CMS/Marlin
3
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

M141 Heated Chamber, Temperature rework (#12201)

Browse Source
This commit is contained in:
3dlabsio 2019-03-07 00:09:39 -08:00 committed by Scott Lahteine
parent 44571775bd
commit 645ca7af7a
196 changed files with 2183 additions and 676 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

2
Marlin/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
Marlin/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
Marlin/src/core/language.h
View File

@ -285,6 +285,8 @@
#define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !" #define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !"
#define MSG_HEATER_BED "bed" #define MSG_HEATER_BED "bed"
#define MSG_HEATER_CHAMBER "chamber"
#define MSG_STOPPED_HEATER ", system stopped! Heater_ID: " #define MSG_STOPPED_HEATER ", system stopped! Heater_ID: "
#define MSG_REDUNDANCY "Heater switched off. Temperature difference between temp sensors is too high !" #define MSG_REDUNDANCY "Heater switched off. Temperature difference between temp sensors is too high !"
#define MSG_T_HEATING_FAILED "Heating failed" #define MSG_T_HEATING_FAILED "Heating failed"

2
Marlin/src/feature/controllerfan.cpp
View File

@ -39,7 +39,7 @@ void controllerfan_update() {
// If any of the drivers or the bed are enabled... // If any of the drivers or the bed are enabled...
if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON
#if HAS_HEATED_BED #if HAS_HEATED_BED
|| thermalManager.soft_pwm_amount_bed > 0 || thermalManager.temp_bed.soft_pwm_amount > 0
#endif #endif
#if HAS_X2_ENABLE #if HAS_X2_ENABLE
|| X2_ENABLE_READ == X_ENABLE_ON || X2_ENABLE_READ == X_ENABLE_ON

10
Marlin/src/feature/pause.cpp
View File

@ -482,8 +482,7 @@ void wait_for_confirmation(const bool is_reload/*=false*/, const int8_t max_beep
// Start the heater idle timers // Start the heater idle timers
const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL; const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL;
HOTEND_LOOP() HOTEND_LOOP() thermalManager.hotend_idle[e].start(nozzle_timeout);
thermalManager.start_heater_idle_timer(e, nozzle_timeout);
#if ENABLED(DUAL_X_CARRIAGE) #if ENABLED(DUAL_X_CARRIAGE)
const int8_t saved_ext = active_extruder; const int8_t saved_ext = active_extruder;
@ -505,7 +504,7 @@ void wait_for_confirmation(const bool is_reload/*=false*/, const int8_t max_beep
// If the nozzle has timed out... // If the nozzle has timed out...
if (!nozzle_timed_out) if (!nozzle_timed_out)
HOTEND_LOOP() nozzle_timed_out |= thermalManager.is_heater_idle(e); HOTEND_LOOP() nozzle_timed_out |= thermalManager.hotend_idle[e].timed_out;
// Wait for the user to press the button to re-heat the nozzle, then // Wait for the user to press the button to re-heat the nozzle, then
// re-heat the nozzle, re-show the continue prompt, restart idle timers, start over // re-heat the nozzle, re-show the continue prompt, restart idle timers, start over
@ -538,8 +537,7 @@ void wait_for_confirmation(const bool is_reload/*=false*/, const int8_t max_beep
// Start the heater idle timers // Start the heater idle timers
const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL; const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL;
HOTEND_LOOP() HOTEND_LOOP() thermalManager.hotend_idle[e].start(nozzle_timeout);
thermalManager.start_heater_idle_timer(e, nozzle_timeout);
#if ENABLED(HOST_PROMPT_SUPPORT) #if ENABLED(HOST_PROMPT_SUPPORT)
host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Reheat Done"), PSTR("Continue")); host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Reheat Done"), PSTR("Continue"));
#endif #endif
@ -594,7 +592,7 @@ void resume_print(const float &slow_load_length/*=0*/, const float &fast_load_le
// Re-enable the heaters if they timed out // Re-enable the heaters if they timed out
bool nozzle_timed_out = false; bool nozzle_timed_out = false;
HOTEND_LOOP() { HOTEND_LOOP() {
nozzle_timed_out |= thermalManager.is_heater_idle(e); nozzle_timed_out |= thermalManager.hotend_idle[e].timed_out;
thermalManager.reset_heater_idle_timer(e); thermalManager.reset_heater_idle_timer(e);
} }

2
Marlin/src/feature/power.cpp
View File

@ -53,7 +53,7 @@ bool Power::is_power_needed() {
// If any of the drivers or the bed are enabled... // If any of the drivers or the bed are enabled...
if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON
#if HAS_HEATED_BED #if HAS_HEATED_BED
|| thermalManager.soft_pwm_amount_bed > 0 || thermalManager.temp_bed.soft_pwm_amount > 0
#endif #endif
#if HAS_X2_ENABLE #if HAS_X2_ENABLE
|| X2_ENABLE_READ == X_ENABLE_ON || X2_ENABLE_READ == X_ENABLE_ON

6
Marlin/src/feature/power_loss_recovery.cpp
View File

@ -155,10 +155,10 @@ void PrintJobRecovery::save(const bool force/*=false*/, const bool save_queue/*=
info.active_hotend = active_extruder; info.active_hotend = active_extruder;
#endif #endif
COPY(info.target_temperature, thermalManager.target_temperature); HOTEND_LOOP() info.target_temperature[e] = thermalManager.temp_hotend[e].target;
#if HAS_HEATED_BED #if HAS_HEATED_BED
info.target_temperature_bed = thermalManager.target_temperature_bed; info.target_temperature_bed = thermalManager.temp_bed.target;
#endif #endif
#if FAN_COUNT #if FAN_COUNT
@ -385,7 +385,7 @@ void PrintJobRecovery::resume() {
#if FAN_COUNT #if FAN_COUNT
SERIAL_ECHOPGM("fan_speed: "); SERIAL_ECHOPGM("fan_speed: ");
for (int8_t i = 0; i < FAN_COUNT; i++) { FANS_LOOP(i) {
SERIAL_ECHO(int(info.fan_speed[i])); SERIAL_ECHO(int(info.fan_speed[i]));
if (i < FAN_COUNT - 1) SERIAL_CHAR(','); if (i < FAN_COUNT - 1) SERIAL_CHAR(',');
} }

