 16
+
+ #define Z_CURRENT 1000
+ #define Z_MICROSTEPS 16
+
+ //#define X2_CURRENT 1000
+ //#define X2_MICROSTEPS 16
+
+ //#define Y2_CURRENT 1000
+ //#define Y2_MICROSTEPS 16
+
+ //#define Z2_CURRENT 1000
+ //#define Z2_MICROSTEPS 16
+
+ //#define E0_CURRENT 1000
+ //#define E0_MICROSTEPS 16
+
+ //#define E1_CURRENT 1000
+ //#define E1_MICROSTEPS 16
+
+ //#define E2_CURRENT 1000
+ //#define E2_MICROSTEPS 16
+
+ //#define E3_CURRENT 1000
+ //#define E3_MICROSTEPS 16
+
+ //#define E4_CURRENT 1000
+ //#define E4_MICROSTEPS 16
+
+ /**
+ * Use Trinamic's ultra quiet stepping mode.
+ * When disabled, Marlin will use spreadCycle stepping mode.
+ */
+ #define STEALTHCHOP
+
+ /**
+ * Let Marlin automatically control stepper current.
+ * This is still an experimental feature.
+ * Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
+ * then decrease current by CURRENT_STEP until temperature prewarn is cleared.
+ * Adjusting starts from X/Y/Z/E_CURRENT but will not increase over AUTO_ADJUST_MAX
+ * Relevant g-codes:
+ * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
+ * M906 S1 - Start adjusting current
+ * M906 S0 - Stop adjusting current
+ * M911 - Report stepper driver overtemperature pre-warn condition.
+ * M912 - Clear stepper driver overtemperature pre-warn condition flag.
+ */
+ //#define AUTOMATIC_CURRENT_CONTROL
+
+ #if ENABLED(AUTOMATIC_CURRENT_CONTROL)
+ #define CURRENT_STEP 50 // [mA]
+ #define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
+ #define REPORT_CURRENT_CHANGE
+ #endif
+
+ /**
+ * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
+ * This mode allows for faster movements at the expense of higher noise levels.
+ * STEALTHCHOP needs to be enabled.
+ * M913 X/Y/Z/E to live tune the setting
+ */
+ //#define HYBRID_THRESHOLD
+
+ #define X_HYBRID_THRESHOLD 100 // [mm/s]
+ #define X2_HYBRID_THRESHOLD 100
+ #define Y_HYBRID_THRESHOLD 100
+ #define Y2_HYBRID_THRESHOLD 100
+ #define Z_HYBRID_THRESHOLD 4
+ #define Z2_HYBRID_THRESHOLD 4
+ #define E0_HYBRID_THRESHOLD 30
+ #define E1_HYBRID_THRESHOLD 30
+ #define E2_HYBRID_THRESHOLD 30
+ #define E3_HYBRID_THRESHOLD 30
+ #define E4_HYBRID_THRESHOLD 30
+
+ /**
+ * Use stallGuard2 to sense an obstacle and trigger an endstop.
+ * You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
+ * If used along with STEALTHCHOP, the movement will be louder when homing. This is normal.
+ *
+ * X/Y_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
+ * Higher values make the system LESS sensitive.
+ * Lower value make the system MORE sensitive.
+ * Too low values can lead to false positives, while too high values will collide the axis without triggering.
+ * It is advised to set X/Y_HOME_BUMP_MM to 0.
+ * M914 X/Y to live tune the setting
+ */
+ //#define SENSORLESS_HOMING
+
+ #if ENABLED(SENSORLESS_HOMING)
+ #define X_HOMING_SENSITIVITY 19
+ #define Y_HOMING_SENSITIVITY 19
+ #endif
+
+ /**
+ * You can set your own advanced settings by filling in predefined functions.
+ * A list of available functions can be found on the library github page
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * Example:
+ * #define TMC2130_ADV() { \
+ * stepperX.diag0_temp_prewarn(1); \
+ * stepperX.interpolate(0); \
+ * }
+ */
+ #define TMC2130_ADV() { }
+
+#endif // HAVE_TMC2130
+
+// @section L6470
+
+/**
+ * Enable this section if you have L6470 motor drivers.
+ * You need to import the L6470 library into the Arduino IDE for this.
