Fix M217 report label, general cleanup
This commit is contained in:
parent
fae2b7edc3
commit
5e38d70697
@ -30,7 +30,7 @@
|
|||||||
void M217_report(const bool eeprom=false) {
|
void M217_report(const bool eeprom=false) {
|
||||||
|
|
||||||
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
|
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
|
||||||
serialprintPGM(eeprom ? PSTR(" M217") : PSTR("Singlenozzle:"));
|
serialprintPGM(eeprom ? PSTR(" M217") : PSTR("Toolchange:"));
|
||||||
SERIAL_ECHOPAIR(" S", LINEAR_UNIT(toolchange_settings.swap_length));
|
SERIAL_ECHOPAIR(" S", LINEAR_UNIT(toolchange_settings.swap_length));
|
||||||
SERIAL_ECHOPAIR(" P", LINEAR_UNIT(toolchange_settings.prime_speed));
|
SERIAL_ECHOPAIR(" P", LINEAR_UNIT(toolchange_settings.prime_speed));
|
||||||
SERIAL_ECHOPAIR(" R", LINEAR_UNIT(toolchange_settings.retract_speed));
|
SERIAL_ECHOPAIR(" R", LINEAR_UNIT(toolchange_settings.retract_speed));
|
||||||
|
@ -903,12 +903,12 @@
|
|||||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||||
*/
|
*/
|
||||||
#define Z_CLEARANCE_DEPLOY_PROBE 0 // Z Clearance for Deploy/Stow
|
#define Z_CLEARANCE_DEPLOY_PROBE 0 // Z Clearance for Deploy/Stow
|
||||||
#define Z_CLEARANCE_BETWEEN_PROBES 2 // Z Clearance between probe points
|
#define Z_CLEARANCE_BETWEEN_PROBES 2 // Z Clearance between probe points
|
||||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||||
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||||
|
|
||||||
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
|
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
|
||||||
|
|
||||||
// For M851 give a range for adjusting the Z probe offset
|
// For M851 give a range for adjusting the Z probe offset
|
||||||
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
||||||
|
@ -1116,9 +1116,6 @@
|
|||||||
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS
|
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS
|
||||||
#define Z_MAX_POS MANUAL_Z_HOME_POS
|
#define Z_MAX_POS MANUAL_Z_HOME_POS
|
||||||
|
|
||||||
// Z raise distance for tool-change, as needed for some extruders
|
|
||||||
#define TOOLCHANGE_ZRAISE 2 // (mm)
|
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Software Endstops
|
* Software Endstops
|
||||||
*
|
*
|
||||||
|
Loading…
Reference in New Issue
Block a user