Rename some feedrate-oriented functions

Marlin/src/gcode/bedlevel/abl/G29.cpp

@@ -446,7 +446,7 @@ G29_TYPE GcodeSuite::G29() {
       }
     #endif
 
-    if (!faux) setup_for_endstop_or_probe_move();
+    if (!faux) remember_feedrate_scaling_off();
 
     #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
 
@@ -980,7 +980,7 @@ G29_TYPE GcodeSuite::G29() {
   } // !isnan(measured_z)
 
   // Restore state after probing
-  if (!faux) clean_up_after_endstop_or_probe_move();
+  if (!faux) restore_feedrate_and_scaling();
 
   if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("<<< G29");
 

Marlin/src/gcode/calibrate/G28.cpp

@@ -261,7 +261,7 @@ void GcodeSuite::G28(const bool always_home_all) {
     extruder_duplication_enabled = false;
   #endif
 
-  setup_for_endstop_or_probe_move();
+  remember_feedrate_scaling_off();
 
   endstops.enable(true); // Enable endstops for next homing move
 
@@ -427,7 +427,7 @@ void GcodeSuite::G28(const bool always_home_all) {
     set_bed_leveling_enabled(leveling_was_active);
   #endif
 
-  clean_up_after_endstop_or_probe_move();
+  restore_feedrate_and_scaling();
 
   // Restore the active tool after homing
   #if HOTENDS > 1 && (DISABLED(DELTA) || ENABLED(DELTA_HOME_TO_SAFE_ZONE))

Marlin/src/gcode/calibrate/G33.cpp

@@ -84,7 +84,7 @@ void ac_setup(const bool reset_bed) {
   #endif
 
   planner.synchronize();
-  setup_for_endstop_or_probe_move();
+  remember_feedrate_scaling_off();
 
   #if HAS_LEVELING
     if (reset_bed) reset_bed_level(); // After full calibration bed-level data is no longer valid
@@ -102,7 +102,7 @@ void ac_cleanup(
   #if HAS_BED_PROBE
     STOW_PROBE();
   #endif
-  clean_up_after_endstop_or_probe_move();
+  restore_feedrate_and_scaling();
   #if HOTENDS > 1
     tool_change(old_tool_index, true);
   #endif

Marlin/src/gcode/calibrate/M48.cpp

@@ -111,7 +111,7 @@ void GcodeSuite::M48() {
     set_bed_leveling_enabled(false);
   #endif
 
-  setup_for_endstop_or_probe_move();
+  remember_feedrate_scaling_off();
 
   float mean = 0.0, sigma = 0.0, min = 99999.9, max = -99999.9, sample_set[n_samples];
 
@@ -256,7 +256,7 @@ void GcodeSuite::M48() {
     #endif
   }
 
-  clean_up_after_endstop_or_probe_move();
+  restore_feedrate_and_scaling();
 
   // Re-enable bed level correction if it had been on
   #if HAS_LEVELING

Marlin/src/gcode/probe/G30.cpp

@@ -49,7 +49,7 @@ void GcodeSuite::G30() {
     set_bed_leveling_enabled(false);
   #endif
 
-  setup_for_endstop_or_probe_move();
+  remember_feedrate_scaling_off();
 
   const ProbePtRaise raise_after = parser.boolval('E', true) ? PROBE_PT_STOW : PROBE_PT_NONE;
   const float measured_z = probe_at_point(xpos, ypos, raise_after, 1);
@@ -57,7 +57,7 @@ void GcodeSuite::G30() {
   if (!isnan(measured_z))
     SERIAL_ECHOLNPAIR("Bed X: ", FIXFLOAT(xpos), " Y: ", FIXFLOAT(ypos), " Z: ", FIXFLOAT(measured_z));
 
-  clean_up_after_endstop_or_probe_move();
+  restore_feedrate_and_scaling();
 
   #ifdef Z_AFTER_PROBING
     if (raise_after == PROBE_PT_STOW) move_z_after_probing();

Marlin/src/gcode/probe/G38.cpp

@@ -109,7 +109,7 @@ void GcodeSuite::G38(const int8_t subcode) {
   // Get X Y Z E F
   get_destination_from_command();
 
-  setup_for_endstop_or_probe_move();
+  remember_feedrate_scaling_off();
 
   const bool error_on_fail =
     #if ENABLED(G38_PROBE_AWAY)
@@ -128,7 +128,7 @@ void GcodeSuite::G38(const int8_t subcode) {
       break;
     }
 
-  clean_up_after_endstop_or_probe_move();
+  restore_feedrate_and_scaling();
 }
 
 #endif // G38_PROBE_TARGET

Marlin/src/module/motion.cpp

@@ -439,12 +439,15 @@ void do_blocking_move_to_xy(const float &rx, const float &ry, const float &fr_mm
 //
 static float saved_feedrate_mm_s;
 static int16_t saved_feedrate_percentage;
-void setup_for_endstop_or_probe_move() {
+void remember_feedrate_and_scaling() {
   saved_feedrate_mm_s = feedrate_mm_s;
   saved_feedrate_percentage = feedrate_percentage;
+}
+void remember_feedrate_scaling_off() {
+  remember_feedrate_and_scaling();
   feedrate_percentage = 100;
 }
-void clean_up_after_endstop_or_probe_move() {
+void restore_feedrate_and_scaling() {
   feedrate_mm_s = saved_feedrate_mm_s;
   feedrate_percentage = saved_feedrate_percentage;
 }

Marlin/src/module/motion.h

@@ -203,8 +203,9 @@ FORCE_INLINE void do_blocking_move_to(const float (&raw)[XYZE], const float &fr_
   do_blocking_move_to(raw[X_AXIS], raw[Y_AXIS], raw[Z_AXIS], fr_mm_s);
 }
 
-void setup_for_endstop_or_probe_move();
-void clean_up_after_endstop_or_probe_move();
+void remember_feedrate_and_scaling();
+void remember_feedrate_scaling_off();
+void restore_feedrate_and_scaling();
 
 //
 // Homing