12
Marlin/src/gcode/config/M304.cpp
View File

@ -28,14 +28,14 @@
#include "../../module/temperature.h" #include "../../module/temperature.h"
void GcodeSuite::M304() { void GcodeSuite::M304() {
if (parser.seen('P')) thermalManager.bed_pid.Kp = parser.value_float(); if (parser.seen('P')) thermalManager.temp_bed.pid.Kp = parser.value_float();
if (parser.seen('I')) thermalManager.bed_pid.Ki = scalePID_i(parser.value_float()); if (parser.seen('I')) thermalManager.temp_bed.pid.Ki = scalePID_i(parser.value_float());
if (parser.seen('D')) thermalManager.bed_pid.Kd = scalePID_d(parser.value_float()); if (parser.seen('D')) thermalManager.temp_bed.pid.Kd = scalePID_d(parser.value_float());
SERIAL_ECHO_START(); SERIAL_ECHO_START();
SERIAL_ECHOPAIR(" p:", thermalManager.bed_pid.Kp); SERIAL_ECHOPAIR(" p:", thermalManager.temp_bed.pid.Kp);
SERIAL_ECHOPAIR(" i:", unscalePID_i(thermalManager.bed_pid.Ki)); SERIAL_ECHOPAIR(" i:", unscalePID_i(thermalManager.temp_bed.pid.Ki));
SERIAL_ECHOLNPAIR(" d:", unscalePID_d(thermalManager.bed_pid.Kd)); SERIAL_ECHOLNPAIR(" d:", unscalePID_d(thermalManager.temp_bed.pid.Kd));
} }
#endif // PIDTEMPBED #endif // PIDTEMPBED

5
Marlin/src/gcode/gcode.cpp
View File

@ -392,6 +392,11 @@ void GcodeSuite::process_parsed_command(
case 190: M190(); break; // M190: Wait for bed temperature to reach target case 190: M190(); break; // M190: Wait for bed temperature to reach target
#endif #endif
#if HAS_HEATED_CHAMBER
case 141: M141(); break; // M141: Set chamber temperature
//case 191: M191(); break; // M191: Wait for chamber temperature to reach target
#endif
case 105: M105(); KEEPALIVE_STATE(NOT_BUSY); return; // M105: Report Temperatures (and say "ok") case 105: M105(); KEEPALIVE_STATE(NOT_BUSY); return; // M105: Report Temperatures (and say "ok")
#if ENABLED(AUTO_REPORT_TEMPERATURES) && HAS_TEMP_SENSOR #if ENABLED(AUTO_REPORT_TEMPERATURES) && HAS_TEMP_SENSOR

5
Marlin/src/gcode/gcode.h
View File

@ -576,6 +576,11 @@ private:
static void M190(); static void M190();
#endif #endif
#if HAS_HEATED_CHAMBER
static void M141();
//static void M191();
#endif
#if HAS_LCD_MENU #if HAS_LCD_MENU
static void M145(); static void M145();
#endif #endif

77
Marlin/src/gcode/temperature/M141_M191.cpp Normal file
View File

@ -0,0 +1,77 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#include "../../inc/MarlinConfig.h"
#if HAS_HEATED_CHAMBER
#include "../gcode.h"
#include "../../module/temperature.h"
/*
#include "../../module/motion.h"
#include "../../lcd/ultralcd.h"
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
#include "../../module/printcounter.h"
#endif
#if ENABLED(PRINTER_EVENT_LEDS)
#include "../../feature/leds/leds.h"
#endif
#include "../../Marlin.h" // for wait_for_heatup and idle()
*/
/**
* M141: Set chamber temperature
*/
void GcodeSuite::M141() {
if (DEBUGGING(DRYRUN)) return;
if (parser.seenval('S')) thermalManager.setTargetChamber(parser.value_celsius());
}
/**
* M191: Sxxx Wait for chamber current temp to reach target temp. Waits only when heating
* Rxxx Wait for chamber current temp to reach target temp. Waits when heating and cooling
*/
/*
void GcodeSuite::M191() {
if (DEBUGGING(DRYRUN)) return;
const bool no_wait_for_cooling = parser.seenval('S');
if (no_wait_for_cooling || parser.seenval('R')) {
thermalManager.setTargetBed(parser.value_celsius());
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
if (parser.value_celsius() > BED_MINTEMP)
print_job_timer.start();
#endif
}
else return;
lcd_setstatusPGM(thermalManager.isHeatingBed() ? PSTR(MSG_BED_HEATING) : PSTR(MSG_BED_COOLING));
thermalManager.wait_for_bed(no_wait_for_cooling);
}
*/
#endif // HAS_HEATED_CHAMBER

