Merge pull request #3956 from thinkyhead/rc_mbl_single_axis_fix

MBL: Keep active when homing single axes (#3750)

Marlin/Marlin_main.cpp

@@ -2644,8 +2644,16 @@ inline void gcode_G28() {
    * on again when homing all axis
    */
   #if ENABLED(MESH_BED_LEVELING)
-    uint8_t mbl_was_active = mbl.active;
+    float pre_home_z = MESH_HOME_SEARCH_Z;
-    mbl.active = false;
+    if (mbl.active()) {
+      // Save known Z position if already homed
+      if (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS]) {
+        pre_home_z = current_position[Z_AXIS];
+        pre_home_z += mbl.get_z(current_position[X_AXIS] - home_offset[X_AXIS],
+                                current_position[Y_AXIS] - home_offset[Y_AXIS]);
+      }
+      mbl.set_active(false);
+    }
   #endif
 
   setup_for_endstop_move();
@@ -2945,20 +2953,31 @@ inline void gcode_G28() {
 
   // Enable mesh leveling again
   #if ENABLED(MESH_BED_LEVELING)
-    if (mbl_was_active && home_all_axis) {
+    if (mbl.has_mesh()) {
-      current_position[Z_AXIS] = MESH_HOME_SEARCH_Z;
+      if (home_all_axis || (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && homeZ)) {
-      sync_plan_position();
+        current_position[Z_AXIS] = MESH_HOME_SEARCH_Z;
-      mbl.active = 1;
+        sync_plan_position();
-      #if ENABLED(MESH_G28_REST_ORIGIN)
+        mbl.set_active(true);
-        current_position[Z_AXIS] = 0.0;
+        #if ENABLED(MESH_G28_REST_ORIGIN)
-        set_destination_to_current();
+          current_position[Z_AXIS] = 0.0;
-        feedrate = homing_feedrate[Z_AXIS];
+          set_destination_to_current();
-        line_to_destination();
+          feedrate = homing_feedrate[Z_AXIS];
-        stepper.synchronize();
+          line_to_destination();
-      #endif
+          stepper.synchronize();
-      #if ENABLED(DEBUG_LEVELING_FEATURE)
+        #else
-        if (DEBUGGING(LEVELING)) DEBUG_POS("mbl_was_active", current_position);
+          current_position[Z_AXIS] = MESH_HOME_SEARCH_Z -
-      #endif
+            mbl.get_z(current_position[X_AXIS] - home_offset[X_AXIS],
+                      current_position[Y_AXIS] - home_offset[Y_AXIS]);
+        #endif
+      }
+      else if ((axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS]) && (homeX || homeY)) {
+        current_position[Z_AXIS] = pre_home_z;
+        sync_plan_position();
+        mbl.set_active(true);
+        current_position[Z_AXIS] = pre_home_z -
+          mbl.get_z(current_position[X_AXIS] - home_offset[X_AXIS],
+                    current_position[Y_AXIS] - home_offset[Y_AXIS]);
+      }
     }
   #endif
 
@@ -2978,7 +2997,7 @@ inline void gcode_G28() {
 
 #if ENABLED(MESH_BED_LEVELING)
 
-  enum MeshLevelingState { MeshReport, MeshStart, MeshNext, MeshSet, MeshSetZOffset };
+  enum MeshLevelingState { MeshReport, MeshStart, MeshNext, MeshSet, MeshSetZOffset, MeshReset };
 
   inline void _mbl_goto_xy(float x, float y) {
     saved_feedrate = feedrate;
@@ -3015,6 +3034,7 @@ inline void gcode_G28() {
    *  S2              Probe the next mesh point
    *  S3 Xn Yn Zn.nn  Manually modify a single point
    *  S4 Zn.nn        Set z offset. Positive away from bed, negative closer to bed.
+   *  S5              Reset and disable mesh
    *
    * The S0 report the points as below
    *
@@ -3028,8 +3048,8 @@ inline void gcode_G28() {
 
     static int probe_point = -1;
     MeshLevelingState state = code_seen('S') ? (MeshLevelingState)code_value_short() : MeshReport;
-    if (state < 0 || state > 4) {
+    if (state < 0 || state > 5) {
-      SERIAL_PROTOCOLLNPGM("S out of range (0-4).");
+      SERIAL_PROTOCOLLNPGM("S out of range (0-5).");
       return;
     }
 
