Support SWITCHING_NOZZLE with 2 servos (#13054)
This commit is contained in:
parent
3c88cac2e9
commit
5cfc1cdacc
@ -194,11 +194,12 @@
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
|
||||
// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -966,7 +966,13 @@ void setup() {
|
||||
#endif
|
||||
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
move_nozzle_servo(0); // Initialize nozzle servo
|
||||
// Initialize nozzle servo(s)
|
||||
#if SWITCHING_NOZZLE_TWO_SERVOS
|
||||
lower_nozzle(0);
|
||||
raise_nozzle(1);
|
||||
#else
|
||||
move_nozzle_servo(0);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(PARKING_EXTRUDER)
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -199,7 +199,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -199,7 +199,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -206,7 +206,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -199,7 +199,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -207,7 +207,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -239,7 +239,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -201,7 +201,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -202,7 +202,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -203,7 +203,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -218,7 +218,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -203,7 +203,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -199,7 +199,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -201,7 +201,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -229,7 +229,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -220,7 +220,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -218,7 +218,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -217,7 +217,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -213,7 +213,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -203,7 +203,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -202,7 +202,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -203,7 +203,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -198,7 +198,8 @@
|
||||
//#define SWITCHING_NOZZLE
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
#define SWITCHING_NOZZLE_SERVO_NR 0
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||||
//#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second
|
||||
#define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -426,6 +426,7 @@
|
||||
#define HOTEND_LOOP() for (int8_t e = 0; e < HOTENDS; e++)
|
||||
|
||||
#define DO_SWITCH_EXTRUDER (ENABLED(SWITCHING_EXTRUDER) && (DISABLED(SWITCHING_NOZZLE) || SWITCHING_EXTRUDER_SERVO_NR != SWITCHING_NOZZLE_SERVO_NR))
|
||||
#define SWITCHING_NOZZLE_TWO_SERVOS defined(SWITCHING_NOZZLE_E1_SERVO_NR)
|
||||
|
||||
#define HAS_HOTEND_OFFSET (HOTENDS > 1)
|
||||
|
||||
|
@ -702,6 +702,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||
#error "SWITCHING_NOZZLE requires exactly 2 EXTRUDERS."
|
||||
#elif NUM_SERVOS < 1
|
||||
#error "SWITCHING_NOZZLE requires NUM_SERVOS >= 1."
|
||||
#endif
|
||||
|
||||
#ifndef SWITCHING_NOZZLE_SERVO_NR
|
||||
#error "SWITCHING_NOZZLE requires SWITCHING_NOZZLE_SERVO_NR."
|
||||
#elif SWITCHING_NOZZLE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
|
||||
#error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE."
|
||||
#elif SWITCHING_NOZZLE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
|
||||
@ -711,6 +715,20 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||
#elif SWITCHING_NOZZLE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
|
||||
#error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE."
|
||||
#endif
|
||||
|
||||
#ifdef SWITCHING_NOZZLE_E1_SERVO_NR
|
||||
#if SWITCHING_NOZZLE_E1_SERVO_NR == SWITCHING_NOZZLE_SERVO_NR
|
||||
#error "SWITCHING_NOZZLE_E1_SERVO_NR must be different from SWITCHING_NOZZLE_SERVO_NR."
|
||||
#elif SWITCHING_NOZZLE_E1_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
|
||||
#error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE."
|
||||
#elif SWITCHING_NOZZLE_E1_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
|
||||
#error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE."
|
||||
#elif SWITCHING_NOZZLE_E1_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
|
||||
#error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE."
|
||||
#elif SWITCHING_NOZZLE_E1_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
|
||||
#error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE."