17
Marlin/src/inc/Conditionals_post.h
View File

@ -921,6 +921,7 @@
#define HAS_TEMP_HOTEND (HAS_TEMP_ADC_0 || ENABLED(HEATER_0_USES_MAX6675)) #define HAS_TEMP_HOTEND (HAS_TEMP_ADC_0 || ENABLED(HEATER_0_USES_MAX6675))
#define HAS_TEMP_BED HAS_TEMP_ADC_BED #define HAS_TEMP_BED HAS_TEMP_ADC_BED
#define HAS_TEMP_CHAMBER HAS_TEMP_ADC_CHAMBER #define HAS_TEMP_CHAMBER HAS_TEMP_ADC_CHAMBER
#define HAS_HEATED_CHAMBER (HAS_TEMP_CHAMBER && PIN_EXISTS(CHAMBER_HEATER))
// Heaters // Heaters
#define HAS_HEATER_0 (PIN_EXISTS(HEATER_0)) #define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))
@ -945,7 +946,8 @@
// Thermal protection // Thermal protection
#define HAS_THERMALLY_PROTECTED_BED (HAS_HEATED_BED && ENABLED(THERMAL_PROTECTION_BED)) #define HAS_THERMALLY_PROTECTED_BED (HAS_HEATED_BED && ENABLED(THERMAL_PROTECTION_BED))
#define WATCH_HOTENDS (ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0) #define WATCH_HOTENDS (ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0)
#define WATCH_THE_BED (HAS_THERMALLY_PROTECTED_BED && WATCH_BED_TEMP_PERIOD > 0) #define WATCH_BED (HAS_THERMALLY_PROTECTED_BED && WATCH_BED_TEMP_PERIOD > 0)
#define WATCH_CHAMBER (HAS_HEATED_CHAMBER && ENABLED(THERMAL_PROTECTION_CHAMBER) && WATCH_CHAMBER_TEMP_PERIOD > 0)
// Auto fans // Auto fans
#define HAS_AUTO_FAN_0 (PIN_EXISTS(E0_AUTO_FAN)) #define HAS_AUTO_FAN_0 (PIN_EXISTS(E0_AUTO_FAN))
@ -1151,6 +1153,19 @@
#define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, (v) ^ HEATER_BED_INVERTING) #define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, (v) ^ HEATER_BED_INVERTING)
#endif #endif
/**
* Heated chamber requires settings
*/
#if HAS_HEATED_CHAMBER
#ifndef MAX_CHAMBER_POWER
#define MAX_CHAMBER_POWER 255
#endif
#ifndef HEATER_CHAMBER_INVERTING
#define HEATER_CHAMBER_INVERTING false
#endif
#define WRITE_HEATER_CHAMBER(v) WRITE(HEATER_CHAMBER_PIN, (v) ^ HEATER_CHAMBER_INVERTING)
#endif
/** /**
* Up to 3 PWM fans * Up to 3 PWM fans
*/ */

4
Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp
View File

@ -544,9 +544,9 @@ FORCE_INLINE void _draw_heater_status(const int8_t heater, const char prefix, co
#else #else
const bool is_idle = ( const bool is_idle = (
#if HAS_HEATED_BED #if HAS_HEATED_BED
isBed ? thermalManager.is_bed_idle() : isBed ? thermalManager.bed_idle.timed_out :
#endif #endif
thermalManager.is_heater_idle(heater) thermalManager.hotend_idle[heater].timed_out
); );
if (!blink && is_idle) { if (!blink && is_idle) {

2
Marlin/src/lcd/dogm/status_screen_DOGM.cpp
View File

@ -208,7 +208,7 @@ FORCE_INLINE void _draw_heater_status(const int8_t heater, const bool blink) {
if (PAGE_UNDER(7)) { if (PAGE_UNDER(7)) {
#if HEATER_IDLE_HANDLER #if HEATER_IDLE_HANDLER
const bool is_idle = IFBED(thermalManager.is_bed_idle(), thermalManager.is_heater_idle(heater)), const bool is_idle = IFBED(thermalManager.bed_idle.timed_out, thermalManager.hotend_idle[heater].timed_out),
dodraw = (blink || !is_idle); dodraw = (blink || !is_idle);
#else #else
constexpr bool dodraw = true; constexpr bool dodraw = true;

2
Marlin/src/lcd/dogm/ultralcd_DOGM.cpp
View File

@ -261,7 +261,7 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop
lcd_put_u8str(i16tostr3(thermalManager.degHotend(extruder))); lcd_put_u8str(i16tostr3(thermalManager.degHotend(extruder)));
lcd_put_wchar('/'); lcd_put_wchar('/');
if (get_blink() || !thermalManager.is_heater_idle(extruder)) if (get_blink() || !thermalManager.hotend_idle[extruder].timed_out)
lcd_put_u8str(i16tostr3(thermalManager.degTargetHotend(extruder))); lcd_put_u8str(i16tostr3(thermalManager.degTargetHotend(extruder)));
} }

9
Marlin/src/lcd/language/language_en.h
View File

@ -537,6 +537,9 @@
#ifndef MSG_BED #ifndef MSG_BED
#define MSG_BED _UxGT("Bed") #define MSG_BED _UxGT("Bed")
#endif #endif
#ifndef MSG_CHAMBER
#define MSG_CHAMBER _UxGT("Enclosure")
#endif
#ifndef MSG_FAN_SPEED #ifndef MSG_FAN_SPEED
#define MSG_FAN_SPEED _UxGT("Fan speed") #define MSG_FAN_SPEED _UxGT("Fan speed")
#endif #endif
@ -921,6 +924,12 @@
#ifndef MSG_ERR_MINTEMP_BED #ifndef MSG_ERR_MINTEMP_BED
#define MSG_ERR_MINTEMP_BED _UxGT("Err: MINTEMP BED") #define MSG_ERR_MINTEMP_BED _UxGT("Err: MINTEMP BED")
#endif #endif
#ifndef MSG_ERR_MAXTEMP_CHAMBER
#define MSG_ERR_MAXTEMP_CHAMBER _UxGT("Err: MAXTEMP CHAMBER")
#endif
#ifndef MSG_ERR_MINTEMP_CHAMBER
#define MSG_ERR_MINTEMP_CHAMBER _UxGT("Err: MINTEMP CHAMBER")
#endif
#ifndef MSG_ERR_Z_HOMING #ifndef MSG_ERR_Z_HOMING
#define MSG_ERR_Z_HOMING MSG_HOME _UxGT(" ") MSG_X MSG_Y _UxGT(" ") MSG_FIRST #define MSG_ERR_Z_HOMING MSG_HOME _UxGT(" ") MSG_X MSG_Y _UxGT(" ") MSG_FIRST
#endif #endif

