From 6165fd41a58e814f6966874c1de84a938ba0c787 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sun, 6 Mar 2016 01:37:43 -0800 Subject: [PATCH] Fix Hephestos 2 and other configs --- .../Hephestos/Configuration.h | 3 + .../Hephestos/Configuration_adv.h | 4 +- .../Hephestos_2/Configuration.h | 52 ++++++----- .../Hephestos_2/Configuration_adv.h | 90 ++++++++++--------- .../WITBOX/Configuration_adv.h | 4 +- .../delta/biv2.5/Configuration_adv.h | 4 +- .../delta/kossel_xl/Configuration.h | 5 -- 7 files changed, 80 insertions(+), 82 deletions(-) diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 8caf0f610..c61f3fd08 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -731,6 +731,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // http://reprap.org/wiki/Mini_panel //#define MINIPANEL +// BQ SMART FULL GRAPHIC CONTROLLER +//#define BQ_LCD_SMART_CONTROLLER + /** * I2C Panels */ diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 9e34fb5d3..26967e195 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -443,11 +443,11 @@ const unsigned int dropsegments = 5; //everything with less than this number of #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt #define RETRACT_LENGTH 3 //default retract length (positive mm) #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change - #define RETRACT_FEEDRATE 80*60 //default feedrate for retracting (mm/s) + #define RETRACT_FEEDRATE 80 //default feedrate for retracting (mm/s) #define RETRACT_ZLIFT 0 //default retract Z-lift #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering) //#define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change) - #define RETRACT_RECOVER_FEEDRATE 8*60 //default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif // Add support for experimental filament exchange support M600; requires display diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index bf5a84a57..c7e1b02ae 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -179,11 +179,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R @@ -248,13 +243,13 @@ Here are some standard links for getting your machine calibrated: #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) #define DEFAULT_bedKp 10.00 #define DEFAULT_bedKi .023 #define DEFAULT_bedKd 305.4 - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune //#define DEFAULT_bedKp 97.1 //#define DEFAULT_bedKi 1.41 @@ -349,11 +344,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_ENABLE_ON 0 #define E_ENABLE_ON 0 // For all extruders -// Disables axis when it's not being used. +// Disables axis stepper immediately when it's not being used. // WARNING: When motors turn off there is a chance of losing position accuracy! #define DISABLE_X false #define DISABLE_Y false #define DISABLE_Z false +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING // @section extruder @@ -411,16 +408,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif //=========================================================================== -//=========================== Manual Bed Leveling =========================== +//============================ Mesh Bed Leveling ============================ //=========================================================================== -//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MESH_BED_LEVELING // Enable mesh bed leveling. -#if ENABLED(MANUAL_BED_LEVELING) - #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis. -#endif // MANUAL_BED_LEVELING - #if ENABLED(MESH_BED_LEVELING) #define MESH_MIN_X 10 #define MESH_MAX_X (X_MAX_POS - MESH_MIN_X) @@ -429,6 +421,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_Y_POINTS 3 #define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. + + //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. + + #if ENABLED(MANUAL_BED_LEVELING) + #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis. + #endif // MANUAL_BED_LEVELING + #endif // MESH_BED_LEVELING //=========================================================================== @@ -437,6 +436,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // @section bedlevel + #define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define DEBUG_LEVELING_FEATURE #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. @@ -451,7 +451,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // This mode is preferred because there are more measurements. // // - "3-point" mode - // Probe 3 arbitrary points on the bed (that aren't colinear) + // Probe 3 arbitrary points on the bed (that aren't collinear) // You specify the XY coordinates of all 3 points. // Enable this to sample the bed in a grid (least squares solution). @@ -493,7 +493,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define Z_RAISE_BEFORE_HOMING 5 // (in mm) Raise Z axis before homing (G28) for Z probe clearance. // Be sure you have this distance over your Z_MAX_POS in case. - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. + #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BEFORE_PROBING 5 // How much the Z axis will be raised before traveling to the first probing point. #define Z_RAISE_BETWEEN_PROBINGS 1 // How much the Z axis will be raised when traveling from between next probing points. @@ -505,9 +505,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, - //it is highly recommended you let this Z_SAFE_HOMING enabled!!! + // If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, + // it is highly recommended you let this Z_SAFE_HOMING enabled!!! #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area. // When defined, it will: @@ -661,9 +660,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define ULTRA_LCD //general LCD support, also 16x2 //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) #define SDSUPPORT // Enable SD Card Support in Hardware Console -// Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) + // Changed behaviour! If you need SDSUPPORT uncomment it! +//#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking @@ -683,13 +681,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD // http://panucatt.com -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino //#define VIKI2 //#define miniVIKI // This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ // -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino //#define ELB_FULL_GRAPHIC_CONTROLLER //#define SD_DETECT_INVERTED @@ -743,7 +741,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define LCD_I2C_VIKI // SSD1306 OLED generic display support -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino //#define U8GLIB_SSD1306 // Shift register panels @@ -755,7 +753,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // @section extras -// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino //#define FAST_PWM_FAN // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency @@ -843,7 +841,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm -#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) +#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm) - limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) //defines used in the code #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h index cf36580be..c4b9ff4c3 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h @@ -112,7 +112,7 @@ #define EXTRUDER_2_AUTO_FAN_PIN -1 #define EXTRUDER_3_AUTO_FAN_PIN -1 #define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed //=========================================================================== @@ -232,7 +232,13 @@ #define INVERT_E_STEP_PIN false // Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 @@ -341,16 +347,17 @@ #define USE_SMALL_INFOFONT #endif // DOGLCD + // @section more // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation. #define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -361,7 +368,6 @@ //#define BABYSTEPPING #if ENABLED(BABYSTEPPING) #define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions - //not implemented for CoreXY and deltabots! #define BABYSTEP_INVERT_Z false //true for inverse movements in Z #define BABYSTEP_MULTIPLICATOR 1 //faster movements #endif @@ -380,7 +386,6 @@ #if ENABLED(ADVANCE) #define EXTRUDER_ADVANCE_K .0 #define D_FILAMENT 2.85 - #define STEPS_MM_E 836 #endif // @section extras @@ -389,7 +394,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -454,7 +459,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define FILAMENTCHANGE_ZADD 10 #define FILAMENTCHANGE_FIRSTRETRACT -2 #define FILAMENTCHANGE_FINALRETRACT -100 - #define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD + #define AUTO_FILAMENT_CHANGE //This extrudes filament until you press the button on LCD #define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop #define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop #endif @@ -462,7 +467,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st /******************************************************************************\ * enable this section if you have TMC26X motor drivers. - * you need to import the TMC26XStepper library into the arduino IDE for this + * you need to import the TMC26XStepper library into the Arduino IDE for this ******************************************************************************/ // @section tmc @@ -470,52 +475,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -524,7 +529,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st /******************************************************************************\ * enable this section if you have L6470 motor drivers. - * you need to import the L6470 library into the arduino IDE for this + * you need to import the L6470 library into the Arduino IDE for this ******************************************************************************/ // @section l6470 @@ -532,66 +537,63 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps - #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps - #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps - #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index f0c819c08..26967e195 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -443,11 +443,11 @@ const unsigned int dropsegments = 5; //everything with less than this number of #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt #define RETRACT_LENGTH 3 //default retract length (positive mm) #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change - #define RETRACT_FEEDRATE 80*60 //default feedrate for retracting (mm/s) + #define RETRACT_FEEDRATE 80 //default feedrate for retracting (mm/s) #define RETRACT_ZLIFT 0 //default retract Z-lift #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering) //#define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change) - #define RETRACT_RECOVER_FEEDRATE 8*60 //default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif // Add support for experimental filament exchange support M600; requires display diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h index 9ab22d522..0c540e252 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h @@ -444,11 +444,11 @@ const unsigned int dropsegments = 5; //everything with less than this number of #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt #define RETRACT_LENGTH 5 //default retract length (positive mm) #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change - #define RETRACT_FEEDRATE 100 //default feedrate for retracting (mm/s) + #define RETRACT_FEEDRATE 100 //default feedrate for retracting (mm/s) #define RETRACT_ZLIFT 0 //default retract Z-lift #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering) #define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change) - #define RETRACT_RECOVER_FEEDRATE 100 //default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE 100 //default feedrate for recovering from retraction (mm/s) #endif // Add support for experimental filament exchange support M600; requires display diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index 4a536b76f..521411865 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -201,11 +201,6 @@ Here are some standard links for getting your machine calibrated: #define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R