diff --git a/Marlin/src/gcode/config/M218.cpp b/Marlin/src/gcode/config/M218.cpp
index 8d12ef595..144abb289 100644
--- a/Marlin/src/gcode/config/M218.cpp
+++ b/Marlin/src/gcode/config/M218.cpp
@@ -38,26 +38,38 @@
 void GcodeSuite::M218() {
   if (get_target_extruder_from_command() || target_extruder == 0) return;
 
-  if (parser.seenval('X')) hotend_offset[X_AXIS][target_extruder] = parser.value_linear_units();
-  if (parser.seenval('Y')) hotend_offset[Y_AXIS][target_extruder] = parser.value_linear_units();
+  bool report = true;
+  if (parser.seenval('X')) {
+    hotend_offset[X_AXIS][target_extruder] = parser.value_linear_units();
+    report = false;
+  }
+  if (parser.seenval('Y')) {
+    hotend_offset[Y_AXIS][target_extruder] = parser.value_linear_units();
+    report = false;
+  }
 
   #if ENABLED(DUAL_X_CARRIAGE) || ENABLED(SWITCHING_NOZZLE) || ENABLED(PARKING_EXTRUDER)
-    if (parser.seenval('Z')) hotend_offset[Z_AXIS][target_extruder] = parser.value_linear_units();
+    if (parser.seenval('Z')) {
+      hotend_offset[Z_AXIS][target_extruder] = parser.value_linear_units();
+      report = false;
+    }
   #endif
 
-  SERIAL_ECHO_START();
-  SERIAL_ECHOPGM(MSG_HOTEND_OFFSET);
-  HOTEND_LOOP() {
-    SERIAL_CHAR(' ');
-    SERIAL_ECHO(hotend_offset[X_AXIS][e]);
-    SERIAL_CHAR(',');
-    SERIAL_ECHO(hotend_offset[Y_AXIS][e]);
-    #if ENABLED(DUAL_X_CARRIAGE) || ENABLED(SWITCHING_NOZZLE) || ENABLED(PARKING_EXTRUDER)
+  if (report) {
+    SERIAL_ECHO_START();
+    SERIAL_ECHOPGM(MSG_HOTEND_OFFSET);
+    HOTEND_LOOP() {
+      SERIAL_CHAR(' ');
+      SERIAL_ECHO(hotend_offset[X_AXIS][e]);
       SERIAL_CHAR(',');
-      SERIAL_ECHO(hotend_offset[Z_AXIS][e]);
-    #endif
+      SERIAL_ECHO(hotend_offset[Y_AXIS][e]);
+      #if ENABLED(DUAL_X_CARRIAGE) || ENABLED(SWITCHING_NOZZLE) || ENABLED(PARKING_EXTRUDER)
+        SERIAL_CHAR(',');
+        SERIAL_ECHO(hotend_offset[Z_AXIS][e]);
+      #endif
+    }
+    SERIAL_EOL();
   }
-  SERIAL_EOL();
 }
 
 #endif // HOTENDS > 1
diff --git a/Marlin/src/gcode/gcode.h b/Marlin/src/gcode/gcode.h
index e618dcf05..548987c96 100644
--- a/Marlin/src/gcode/gcode.h
+++ b/Marlin/src/gcode/gcode.h
@@ -161,7 +161,7 @@
  * M209 - Turn Automatic Retract Detection on/off: S<0|1> (For slicers that don't support G10/11). (Requires FWRETRACT)
           Every normal extrude-only move will be classified as retract depending on the direction.
  * M211 - Enable, Disable, and/or Report software endstops: S<0|1> (Requires MIN_SOFTWARE_ENDSTOPS or MAX_SOFTWARE_ENDSTOPS)
- * M218 - Set a tool offset: "M218 T<index> X<offset> Y<offset>". (Requires 2 or more extruders)
+ * M218 - Set/get a tool offset: "M218 T<index> X<offset> Y<offset>". (Requires 2 or more extruders)
  * M220 - Set Feedrate Percentage: "M220 S<percent>" (i.e., "FR" on the LCD)
  * M221 - Set Flow Percentage: "M221 S<percent>"
  * M226 - Wait until a pin is in a given state: "M226 P<pin> S<state>"