35
Marlin/src/lcd/menu/menu.cpp
View File

@ -37,7 +37,7 @@
#include "../../module/configuration_store.h" #include "../../module/configuration_store.h"
#endif #endif
#if WATCH_HOTENDS || WATCH_THE_BED || ENABLED(BABYSTEP_ZPROBE_OFFSET) #if WATCH_HOTENDS || WATCH_BED || ENABLED(BABYSTEP_ZPROBE_OFFSET)
#include "../../module/temperature.h" #include "../../module/temperature.h"
#endif #endif
@ -405,39 +405,6 @@ void MarlinUI::completion_feedback(const bool good/*=true*/) {
#endif // BABYSTEP_ZPROBE_OFFSET #endif // BABYSTEP_ZPROBE_OFFSET
/**
* Watch temperature callbacks
*/
#if HAS_TEMP_HOTEND
#if WATCH_HOTENDS
#define _WATCH_FUNC(N) thermalManager.start_watching_heater(N)
#else
#define _WATCH_FUNC(N) NOOP
#endif
void watch_temp_callback_E0() { _WATCH_FUNC(0); }
#if HOTENDS > 1
void watch_temp_callback_E1() { _WATCH_FUNC(1); }
#if HOTENDS > 2
void watch_temp_callback_E2() { _WATCH_FUNC(2); }
#if HOTENDS > 3
void watch_temp_callback_E3() { _WATCH_FUNC(3); }
#if HOTENDS > 4
void watch_temp_callback_E4() { _WATCH_FUNC(4); }
#if HOTENDS > 5
void watch_temp_callback_E5() { _WATCH_FUNC(5); }
#endif // HOTENDS > 5
#endif // HOTENDS > 4
#endif // HOTENDS > 3
#endif // HOTENDS > 2
#endif // HOTENDS > 1
#endif // HAS_TEMP_HOTEND
void watch_temp_callback_bed() {
#if WATCH_THE_BED
thermalManager.start_watching_bed();
#endif
}
#if ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(PID_AUTOTUNE_MENU) || ENABLED(ADVANCED_PAUSE_FEATURE) #if ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(PID_AUTOTUNE_MENU) || ENABLED(ADVANCED_PAUSE_FEATURE)
void lcd_enqueue_command(const char * const cmd) { void lcd_enqueue_command(const char * const cmd) {

8
Marlin/src/lcd/menu/menu.h
View File

@ -340,14 +340,6 @@ void menu_move();
void lcd_move_z(); void lcd_move_z();
void _lcd_draw_homing(); void _lcd_draw_homing();
void watch_temp_callback_E0();
void watch_temp_callback_E1();
void watch_temp_callback_E2();
void watch_temp_callback_E3();
void watch_temp_callback_E4();
void watch_temp_callback_E5();
void watch_temp_callback_bed();
#define HAS_LINE_TO_Z (ENABLED(DELTA) || ENABLED(PROBE_MANUALLY) || ENABLED(MESH_BED_LEVELING) || ENABLED(LEVEL_BED_CORNERS)) #define HAS_LINE_TO_Z (ENABLED(DELTA) || ENABLED(PROBE_MANUALLY) || ENABLED(MESH_BED_LEVELING) || ENABLED(LEVEL_BED_CORNERS))
#if HAS_LINE_TO_Z #if HAS_LINE_TO_Z

4
Marlin/src/lcd/menu/menu_filament.cpp
View File

@ -61,7 +61,7 @@ static void _change_filament_temp(const uint16_t temperature) {
} }
inline void _lcd_change_filament_temp_1_func() { _change_filament_temp(ui.preheat_hotend_temp[0]); } inline void _lcd_change_filament_temp_1_func() { _change_filament_temp(ui.preheat_hotend_temp[0]); }
inline void _lcd_change_filament_temp_2_func() { _change_filament_temp(ui.preheat_hotend_temp[1]); } inline void _lcd_change_filament_temp_2_func() { _change_filament_temp(ui.preheat_hotend_temp[1]); }
inline void _lcd_change_filament_temp_custom_cb() { _change_filament_temp(thermalManager.target_temperature[_change_filament_temp_extruder]); } inline void _lcd_change_filament_temp_custom_cb() { _change_filament_temp(thermalManager.temp_hotend[_change_filament_temp_extruder].target); }
static PGM_P change_filament_header(const AdvancedPauseMode mode) { static PGM_P change_filament_header(const AdvancedPauseMode mode) {
switch (mode) { switch (mode) {
@ -101,7 +101,7 @@ void _menu_temp_filament_op(const AdvancedPauseMode mode, const int8_t extruder)
#endif #endif
#endif #endif
} }
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_PREHEAT_CUSTOM, &thermalManager.target_temperature[_change_filament_temp_extruder], EXTRUDE_MINTEMP, max_temp - 15, _lcd_change_filament_temp_custom_cb); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_PREHEAT_CUSTOM, &thermalManager.temp_hotend[_change_filament_temp_extruder].target, EXTRUDE_MINTEMP, max_temp - 15, _lcd_change_filament_temp_custom_cb);
END_MENU(); END_MENU();
} }
#if E_STEPPERS #if E_STEPPERS