+ * (https://github.com/ameyer/Arduino-L6470)
+ */
+
+//#define HAVE_L6470DRIVER
+#if ENABLED(HAVE_L6470DRIVER)
+
+ //#define X_IS_L6470
+ //#define X2_IS_L6470
+ //#define Y_IS_L6470
+ //#define Y2_IS_L6470
+ //#define Z_IS_L6470
+ //#define Z2_IS_L6470
+ //#define E0_IS_L6470
+ //#define E1_IS_L6470
+ //#define E2_IS_L6470
+ //#define E3_IS_L6470
+ //#define E4_IS_L6470
+
+ #define X_MICROSTEPS 16 // number of microsteps
+ #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
+ #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
+ #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall
+
+ #define X2_MICROSTEPS 16
+ #define X2_K_VAL 50
+ #define X2_OVERCURRENT 2000
+ #define X2_STALLCURRENT 1500
+
+ #define Y_MICROSTEPS 16
+ #define Y_K_VAL 50
+ #define Y_OVERCURRENT 2000
+ #define Y_STALLCURRENT 1500
+
+ #define Y2_MICROSTEPS 16
+ #define Y2_K_VAL 50
+ #define Y2_OVERCURRENT 2000
+ #define Y2_STALLCURRENT 1500
+
+ #define Z_MICROSTEPS 16
+ #define Z_K_VAL 50
+ #define Z_OVERCURRENT 2000
+ #define Z_STALLCURRENT 1500
+
+ #define Z2_MICROSTEPS 16
+ #define Z2_K_VAL 50
+ #define Z2_OVERCURRENT 2000
+ #define Z2_STALLCURRENT 1500
+
+ #define E0_MICROSTEPS 16
+ #define E0_K_VAL 50
+ #define E0_OVERCURRENT 2000
+ #define E0_STALLCURRENT 1500
+
+ #define E1_MICROSTEPS 16
+ #define E1_K_VAL 50
+ #define E1_OVERCURRENT 2000
+ #define E1_STALLCURRENT 1500
+
+ #define E2_MICROSTEPS 16
+ #define E2_K_VAL 50
+ #define E2_OVERCURRENT 2000
+ #define E2_STALLCURRENT 1500
+
+ #define E3_MICROSTEPS 16
+ #define E3_K_VAL 50
+ #define E3_OVERCURRENT 2000
+ #define E3_STALLCURRENT 1500
+
+ #define E4_MICROSTEPS 16
+ #define E4_K_VAL 50
+ #define E4_OVERCURRENT 2000
+ #define E4_STALLCURRENT 1500
+
+#endif
+
+/**
+ * TWI/I2C BUS
+ *
+ * This feature is an EXPERIMENTAL feature so it shall not be used on production
+ * machines. Enabling this will allow you to send and receive I2C data from slave
+ * devices on the bus.
+ *
+ * ; Example #1
+ * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
+ * ; It uses multiple M260 commands with one B arg
+ * M260 A99 ; Target slave address
+ * M260 B77 ; M
+ * M260 B97 ; a
+ * M260 B114 ; r
+ * M260 B108 ; l
+ * M260 B105 ; i
+ * M260 B110 ; n
+ * M260 S1 ; Send the current buffer
+ *
+ * ; Example #2
+ * ; Request 6 bytes from slave device with address 0x63 (99)
+ * M261 A99 B5
+ *
+ * ; Example #3
+ * ; Example serial output of a M261 request
+ * echo:i2c-reply: from:99 bytes:5 data:hello
+ */
+
+// @section i2cbus
+
+//#define EXPERIMENTAL_I2CBUS
+#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
+
+// @section extras
+
+/**
+ * Spindle & Laser control
+ *
+ * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
+ * to set spindle speed, spindle direction, and laser power.
+ *
+ * SuperPid is a router/spindle speed controller used in the CNC milling community.
+ * Marlin can be used to turn the spindle on and off. It can also be used to set
+ * the spindle speed from 5,000 to 30,000 RPM.
+ *
+ * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
+ * hardware PWM pin for the speed control and a pin for the rotation direction.
+ *
+ * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
+ */
+//#define SPINDLE_LASER_ENABLE
+#if ENABLED(SPINDLE_LASER_ENABLE)
+
+ #define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
+ #define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
+ #define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
+ #define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
+ #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
+ #define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
+ #define SPINDLE_INVERT_DIR false
+ #define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
+
+ /**
+ * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
+ *
+ * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
+ * where PWM duty cycle varies from 0 to 255
+ *
+ * set the following for your controller (ALL MUST BE SET)
+ */
+
+ #define SPEED_POWER_SLOPE 118.4
+ #define SPEED_POWER_INTERCEPT 0
+ #define SPEED_POWER_MIN 5000
+ #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
+
+ //#define SPEED_POWER_SLOPE 0.3922
+ //#define SPEED_POWER_INTERCEPT 0
+ //#define SPEED_POWER_MIN 10
+ //#define SPEED_POWER_MAX 100 // 0-100%
+#endif
+
+/**
+ * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
+ */
+//#define PINS_DEBUGGING
+
+/**
+ * Auto-report temperatures with M155 S
+ */
+#define AUTO_REPORT_TEMPERATURES
+
+/**
+ * Include capabilities in M115 output
+ */
+#define EXTENDED_CAPABILITIES_REPORT
+
+/**
+ * Volumetric extrusion default state
+ * Activate to make volumetric extrusion the default method,
+ * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
+ *
+ * M200 D0 to disable, M200 Dn to set a new diameter.
