Clean up digital pots and microsteps

Marlin/Conditionals_post.h

@@ -462,10 +462,13 @@
   #define HAS_SOLENOID_1 (PIN_EXISTS(SOL1))
   #define HAS_SOLENOID_2 (PIN_EXISTS(SOL2))
   #define HAS_SOLENOID_3 (PIN_EXISTS(SOL3))
-  #define HAS_MICROSTEPS (PIN_EXISTS(X_MS1))
+  #define HAS_MICROSTEPS_X (PIN_EXISTS(X_MS1))
+  #define HAS_MICROSTEPS_Y (PIN_EXISTS(Y_MS1))
+  #define HAS_MICROSTEPS_Z (PIN_EXISTS(Z_MS1))
   #define HAS_MICROSTEPS_E0 (PIN_EXISTS(E0_MS1))
   #define HAS_MICROSTEPS_E1 (PIN_EXISTS(E1_MS1))
   #define HAS_MICROSTEPS_E2 (PIN_EXISTS(E2_MS1))
+  #define HAS_MICROSTEPS (HAS_MICROSTEPS_X || HAS_MICROSTEPS_Y || HAS_MICROSTEPS_Z || HAS_MICROSTEPS_E0 || HAS_MICROSTEPS_E1 || HAS_MICROSTEPS_E2)
   #define HAS_STEPPER_RESET (PIN_EXISTS(STEPPER_RESET))
   #define HAS_X_ENABLE (PIN_EXISTS(X_ENABLE))
   #define HAS_X2_ENABLE (PIN_EXISTS(X2_ENABLE))

Marlin/Marlin_main.cpp

@@ -6517,7 +6517,7 @@ inline void gcode_M907() {
     if (code_seen(axis_codes[i])) stepper.digipot_current(i, code_value_int());
     if (code_seen('B')) stepper.digipot_current(4, code_value_int());
     if (code_seen('S')) for (int i = 0; i <= 4; i++) stepper.digipot_current(i, code_value_int());
-  #endif
+  #elif HAS_MOTOR_CURRENT_PWM
     #if PIN_EXISTS(MOTOR_CURRENT_PWM_XY)
       if (code_seen('X')) stepper.digipot_current(0, code_value_int());
     #endif
@@ -6527,6 +6527,7 @@ inline void gcode_M907() {
     #if PIN_EXISTS(MOTOR_CURRENT_PWM_E)
       if (code_seen('E')) stepper.digipot_current(2, code_value_int());
     #endif
+  #endif
   #if ENABLED(DIGIPOT_I2C)
     // this one uses actual amps in floating point
     LOOP_XYZE(i) if (code_seen(axis_codes[i])) digipot_i2c_set_current(i, code_value_float());

Marlin/stepper.cpp

@@ -733,19 +733,27 @@ void Stepper::isr() {
 
 void Stepper::init() {
 
-  digipot_init(); //Initialize Digipot Motor Current
+  // Init Digipot Motor Current
-  microstep_init(); //Initialize Microstepping Pins
+  #if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM
+    digipot_init();
+  #endif
 
-  // initialise TMC Steppers
+  // Init Microstepping Pins
+  #if HAS_MICROSTEPS
+    microstep_init();
+  #endif
+
+  // Init TMC Steppers
   #if ENABLED(HAVE_TMCDRIVER)
     tmc_init();
   #endif
-    // initialise L6470 Steppers
+
+  // Init L6470 Steppers
   #if ENABLED(HAVE_L6470DRIVER)
     L6470_init();
   #endif
 
-  // Initialize Dir Pins
+  // Init Dir Pins
   #if HAS_X_DIR
     X_DIR_INIT;
   #endif
@@ -777,8 +785,7 @@ void Stepper::init() {
     E3_DIR_INIT;
   #endif
 
-  //Initialize Enable Pins - steppers default to disabled.
+  // Init Enable Pins - steppers default to disabled.
-
   #if HAS_X_ENABLE
     X_ENABLE_INIT;
     if (!X_ENABLE_ON) X_ENABLE_WRITE(HIGH);
@@ -787,7 +794,6 @@ void Stepper::init() {
       if (!X_ENABLE_ON) X2_ENABLE_WRITE(HIGH);
     #endif
   #endif
-
   #if HAS_Y_ENABLE
     Y_ENABLE_INIT;
     if (!Y_ENABLE_ON) Y_ENABLE_WRITE(HIGH);
@@ -796,7 +802,6 @@ void Stepper::init() {
       if (!Y_ENABLE_ON) Y2_ENABLE_WRITE(HIGH);
     #endif
   #endif
-
   #if HAS_Z_ENABLE
     Z_ENABLE_INIT;
     if (!Z_ENABLE_ON) Z_ENABLE_WRITE(HIGH);
@@ -805,7 +810,6 @@ void Stepper::init() {
       if (!Z_ENABLE_ON) Z2_ENABLE_WRITE(HIGH);
     #endif
   #endif
-
   #if HAS_E0_ENABLE
     E0_ENABLE_INIT;
     if (!E_ENABLE_ON) E0_ENABLE_WRITE(HIGH);
@@ -823,9 +827,7 @@ void Stepper::init() {
     if (!E_ENABLE_ON) E3_ENABLE_WRITE(HIGH);
   #endif
 