17
Marlin/src/lcd/menu/menu_temperature.cpp
View File

@ -353,9 +353,9 @@ void menu_temperature() {
// Nozzle [1-5]: // Nozzle [1-5]:
// //
#if HOTENDS == 1 #if HOTENDS == 1
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.temp_hotend[0].target, 0, HEATER_0_MAXTEMP - 15, thermalManager.start_watching_E0);
#else // HOTENDS > 1 #else // HOTENDS > 1
#define EDIT_TARGET(N) MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_LCD_N##N, &thermalManager.target_temperature[N], 0, HEATER_##N##_MAXTEMP - 15, watch_temp_callback_E##N) #define EDIT_TARGET(N) MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_LCD_N##N, &thermalManager.temp_hotend[N].target, 0, HEATER_##N##_MAXTEMP - 15, thermalManager.start_watching_E##N)
EDIT_TARGET(0); EDIT_TARGET(0);
EDIT_TARGET(1); EDIT_TARGET(1);
#if HOTENDS > 2 #if HOTENDS > 2
@ -380,7 +380,14 @@ void menu_temperature() {
// Bed: // Bed:
// //
#if HAS_HEATED_BED #if HAS_HEATED_BED
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.target_temperature_bed, 0, BED_MAXTEMP - 15, watch_temp_callback_bed); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.temp_bed.target, 0, BED_MAXTEMP - 5, thermalManager.start_watching_bed);
#endif
//
// Chamber:
//
#if HAS_HEATED_CHAMBER
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_CHAMBER, &thermalManager.temp_chamber.target, 0, CHAMBER_MAXTEMP - 5, thermalManager.start_watching_chamber);
#endif #endif
// //
@ -413,9 +420,9 @@ void menu_temperature() {
// Cooldown // Cooldown
// //
bool has_heat = false; bool has_heat = false;
HOTEND_LOOP() if (thermalManager.target_temperature[HOTEND_INDEX]) { has_heat = true; break; } HOTEND_LOOP() if (thermalManager.temp_hotend[HOTEND_INDEX].target) { has_heat = true; break; }
#if HAS_TEMP_BED #if HAS_TEMP_BED
if (thermalManager.target_temperature_bed) has_heat = true; if (thermalManager.temp_bed.target) has_heat = true;
#endif #endif
if (has_heat) MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown); if (has_heat) MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown);

6
Marlin/src/lcd/menu/menu_tune.cpp
View File

@ -116,9 +116,9 @@ void menu_tune() {
// Nozzle [1-4]: // Nozzle [1-4]:
// //
#if HOTENDS == 1 #if HOTENDS == 1
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.temp_hotend[0].target, 0, HEATER_0_MAXTEMP - 15, thermalManager.start_watching_E0);
#else // HOTENDS > 1 #else // HOTENDS > 1
#define EDIT_NOZZLE(N) MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_LCD_N##N, &thermalManager.target_temperature[N], 0, HEATER_##N##_MAXTEMP - 15, watch_temp_callback_E##N) #define EDIT_NOZZLE(N) MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_LCD_N##N, &thermalManager.temp_hotend[N].target, 0, HEATER_##N##_MAXTEMP - 15, thermalManager.start_watching_E##N)
EDIT_NOZZLE(0); EDIT_NOZZLE(0);
EDIT_NOZZLE(1); EDIT_NOZZLE(1);
#if HOTENDS > 2 #if HOTENDS > 2
@ -143,7 +143,7 @@ void menu_tune() {
// Bed: // Bed:
// //
#if HAS_HEATED_BED #if HAS_HEATED_BED
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.target_temperature_bed, 0, BED_MAXTEMP - 15, watch_temp_callback_bed); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.temp_bed.target, 0, BED_MAXTEMP - 15, thermalManager.start_watching_bed);
#endif #endif
// //

16
Marlin/src/module/configuration_store.cpp
View File

@ -728,7 +728,7 @@ void MarlinSettings::postprocess() {
const PID_t bed_pid = { DUMMY_PID_VALUE, DUMMY_PID_VALUE, DUMMY_PID_VALUE }; const PID_t bed_pid = { DUMMY_PID_VALUE, DUMMY_PID_VALUE, DUMMY_PID_VALUE };
EEPROM_WRITE(bed_pid); EEPROM_WRITE(bed_pid);
#else #else
EEPROM_WRITE(thermalManager.bed_pid); EEPROM_WRITE(thermalManager.temp_bed.pid);
#endif #endif
} }
@ -1448,7 +1448,7 @@ void MarlinSettings::postprocess() {
EEPROM_READ(pid); EEPROM_READ(pid);
#if ENABLED(PIDTEMPBED) #if ENABLED(PIDTEMPBED)
if (!validating && pid.Kp != DUMMY_PID_VALUE) if (!validating && pid.Kp != DUMMY_PID_VALUE)
memcpy(&thermalManager.bed_pid, &pid, sizeof(pid)); memcpy(&thermalManager.temp_bed.pid, &pid, sizeof(pid));
#endif #endif
} }
@ -2181,9 +2181,9 @@ void MarlinSettings::reset() {
// //
#if ENABLED(PIDTEMPBED) #if ENABLED(PIDTEMPBED)
thermalManager.bed_pid.Kp = DEFAULT_bedKp; thermalManager.temp_bed.pid.Kp = DEFAULT_bedKp;
thermalManager.bed_pid.Ki = scalePID_i(DEFAULT_bedKi); thermalManager.temp_bed.pid.Ki = scalePID_i(DEFAULT_bedKi);
thermalManager.bed_pid.Kd = scalePID_d(DEFAULT_bedKd); thermalManager.temp_bed.pid.Kd = scalePID_d(DEFAULT_bedKd);
#endif #endif
// //
@ -2726,9 +2726,9 @@ void MarlinSettings::reset() {
#if ENABLED(PIDTEMPBED) #if ENABLED(PIDTEMPBED)
CONFIG_ECHO_START(); CONFIG_ECHO_START();
SERIAL_ECHOLNPAIR( SERIAL_ECHOLNPAIR(
" M304 P", thermalManager.bed_pid.Kp " M304 P", thermalManager.temp_bed.pid.Kp
, " I", unscalePID_i(thermalManager.bed_pid.Ki) , " I", unscalePID_i(thermalManager.temp_bed.pid.Ki)
, " D", unscalePID_d(thermalManager.bed_pid.Kd) , " D", unscalePID_d(thermalManager.temp_bed.pid.Kd)
); );
#endif #endif