+ */
+//#define VOLUMETRIC_DEFAULT_ON
+
+/**
+ * Enable this option for a leaner build of Marlin that removes all
+ * workspace offsets, simplifying coordinate transformations, leveling, etc.
+ *
+ * - M206 and M428 are disabled.
+ * - G92 will revert to its behavior from Marlin 1.0.
+ */
+#define NO_WORKSPACE_OFFSETS
+
+/**
+ * Set the number of proportional font spaces required to fill up a typical character space.
+ * This can help to better align the output of commands like `G29 O` Mesh Output.
+ *
+ * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
+ * Otherwise, adjust according to your client and font.
+ */
+#define PROPORTIONAL_FONT_RATIO 1.0
+
+/**
+ * Spend 28 bytes of SRAM to optimize the GCode parser
+ */
+#define FASTER_GCODE_PARSER
+
+/**
+ * User-defined menu items that execute custom GCode
+ */
+//#define CUSTOM_USER_MENUS
+#if ENABLED(CUSTOM_USER_MENUS)
+ #define USER_SCRIPT_DONE "M117 User Script Done"
+ #define USER_SCRIPT_AUDIBLE_FEEDBACK
+
+ #define USER_DESC_1 "Home & UBL Info"
+ #define USER_GCODE_1 "G28\nG29 W"
+
+ #define USER_DESC_2 "Preheat for PLA"
+ #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
+
+ #define USER_DESC_3 "Preheat for ABS"
+ #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+
+ #define USER_DESC_4 "Heat Bed/Home/Level"
+ #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+
+ #define USER_DESC_5 "Home & Info"
+ #define USER_GCODE_5 "G28\nM503"
+#endif
+
+/**
+ * Specify an action command to send to the host when the printer is killed.
+ * Will be sent in the form '//action:ACTION_ON_KILL', e.g. '//action:poweroff'.
+ * The host must be configured to handle the action command.
+ */
+//#define ACTION_ON_KILL "poweroff"
+
+//===========================================================================
+//====================== I2C Position Encoder Settings ======================
+//===========================================================================
+
+/**
+ * I2C position encoders for closed loop control.
+ * Developed by Chris Barr at Aus3D.
+ *
+ * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder
+ * Github: https://github.com/Aus3D/MagneticEncoder
+ *
+ * Supplier: http://aus3d.com.au/magnetic-encoder-module
+ * Alternative Supplier: http://reliabuild3d.com/
+ *
+ * Reilabuild encoders have been modified to improve reliability.
+ */
+
+//#define I2C_POSITION_ENCODERS
+#if ENABLED(I2C_POSITION_ENCODERS)
+
+ #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
+ // encoders supported currently.
+
+ #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
+ #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS.
+ #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
+ // I2CPE_ENC_TYPE_ROTARY.
+ #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
+ // 1mm poles. For linear encoders this is ticks / mm,
+ // for rotary encoders this is ticks / revolution.
+ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
+ // steps per full revolution (motor steps/rev * microstepping)
+ //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
+ #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_NONE // Type of error error correction.
+ #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
+ // printer will attempt to correct the error; errors
+ // smaller than this are ignored to minimize effects of
+ // measurement noise / latency (filter).
+
+ #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
+ #define I2CPE_ENC_2_AXIS Y_AXIS
+ #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
+ #define I2CPE_ENC_2_TICKS_UNIT 2048
+ //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
+ //#define I2CPE_ENC_2_INVERT
+ #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_NONE
+ #define I2CPE_ENC_2_EC_THRESH 0.10
+
+ #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
+ #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
+
+ #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
+ #define I2CPE_ENC_4_AXIS E_AXIS
+
+ #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
+ #define I2CPE_ENC_5_AXIS E_AXIS
+
+ // Default settings for encoders which are enabled, but without settings configured above.