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -100,11 +100,30 @@
|
||||
#endif // DO_SWITCH_EXTRUDER
|
||||
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
void move_nozzle_servo(const uint8_t e) {
|
||||
planner.synchronize();
|
||||
MOVE_SERVO(SWITCHING_NOZZLE_SERVO_NR, servo_angles[SWITCHING_NOZZLE_SERVO_NR][e]);
|
||||
safe_delay(500);
|
||||
}
|
||||
|
||||
#if SWITCHING_NOZZLE_TWO_SERVOS
|
||||
|
||||
inline void _move_nozzle_servo(const uint8_t e, const uint8_t angle_index) {
|
||||
constexpr int8_t sns_index[2] = { SWITCHING_NOZZLE_SERVO_NR, SWITCHING_NOZZLE_E1_SERVO_NR };
|
||||
constexpr int16_t sns_angles[2] = SWITCHING_NOZZLE_SERVO_ANGLES;
|
||||
planner.synchronize();
|
||||
MOVE_SERVO(sns_index[e], sns_angles[angle_index]);
|
||||
safe_delay(500);
|
||||
}
|
||||
|
||||
void lower_nozzle(const uint8_t e) { _move_nozzle_servo(e, 0); }
|
||||
void raise_nozzle(const uint8_t e) { _move_nozzle_servo(e, 1); }
|
||||
|
||||
#else
|
||||
|
||||
void move_nozzle_servo(const uint8_t angle_index) {
|
||||
planner.synchronize();
|
||||
MOVE_SERVO(SWITCHING_NOZZLE_SERVO_NR, servo_angles[SWITCHING_NOZZLE_SERVO_NR][e]);
|
||||
safe_delay(500);
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
#endif // SWITCHING_NOZZLE
|
||||
|
||||
#if ENABLED(PARKING_EXTRUDER)
|
||||
@ -581,6 +600,11 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
|
||||
#endif // TOOLCHANGE_FILAMENT_SWAP
|
||||
|
||||
if (tmp_extruder != active_extruder) {
|
||||
|
||||
#if SWITCHING_NOZZLE_TWO_SERVOS
|
||||
raise_nozzle(active_extruder);
|
||||
#endif
|
||||
|
||||
const float old_feedrate_mm_s = fr_mm_s > 0.0 ? fr_mm_s : feedrate_mm_s;
|
||||
feedrate_mm_s = fr_mm_s > 0.0 ? fr_mm_s : XY_PROBE_FEEDRATE_MM_S;
|
||||
|
||||
@ -639,8 +663,9 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
|
||||
parking_extruder_tool_change(tmp_extruder, no_move);
|
||||
#elif ENABLED(SWITCHING_TOOLHEAD) // Switching Toolhead
|
||||
switching_toolhead_tool_change(tmp_extruder, fr_mm_s, no_move);
|
||||
#elif ENABLED(SWITCHING_NOZZLE)
|
||||
// Always raise by a configured distance to avoid workpiece
|
||||
#elif ENABLED(SWITCHING_NOZZLE) && !SWITCHING_NOZZLE_TWO_SERVOS
|
||||
// Raise by a configured distance to avoid workpiece, except with
|
||||
// SWITCHING_NOZZLE_TWO_SERVOS, as both nozzles will lift instead.
|
||||
current_position[Z_AXIS] += MAX(-zdiff, 0.0) + toolchange_settings.z_raise;
|
||||
#if HAS_SOFTWARE_ENDSTOPS
|
||||
NOMORE(current_position[Z_AXIS], soft_endstop_max[Z_AXIS]);
|
||||
@ -729,6 +754,9 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
|
||||
mmu2.toolChange(tmp_extruder);
|
||||
#endif
|
||||
|
||||
#if SWITCHING_NOZZLE_TWO_SERVOS
|
||||
lower_nozzle(active_extruder);
|
||||
#endif
|
||||
} // (tmp_extruder != active_extruder)
|
||||
|
||||
planner.synchronize();
|
||||
|
@ -45,7 +45,12 @@
|
||||
#endif
|
||||
|
||||
#if ENABLED(SWITCHING_NOZZLE)
|
||||
void move_nozzle_servo(const uint8_t e);
|
||||
#if SWITCHING_NOZZLE_TWO_SERVOS
|
||||
void lower_nozzle(const uint8_t e);
|
||||
void raise_nozzle(const uint8_t e);
|
||||
#else
|
||||
void move_nozzle_servo(const uint8_t angle_index);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(PARKING_EXTRUDER)
|
||||
|
@ -26,16 +26,17 @@ exec_test $1 $2 "Azteeg X5GT Example Config"
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_MKS_SBASE
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set NUM_SERVOS 1
|
||||
opt_enable SWITCHING_EXTRUDER ULTIMAKERCONTROLLER
|
||||
exec_test $1 $2 "MKS_SBASE SWITCHING_EXTRUDER"
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set NUM_SERVOS 2
|
||||
opt_set SERVO_DELAY "{ 300, 300 }"
|
||||
opt_enable SWITCHING_NOZZLE SWITCHING_NOZZLE_E1_SERVO_NR ULTIMAKERCONTROLLER
|
||||
exec_test $1 $2 "MKS_SBASE SWITCHING_NOZZLE"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EEB
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_0 1
|
||||
opt_set TEMP_SENSOR_1 5
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set TEMP_SENSOR_1 -1
|
||||
opt_set TEMP_SENSOR_BED 5
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
|
||||
FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY \
|
||||
FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
|
||||
|
Loading…
Reference in New Issue
Block a user