947
Marlin/src/module/temperature.cpp
View File

File diff suppressed because it is too large Load Diff

419
Marlin/src/module/temperature.h
View File

@ -36,10 +36,12 @@
#define SOFT_PWM_SCALE 0 #define SOFT_PWM_SCALE 0
#endif #endif
#if HOTENDS == 1 #if HOTENDS <= 1
#define HOTEND_INDEX 0 #define HOTEND_INDEX 0
#define E_UNUSED() UNUSED(e)
#else #else
#define HOTEND_INDEX e #define HOTEND_INDEX e
#define E_UNUSED()
#endif #endif
// PID storage // PID storage
@ -47,6 +49,11 @@ typedef struct { float Kp, Ki, Kd; } PID_t;
typedef struct { float Kp, Ki, Kd, Kc; } PIDC_t; typedef struct { float Kp, Ki, Kd, Kc; } PIDC_t;
#if ENABLED(PID_EXTRUSION_SCALING) #if ENABLED(PID_EXTRUSION_SCALING)
typedef PIDC_t hotend_pid_t; typedef PIDC_t hotend_pid_t;
#if LPQ_MAX_LEN > 255
typedef uint16_t lpq_ptr_t;
#else
typedef uint8_t lpq_ptr_t;
#endif
#else #else
typedef PID_t hotend_pid_t; typedef PID_t hotend_pid_t;
#endif #endif
@ -54,11 +61,11 @@ typedef struct { float Kp, Ki, Kd, Kc; } PIDC_t;
#define DUMMY_PID_VALUE 3000.0f #define DUMMY_PID_VALUE 3000.0f
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
#define _PID_Kp(H) Temperature::pid[H].Kp #define _PID_Kp(H) Temperature::temp_hotend[H].pid.Kp
#define _PID_Ki(H) Temperature::pid[H].Ki #define _PID_Ki(H) Temperature::temp_hotend[H].pid.Ki
#define _PID_Kd(H) Temperature::pid[H].Kd #define _PID_Kd(H) Temperature::temp_hotend[H].pid.Kd
#if ENABLED(PID_EXTRUSION_SCALING) #if ENABLED(PID_EXTRUSION_SCALING)
#define _PID_Kc(H) Temperature::pid[H].Kc #define _PID_Kc(H) Temperature::temp_hotend[H].pid.Kc
#else #else
#define _PID_Kc(H) 1 #define _PID_Kc(H) 1
#endif #endif
@ -80,6 +87,14 @@ enum ADCSensorState : char {
PrepareTemp_0, PrepareTemp_0,
MeasureTemp_0, MeasureTemp_0,
#endif #endif
#if HAS_HEATED_BED
PrepareTemp_BED,
MeasureTemp_BED,
#endif
#if HAS_TEMP_CHAMBER
PrepareTemp_CHAMBER,
MeasureTemp_CHAMBER,
#endif
#if HAS_TEMP_ADC_1 #if HAS_TEMP_ADC_1
PrepareTemp_1, PrepareTemp_1,
MeasureTemp_1, MeasureTemp_1,
@ -96,13 +111,9 @@ enum ADCSensorState : char {
PrepareTemp_4, PrepareTemp_4,
MeasureTemp_4, MeasureTemp_4,
#endif #endif
#if HAS_HEATED_BED #if HAS_TEMP_ADC_5
PrepareTemp_BED, PrepareTemp_5,
MeasureTemp_BED, MeasureTemp_5,
#endif
#if HAS_TEMP_CHAMBER
PrepareTemp_CHAMBER,
MeasureTemp_CHAMBER,
#endif #endif
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
Prepare_FILWIDTH, Prepare_FILWIDTH,
@ -136,16 +147,115 @@ enum ADCSensorState : char {
#define G26_CLICK_CAN_CANCEL (HAS_LCD_MENU && ENABLED(G26_MESH_VALIDATION)) #define G26_CLICK_CAN_CANCEL (HAS_LCD_MENU && ENABLED(G26_MESH_VALIDATION))
enum TempIndex : uint8_t {
#if HOTENDS > 0
TEMP_E0,
#if HOTENDS > 1
TEMP_E1,
#if HOTENDS > 2
TEMP_E2,
#if HOTENDS > 3
TEMP_E3,
#if HOTENDS > 4
TEMP_E4,
#if HOTENDS > 5
TEMP_E5,
#endif
#endif
#endif
#endif
#endif
#endif
#if HAS_HEATED_BED
TEMP_BED,
#endif
#if HAS_HEATED_CHAMBER
TEMP_CHAMBER,
#endif
tempCOUNT
};
// A temperature sensor
typedef struct TempInfo {
uint16_t acc;
int16_t raw;
float current;
} temp_info_t;
// A PWM heater with temperature sensor
typedef struct HeaterInfo : public TempInfo {
int16_t target;
uint8_t soft_pwm_amount;
} heater_info_t;
// A heater with PID stabilization
template<typename T>
struct PIDHeaterInfo : public HeaterInfo {
T pid; // Initialized by settings.load()
};
#if ENABLED(PIDTEMP)
typedef struct PIDHeaterInfo<hotend_pid_t> hotend_info_t;
#else
typedef heater_info_t hotend_info_t;
#endif
#if HAS_HEATED_BED
#if ENABLED(PIDTEMPBED)
typedef struct PIDHeaterInfo<PID_t> bed_info_t;
#else
typedef heater_info_t bed_info_t;
#endif
#endif
#if HAS_TEMP_CHAMBER
#if HAS_HEATED_CHAMBER
#if ENABLED(PIDTEMPCHAMBER)
typedef struct PIDHeaterInfo<PID_t> chamber_info_t;
#else
typedef heater_info_t chamber_info_t;
#endif
#else
typedef temp_info_t chamber_info_t;
#endif
#endif
// Heater idle handling
typedef struct {
millis_t timeout_ms;
bool timed_out;
inline void update(const millis_t &ms) { if (!timed_out && timeout_ms && ELAPSED(ms, timeout_ms)) timed_out = true; }
inline void start(const millis_t &ms) { timeout_ms = millis() + ms; timed_out = false; }
inline void reset() { timeout_ms = 0; timed_out = false; }