-  //
+  // Init endstops and pullups
-  // Init endstops and pullups here
-  //
   endstops.init();
 
   #define _STEP_INIT(AXIS) AXIS ##_STEP_INIT
@@ -839,7 +841,7 @@ void Stepper::init() {
 
   #define E_AXIS_INIT(NUM) AXIS_INIT(e## NUM, E## NUM, E)
 
-  // Initialize Step Pins
+  // Init Step Pins
   #if HAS_X_STEP
     #if ENABLED(X_DUAL_STEPPER_DRIVERS) || ENABLED(DUAL_X_CARRIAGE)
       X2_STEP_INIT;
@@ -1164,28 +1166,28 @@ void Stepper::report_positions() {
 
 #endif //HAS_DIGIPOTSS
 
+#if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM
+
   void Stepper::digipot_init() {
     #if HAS_DIGIPOTSS
-    const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT;
+      static const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT;
-
       SPI.begin();
-    pinMode(DIGIPOTSS_PIN, OUTPUT);
+      SET_OUTPUT(DIGIPOTSS_PIN);
       for (uint8_t i = 0; i < COUNT(digipot_motor_current); i++) {
         //digitalPotWrite(digipot_ch[i], digipot_motor_current[i]);
         digipot_current(i, digipot_motor_current[i]);
       }
-  #endif
+    #elif HAS_MOTOR_CURRENT_PWM
-  #if HAS_MOTOR_CURRENT_PWM
       #if PIN_EXISTS(MOTOR_CURRENT_PWM_XY)
-      pinMode(MOTOR_CURRENT_PWM_XY_PIN, OUTPUT);
+        SET_OUTPUT(MOTOR_CURRENT_PWM_XY_PIN);
         digipot_current(0, motor_current_setting[0]);
       #endif
       #if PIN_EXISTS(MOTOR_CURRENT_PWM_Z)
-      pinMode(MOTOR_CURRENT_PWM_Z_PIN, OUTPUT);
+        SET_OUTPUT(MOTOR_CURRENT_PWM_Z_PIN);
         digipot_current(1, motor_current_setting[1]);
       #endif
       #if PIN_EXISTS(MOTOR_CURRENT_PWM_E)
-      pinMode(MOTOR_CURRENT_PWM_E_PIN, OUTPUT);
+        SET_OUTPUT(MOTOR_CURRENT_PWM_E_PIN);
         digipot_current(2, motor_current_setting[2]);
       #endif
       //Set timer5 to 31khz so the PWM of the motor power is as constant as possible. (removes a buzzing noise)
@@ -1210,53 +1212,69 @@ void Stepper::digipot_current(uint8_t driver, int current) {
           case 2: _WRITE_CURRENT_PWM(MOTOR_CURRENT_PWM_E_PIN); break;
         #endif
       }
-  #else
-    UNUSED(driver);
-    UNUSED(current);
     #endif
   }
 
-void Stepper::microstep_init() {
-  #if HAS_MICROSTEPS_E1
-    pinMode(E1_MS1_PIN, OUTPUT);
-    pinMode(E1_MS2_PIN, OUTPUT);
 #endif
 
 #if HAS_MICROSTEPS
-    pinMode(X_MS1_PIN, OUTPUT);
-    pinMode(X_MS2_PIN, OUTPUT);
-    pinMode(Y_MS1_PIN, OUTPUT);
-    pinMode(Y_MS2_PIN, OUTPUT);
-    pinMode(Z_MS1_PIN, OUTPUT);
-    pinMode(Z_MS2_PIN, OUTPUT);
-    pinMode(E0_MS1_PIN, OUTPUT);
-    pinMode(E0_MS2_PIN, OUTPUT);
-    const uint8_t microstep_modes[] = MICROSTEP_MODES;
-    for (uint16_t i = 0; i < COUNT(microstep_modes); i++)
-      microstep_mode(i, microstep_modes[i]);
-  #endif
-}
 