@@ -3038,8 +3058,13 @@ inline void gcode_G28() {
 
     switch (state) {
       case MeshReport:
-        if (mbl.active) {
+        if (mbl.has_mesh()) {
-          SERIAL_PROTOCOLPGM("Num X,Y: ");
+          SERIAL_PROTOCOLPGM("State: ");
+          if (mbl.active())
+            SERIAL_PROTOCOLPGM("On");
+          else
+            SERIAL_PROTOCOLPGM("Off");
+          SERIAL_PROTOCOLPGM("\nNum X,Y: ");
           SERIAL_PROTOCOL(MESH_NUM_X_POINTS);
           SERIAL_PROTOCOLCHAR(',');
           SERIAL_PROTOCOL(MESH_NUM_Y_POINTS);
@@ -3100,7 +3125,7 @@ inline void gcode_G28() {
           // After recording the last point, activate the mbl and home
           SERIAL_PROTOCOLLNPGM("Mesh probing done.");
           probe_point = -1;
-          mbl.active = true;
+          mbl.set_has_mesh(true);
           enqueue_and_echo_commands_P(PSTR("G28"));
         }
         break;
@@ -3147,6 +3172,19 @@ inline void gcode_G28() {
           return;
         }
         mbl.z_offset = z;
+        break;
+
+      case MeshReset:
+        if (mbl.active()) {
+          current_position[Z_AXIS] +=
+            mbl.get_z(current_position[X_AXIS] - home_offset[X_AXIS],
+                      current_position[Y_AXIS] - home_offset[Y_AXIS]) - MESH_HOME_SEARCH_Z;
+          mbl.reset();
+          sync_plan_position();
+        }
+        else
+          mbl.reset();
+
     } // switch(state)
 
     report_current_position();
@@ -5944,7 +5982,7 @@ inline void gcode_M410() {
   /**
    * M420: Enable/Disable Mesh Bed Leveling
    */
-  inline void gcode_M420() { if (code_seen('S') && code_has_value()) mbl.active = !!code_value_short(); }
+  inline void gcode_M420() { if (code_seen('S') && code_has_value()) mbl.set_has_mesh(!!code_value_short()); }
 
   /**
    * M421: Set a single Mesh Bed Leveling Z coordinate
@@ -7335,7 +7373,7 @@ void clamp_to_software_endstops(float target[3]) {
 
 // This function is used to split lines on mesh borders so each segment is only part of one mesh area
 void mesh_buffer_line(float x, float y, float z, const float e, float feed_rate, const uint8_t& extruder, uint8_t x_splits = 0xff, uint8_t y_splits = 0xff) {
-  if (!mbl.active) {
+  if (!mbl.active()) {
     planner.buffer_line(x, y, z, e, feed_rate, extruder);
     set_current_to_destination();
     return;

Marlin/configuration_store.cpp

@@ -58,8 +58,8 @@
  *  188  M206 XYZ  home_offset (float x3)
  *
  * Mesh bed leveling:
- *  200  M420 S    active (bool)
+ *  200  M420 S    status (uint8)
- *  201            z_offset (float) (added in V23)
+ *  201            z_offset (float)
  *  205            mesh_num_x (uint8 as set in firmware)
  *  206            mesh_num_y (uint8 as set in firmware)
  *  207 G29 S3 XYZ z_values[][] (float x9, by default)
@@ -187,20 +187,21 @@ void Config_StoreSettings()  {
   EEPROM_WRITE_VAR(i, planner.max_e_jerk);
   EEPROM_WRITE_VAR(i, home_offset);
 
-  uint8_t mesh_num_x = 3;
-  uint8_t mesh_num_y = 3;
   #if ENABLED(MESH_BED_LEVELING)
     // Compile time test that sizeof(mbl.z_values) is as expected
     typedef char c_assert[(sizeof(mbl.z_values) == (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS) * sizeof(dummy)) ? 1 : -1];
-    mesh_num_x = MESH_NUM_X_POINTS;
+    uint8_t mesh_num_x = MESH_NUM_X_POINTS,
-    mesh_num_y = MESH_NUM_Y_POINTS;
+            mesh_num_y = MESH_NUM_Y_POINTS,
-    EEPROM_WRITE_VAR(i, mbl.active);
+            dummy_uint8 = mbl.status & _BV(MBL_STATUS_HAS_MESH_BIT);
+    EEPROM_WRITE_VAR(i, dummy_uint8);
     EEPROM_WRITE_VAR(i, mbl.z_offset);
     EEPROM_WRITE_VAR(i, mesh_num_x);
     EEPROM_WRITE_VAR(i, mesh_num_y);
     EEPROM_WRITE_VAR(i, mbl.z_values);
   #else
-    uint8_t dummy_uint8 = 0;
+    uint8_t mesh_num_x = 3,
+            mesh_num_y = 3,
+            dummy_uint8 = 0;
     dummy = 0.0f;
     EEPROM_WRITE_VAR(i, dummy_uint8);
     EEPROM_WRITE_VAR(i, dummy);
@@ -376,7 +377,7 @@ void Config_RetrieveSettings() {
     EEPROM_READ_VAR(i, mesh_num_x);
     EEPROM_READ_VAR(i, mesh_num_y);
     #if ENABLED(MESH_BED_LEVELING)
-      mbl.active = dummy_uint8;
+      mbl.status = dummy_uint8;
       mbl.z_offset = dummy;
       if (mesh_num_x == MESH_NUM_X_POINTS && mesh_num_y == MESH_NUM_Y_POINTS) {
         EEPROM_READ_VAR(i, mbl.z_values);
@@ -550,7 +551,7 @@ void Config_ResetDefault() {
   home_offset[X_AXIS] = home_offset[Y_AXIS] = home_offset[Z_AXIS] = 0;
 