inline void expire() { start(0); }
} heater_idle_t;
// Heater watch handling
typedef struct {
uint16_t target;
millis_t next_ms;
inline bool elapsed(const millis_t &ms) { return next_ms && ELAPSED(ms, next_ms); }
inline bool elapsed() { return elapsed(millis()); }
} heater_watch_t;
// Temperature sensor read value ranges
typedef struct { int16_t raw_min, raw_max; } raw_range_t;
typedef struct { int16_t mintemp, maxtemp; } celsius_range_t;
typedef struct { int16_t raw_min, raw_max, mintemp, maxtemp; } temp_range_t;
class Temperature { class Temperature {
public: public:
static volatile bool in_temp_isr; static volatile bool in_temp_isr;
static float current_temperature[HOTENDS]; static hotend_info_t temp_hotend[HOTENDS];
static int16_t current_temperature_raw[HOTENDS],
target_temperature[HOTENDS]; #if HAS_HEATED_BED
static uint8_t soft_pwm_amount[HOTENDS]; static bed_info_t temp_bed;
#endif
#if HAS_TEMP_CHAMBER
static chamber_info_t temp_chamber;
#endif
#if ENABLED(AUTO_POWER_E_FANS) #if ENABLED(AUTO_POWER_E_FANS)
static uint8_t autofan_speed[HOTENDS]; static uint8_t autofan_speed[HOTENDS];
@ -156,19 +266,6 @@ class Temperature {
soft_pwm_count_fan[FAN_COUNT]; soft_pwm_count_fan[FAN_COUNT];
#endif #endif
#if ENABLED(PIDTEMP)
static hotend_pid_t pid[HOTENDS];
#endif
#if HAS_HEATED_BED
static float current_temperature_bed;
static int16_t current_temperature_bed_raw, target_temperature_bed;
static uint8_t soft_pwm_amount_bed;
#if ENABLED(PIDTEMPBED)
static PID_t bed_pid;
#endif
#endif
#if ENABLED(BABYSTEPPING) #if ENABLED(BABYSTEPPING)
static volatile int16_t babystepsTodo[3]; static volatile int16_t babystepsTodo[3];
#endif #endif
@ -178,15 +275,11 @@ class Temperature {
static int16_t extrude_min_temp; static int16_t extrude_min_temp;
FORCE_INLINE static bool tooCold(const int16_t temp) { return allow_cold_extrude ? false : temp < extrude_min_temp; } FORCE_INLINE static bool tooCold(const int16_t temp) { return allow_cold_extrude ? false : temp < extrude_min_temp; }
FORCE_INLINE static bool tooColdToExtrude(const uint8_t e) { FORCE_INLINE static bool tooColdToExtrude(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
return tooCold(degHotend(HOTEND_INDEX)); return tooCold(degHotend(HOTEND_INDEX));
} }
FORCE_INLINE static bool targetTooColdToExtrude(const uint8_t e) { FORCE_INLINE static bool targetTooColdToExtrude(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
return tooCold(degTargetHotend(HOTEND_INDEX)); return tooCold(degTargetHotend(HOTEND_INDEX));
} }
#else #else
@ -197,6 +290,16 @@ class Temperature {
FORCE_INLINE static bool hotEnoughToExtrude(const uint8_t e) { return !tooColdToExtrude(e); } FORCE_INLINE static bool hotEnoughToExtrude(const uint8_t e) { return !tooColdToExtrude(e); }
FORCE_INLINE static bool targetHotEnoughToExtrude(const uint8_t e) { return !targetTooColdToExtrude(e); } FORCE_INLINE static bool targetHotEnoughToExtrude(const uint8_t e) { return !targetTooColdToExtrude(e); }
#if HEATER_IDLE_HANDLER
static heater_idle_t hotend_idle[HOTENDS];
#if HAS_HEATED_BED
static heater_idle_t bed_idle;
#endif
#if HAS_HEATED_CHAMBER
static heater_idle_t chamber_idle;
#endif
#endif
private: private:
#if EARLY_WATCHDOG #if EARLY_WATCHDOG
@ -204,11 +307,9 @@ class Temperature {
#endif #endif
static volatile bool temp_meas_ready; static volatile bool temp_meas_ready;
static uint16_t raw_temp_value[MAX_EXTRUDERS];
#if WATCH_HOTENDS #if WATCH_HOTENDS
static uint16_t watch_target_temp[HOTENDS]; static heater_watch_t watch_hotend[HOTENDS];
static millis_t watch_heater_next_ms[HOTENDS];
#endif #endif
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
@ -217,42 +318,40 @@ class Temperature {
#endif #endif
#if ENABLED(PID_EXTRUSION_SCALING) #if ENABLED(PID_EXTRUSION_SCALING)
static long last_e_position; static int32_t last_e_position, lpq[LPQ_MAX_LEN];
static long lpq[LPQ_MAX_LEN]; static lpq_ptr_t lpq_ptr;
static int lpq_ptr;
#endif #endif
// Init min and max temp with extreme values to prevent false errors during startup static temp_range_t temp_range[HOTENDS];
static int16_t minttemp_raw[HOTENDS],
maxttemp_raw[HOTENDS],
minttemp[HOTENDS],