   /**
    * Software-controlled Microstepping
    */
 
+  void Stepper::microstep_init() {
+    SET_OUTPUT(X_MS1_PIN);
+    SET_OUTPUT(X_MS2_PIN);
+    #if HAS_MICROSTEPS_Y
+      SET_OUTPUT(Y_MS1_PIN);
+      SET_OUTPUT(Y_MS2_PIN);
+    #endif
+    #if HAS_MICROSTEPS_Z
+      SET_OUTPUT(Z_MS1_PIN);
+      SET_OUTPUT(Z_MS2_PIN);
+    #endif
+    #if HAS_MICROSTEPS_E0
+      SET_OUTPUT(E0_MS1_PIN);
+      SET_OUTPUT(E0_MS2_PIN);
+    #endif
+    #if HAS_MICROSTEPS_E1
+      SET_OUTPUT(E1_MS1_PIN);
+      SET_OUTPUT(E1_MS2_PIN);
+    #endif
+    static const uint8_t microstep_modes[] = MICROSTEP_MODES;
+    for (uint16_t i = 0; i < COUNT(microstep_modes); i++)
+      microstep_mode(i, microstep_modes[i]);
+  }
+
   void Stepper::microstep_ms(uint8_t driver, int8_t ms1, int8_t ms2) {
     if (ms1 >= 0) switch (driver) {
       case 0: digitalWrite(X_MS1_PIN, ms1); break;
+      #if HAS_MICROSTEPS_Y
         case 1: digitalWrite(Y_MS1_PIN, ms1); break;
+      #endif
+      #if HAS_MICROSTEPS_Z
         case 2: digitalWrite(Z_MS1_PIN, ms1); break;
+      #endif
+      #if HAS_MICROSTEPS_E0
         case 3: digitalWrite(E0_MS1_PIN, ms1); break;
+      #endif
       #if HAS_MICROSTEPS_E1
         case 4: digitalWrite(E1_MS1_PIN, ms1); break;
       #endif
     }
     if (ms2 >= 0) switch (driver) {
       case 0: digitalWrite(X_MS2_PIN, ms2); break;
+      #if HAS_MICROSTEPS_Y
         case 1: digitalWrite(Y_MS2_PIN, ms2); break;
+      #endif
+      #if HAS_MICROSTEPS_Z
         case 2: digitalWrite(Z_MS2_PIN, ms2); break;
+      #endif
+      #if HAS_MICROSTEPS_E0
         case 3: digitalWrite(E0_MS2_PIN, ms2); break;
-    #if PIN_EXISTS(E1_MS2)
+      #endif
+      #if HAS_MICROSTEPS_E1
         case 4: digitalWrite(E1_MS2_PIN, ms2); break;
       #endif
     }
@@ -1277,15 +1295,21 @@ void Stepper::microstep_readings() {
     SERIAL_PROTOCOLPGM("X: ");
     SERIAL_PROTOCOL(READ(X_MS1_PIN));
     SERIAL_PROTOCOLLN(READ(X_MS2_PIN));
+    #if HAS_MICROSTEPS_Y
       SERIAL_PROTOCOLPGM("Y: ");
       SERIAL_PROTOCOL(READ(Y_MS1_PIN));
       SERIAL_PROTOCOLLN(READ(Y_MS2_PIN));
+    #endif
+    #if HAS_MICROSTEPS_Z
       SERIAL_PROTOCOLPGM("Z: ");
       SERIAL_PROTOCOL(READ(Z_MS1_PIN));
       SERIAL_PROTOCOLLN(READ(Z_MS2_PIN));
+    #endif
+    #if HAS_MICROSTEPS_E0
       SERIAL_PROTOCOLPGM("E0: ");
       SERIAL_PROTOCOL(READ(E0_MS1_PIN));
       SERIAL_PROTOCOLLN(READ(E0_MS2_PIN));
+    #endif
     #if HAS_MICROSTEPS_E1
       SERIAL_PROTOCOLPGM("E1: ");
       SERIAL_PROTOCOL(READ(E1_MS1_PIN));
@@ -1293,6 +1317,8 @@ void Stepper::microstep_readings() {
     #endif
   }
 
+#endif // HAS_MICROSTEPS
+
 #if ENABLED(LIN_ADVANCE)
 
   void Stepper::advance_M905(const float &k) {

Marlin/stepper.h

@@ -239,13 +239,16 @@ class Stepper {
     //
     static FORCE_INLINE bool motor_direction(AxisEnum axis) { return TEST(last_direction_bits, axis); }
 
-    #if HAS_DIGIPOTSS
+    #if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM
       static void digitalPotWrite(int address, int value);
-    #endif
-    static void microstep_ms(uint8_t driver, int8_t ms1, int8_t ms2);
       static void digipot_current(uint8_t driver, int current);
+    #endif
+
+    #if HAS_MICROSTEPS
+      static void microstep_ms(uint8_t driver, int8_t ms1, int8_t ms2);
       static void microstep_mode(uint8_t driver, uint8_t stepping);
       static void microstep_readings();
+    #endif
 
     #if ENABLED(Z_DUAL_ENDSTOPS)
       static FORCE_INLINE void set_homing_flag(bool state) { performing_homing = state; }
@@ -380,7 +383,10 @@ class Stepper {
     }
 
     static void digipot_init();
+
+    #if HAS_MICROSTEPS
       static void microstep_init();
+    #endif
 
 };