   #if ENABLED(MESH_BED_LEVELING)
-    mbl.active = false;
+    mbl.reset();
   #endif
 
   #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@@ -729,7 +730,7 @@ void Config_PrintSettings(bool forReplay) {
       SERIAL_ECHOLNPGM("Mesh bed leveling:");
       CONFIG_ECHO_START;
     }
-    SERIAL_ECHOPAIR("  M420 S", mbl.active);
+    SERIAL_ECHOPAIR("  M420 S", mbl.has_mesh() ? 1 : 0);
     SERIAL_ECHOPAIR(" X", MESH_NUM_X_POINTS);
     SERIAL_ECHOPAIR(" Y", MESH_NUM_Y_POINTS);
     SERIAL_EOL;

Marlin/mesh_bed_leveling.cpp

@@ -29,7 +29,7 @@
   mesh_bed_leveling::mesh_bed_leveling() { reset(); }
 
   void mesh_bed_leveling::reset() {
-    active = 0;
+    status = MBL_STATUS_NONE;
     z_offset = 0;
     for (int8_t y = MESH_NUM_Y_POINTS; y--;)
       for (int8_t x = MESH_NUM_X_POINTS; x--;)

Marlin/mesh_bed_leveling.h

@@ -24,12 +24,14 @@
 
 #if ENABLED(MESH_BED_LEVELING)
 
+  enum MBLStatus { MBL_STATUS_NONE = 0, MBL_STATUS_HAS_MESH_BIT = 0, MBL_STATUS_ACTIVE_BIT = 1 };
+
   #define MESH_X_DIST ((MESH_MAX_X - (MESH_MIN_X))/(MESH_NUM_X_POINTS - 1))
   #define MESH_Y_DIST ((MESH_MAX_Y - (MESH_MIN_Y))/(MESH_NUM_Y_POINTS - 1))
 
   class mesh_bed_leveling {
   public:
-    bool active;
+    uint8_t status; // Has Mesh and Is Active bits
     float z_offset;
     float z_values[MESH_NUM_Y_POINTS][MESH_NUM_X_POINTS];
 
@@ -41,6 +43,11 @@
     static FORCE_INLINE float get_probe_y(int8_t i) { return MESH_MIN_Y + (MESH_Y_DIST) * i; }
     void set_z(const int8_t px, const int8_t py, const float z) { z_values[py][px] = z; }
 
+    bool active()                 { return TEST(status, MBL_STATUS_ACTIVE_BIT); }
+    void set_active(bool onOff)   { if (onOff) SBI(status, MBL_STATUS_ACTIVE_BIT); else CBI(status, MBL_STATUS_ACTIVE_BIT); }
+    bool has_mesh()               { return TEST(status, MBL_STATUS_HAS_MESH_BIT); }
+    void set_has_mesh(bool onOff) { if (onOff) SBI(status, MBL_STATUS_HAS_MESH_BIT); else CBI(status, MBL_STATUS_HAS_MESH_BIT); }
+
     inline void zigzag(int8_t index, int8_t &px, int8_t &py) {
       px = index % (MESH_NUM_X_POINTS);
       py = index / (MESH_NUM_X_POINTS);

Marlin/planner.cpp

@@ -539,7 +539,8 @@ void Planner::check_axes_activity() {
   while (block_buffer_tail == next_buffer_head) idle();
 
   #if ENABLED(MESH_BED_LEVELING)
-    if (mbl.active) z += mbl.get_z(x - home_offset[X_AXIS], y - home_offset[Y_AXIS]);
+    if (mbl.active()) 
+      z += mbl.get_z(x - home_offset[X_AXIS], y - home_offset[Y_AXIS]);
   #elif ENABLED(AUTO_BED_LEVELING_FEATURE)
     apply_rotation_xyz(bed_level_matrix, x, y, z);
   #endif
@@ -1120,7 +1121,8 @@ void Planner::check_axes_activity() {
 #endif // AUTO_BED_LEVELING_FEATURE || MESH_BED_LEVELING
   {
     #if ENABLED(MESH_BED_LEVELING)
-      if (mbl.active) z += mbl.get_z(x - home_offset[X_AXIS], y - home_offset[Y_AXIS]);
+      if (mbl.active())
+        z += mbl.get_z(x - home_offset[X_AXIS], y - home_offset[Y_AXIS]);
     #elif ENABLED(AUTO_BED_LEVELING_FEATURE)
       apply_rotation_xyz(bed_level_matrix, x, y, z);
     #endif

Marlin/ultralcd.cpp

@@ -970,7 +970,7 @@ void lcd_cooldown() {
           line_to_current(Z_AXIS);
           stepper.synchronize();
 
-          mbl.active = true;
+          mbl.set_has_mesh(true);
           enqueue_and_echo_commands_P(PSTR("G28"));
           lcd_return_to_status();
           //LCD_MESSAGEPGM(MSG_LEVEL_BED_DONE);