+ #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
+ #define I2CPE_DEF_ENC_TICKS_UNIT 2048
+ #define I2CPE_DEF_TICKS_REV (16 * 200)
+ #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
+ #define I2CPE_DEF_EC_THRESH 0.1
+
+ //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
+ // axis after which the printer will abort. Comment out to
+ // disable abort behaviour.
+
+ #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
+ // for this amount of time (in ms) before the encoder
+ // is trusted again.
+
+ /**
+ * Position is checked every time a new command is executed from the buffer but during long moves,
+ * this setting determines the minimum update time between checks. A value of 100 works well with
+ * error rolling average when attempting to correct only for skips and not for vibration.
+ */
+ #define I2CPE_MIN_UPD_TIME_MS 100 // Minimum time in miliseconds between encoder checks.
+
+ // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+ #define I2CPE_ERR_ROLLING_AVERAGE
+
+#endif // I2C_POSITION_ENCODERS
+
+/**
+ * MAX7219 Debug Matrix
+ *
+ * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip, which can be used as a status
+ * display. Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
+ *
+ * Fully assembled MAX7219 boards can be found on the internet for under $2(US).
+ * For example, see https://www.ebay.com/sch/i.html?_nkw=332349290049
+ */
+//#define MAX7219_DEBUG
+#if ENABLED(MAX7219_DEBUG)
+ #define MAX7219_CLK_PIN 64 // 77 on Re-ARM // Configuration of the 3 pins to control the display
+ #define MAX7219_DIN_PIN 57 // 78 on Re-ARM
+ #define MAX7219_LOAD_PIN 44 // 79 on Re-ARM
+
+ /**
+ * Sample debug features
+ * If you add more debug displays, be careful to avoid conflicts!
+ */
+ #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
+ #define MAX7219_DEBUG_STEPPER_HEAD 3 // Show the stepper queue head position on this and the next LED matrix row
+ #define MAX7219_DEBUG_STEPPER_TAIL 5 // Show the stepper queue tail position on this and the next LED matrix row
+
+ #define MAX7219_DEBUG_STEPPER_QUEUE 0 // Show the current stepper queue depth on this and the next LED matrix row
+ // If you experience stuttering, reboots, etc. this option can reveal how
+ // tweaks made to the configuration are affecting the printer in real-time.
+#endif
+
+#endif // CONFIGURATION_ADV_H
diff --git a/Marlin/src/config/examples/Creality/CR-10/_Bootscreen.h b/Marlin/src/config/examples/Creality/CR-10/_Bootscreen.h
new file mode 100644
index 000000000..fdf09dec3
--- /dev/null
+++ b/Marlin/src/config/examples/Creality/CR-10/_Bootscreen.h
@@ -0,0 +1,100 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+
+/**
+ * Tongue-in-cheek placeholder for a more Marlin-specific bitmap
+ * The joke is that every "CR-10" has different branding!
+ * Made using The Gimp and...
+ * - http://www.digole.com/tools/PicturetoC_Hex_converter.php
+ */
+#include
+
+#define CUSTOM_BOOTSCREEN_TIMEOUT 2500
+#define CUSTOM_BOOTSCREEN_BMPWIDTH 54
+#define CUSTOM_BOOTSCREEN_BMPHEIGHT 64
+
+const unsigned char custom_start_bmp[] PROGMEM = {
+ 0x00, 0x00, 0x00, 0x01, 0xE0, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x3F, 0xF8, 0x00, 0x00,
+ 0x00, 0x00, 0x03, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0x0F, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0x3F, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0x7F, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0x7F, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x0F, 0xF0,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFD, 0xFF, 0xF8,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x1F, 0xFF, 0xFF, 0xFF, 0xFF, 0xF8,
+ 0x01, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xF0,
+ 0x07, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xC0,
+ 0x1F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00,
+ 0x7F, 0xFF, 0xFF, 0xFF, 0xFF, 0xC0, 0x00,
+ 0x7F, 0xFF, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x7F, 0xFC, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x1F, 0x80, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFE, 0x3F, 0xF8,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xF8,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xF8,
+ 0x00, 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xE0,
+ 0x00, 0x00, 0x7F, 0xFF, 0xFF, 0xFF, 0xC0,
+ 0x00, 0x00, 0x3F, 0xFF, 0xFF, 0xFE, 0x00,
+ 0x00, 0x00, 0x1F, 0xFF, 0xFF, 0xE0, 0x00,
+ 0x00, 0x00, 0x07, 0xFF, 0xFC, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x3F, 0x00, 0x00, 0x00
+};