maxttemp[HOTENDS];
#if HAS_HEATED_BED #if HAS_HEATED_BED
static uint16_t raw_temp_bed_value; #if WATCH_BED
#if WATCH_THE_BED static heater_watch_t watch_bed;
static uint16_t watch_target_bed_temp;
static millis_t watch_bed_next_ms;
#endif #endif
#if DISABLED(PIDTEMPBED) #if DISABLED(PIDTEMPBED)
static millis_t next_bed_check_ms; static millis_t next_bed_check_ms;
#endif #endif
#if HEATER_IDLE_HANDLER
static millis_t bed_idle_timeout_ms;
static bool bed_idle_timeout_exceeded;
#endif
#ifdef BED_MINTEMP #ifdef BED_MINTEMP
static int16_t bed_minttemp_raw; static int16_t mintemp_raw_BED;
#endif #endif
#ifdef BED_MAXTEMP #ifdef BED_MAXTEMP
static int16_t bed_maxttemp_raw; static int16_t maxtemp_raw_BED;
#endif #endif
#endif #endif
#if HAS_TEMP_CHAMBER #if HAS_HEATED_CHAMBER
static uint16_t raw_temp_chamber_value; #if WATCH_CHAMBER
static float current_temperature_chamber; static heater_watch_t watch_chamber;
static int16_t current_temperature_chamber_raw; #endif
#if DISABLED(PIDTEMPCHAMBER)
static millis_t next_chamber_check_ms;
#endif
#ifdef CHAMBER_MINTEMP
static int16_t mintemp_raw_CHAMBER;
#endif
#ifdef CHAMBER_MAXTEMP
static int16_t maxtemp_raw_CHAMBER;
#endif
#endif #endif
#ifdef MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED #ifdef MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED
@ -279,11 +378,6 @@ class Temperature {
static bool paused; static bool paused;
#endif #endif
#if HEATER_IDLE_HANDLER
static millis_t heater_idle_timeout_ms[HOTENDS];
static bool heater_idle_timeout_exceeded[HOTENDS];
#endif
public: public:
#if HAS_ADC_BUTTONS #if HAS_ADC_BUTTONS
static uint32_t current_ADCKey_raw; static uint32_t current_ADCKey_raw;
@ -311,7 +405,7 @@ class Temperature {
static float analog_to_celsius_bed(const int raw); static float analog_to_celsius_bed(const int raw);
#endif #endif
#if HAS_TEMP_CHAMBER #if HAS_TEMP_CHAMBER
static float analog_to_celsiusChamber(const int raw); static float analog_to_celsius_chamber(const int raw);
#endif #endif
#if FAN_COUNT > 0 #if FAN_COUNT > 0
@ -395,21 +489,15 @@ class Temperature {
*/ */
#ifdef MILLISECONDS_PREHEAT_TIME #ifdef MILLISECONDS_PREHEAT_TIME
static bool is_preheating(const uint8_t e) { static bool is_preheating(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
return preheat_end_time[HOTEND_INDEX] && PENDING(millis(), preheat_end_time[HOTEND_INDEX]); return preheat_end_time[HOTEND_INDEX] && PENDING(millis(), preheat_end_time[HOTEND_INDEX]);
} }
static void start_preheat_time(const uint8_t e) { static void start_preheat_time(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
preheat_end_time[HOTEND_INDEX] = millis() + MILLISECONDS_PREHEAT_TIME; preheat_end_time[HOTEND_INDEX] = millis() + MILLISECONDS_PREHEAT_TIME;
} }
static void reset_preheat_time(const uint8_t e) { static void reset_preheat_time(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
preheat_end_time[HOTEND_INDEX] = 0; preheat_end_time[HOTEND_INDEX] = 0;
} }
#else #else
@ -427,63 +515,81 @@ class Temperature {
//deg=degreeCelsius //deg=degreeCelsius
FORCE_INLINE static float degHotend(const uint8_t e) { FORCE_INLINE static float degHotend(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].current;
#endif
return current_temperature[HOTEND_INDEX];
} }
#if ENABLED(SHOW_TEMP_ADC_VALUES) #if ENABLED(SHOW_TEMP_ADC_VALUES)
FORCE_INLINE static int16_t rawHotendTemp(const uint8_t e) { FORCE_INLINE static int16_t rawHotendTemp(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].raw;
#endif
return current_temperature_raw[HOTEND_INDEX];
} }
#endif #endif
FORCE_INLINE static int16_t degTargetHotend(const uint8_t e) { FORCE_INLINE static int16_t degTargetHotend(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].target;
#endif
return target_temperature[HOTEND_INDEX];
} }
#if WATCH_HOTENDS #if WATCH_HOTENDS
static void start_watching_heater(const uint8_t e = 0); static void start_watching_heater(const uint8_t e=0);
#else
static inline void start_watching_heater(const uint8_t e=0) { UNUSED(e); }
#endif
#if HAS_LCD_MENU
static inline void start_watching_E0() { start_watching_heater(0); }
static inline void start_watching_E1() { start_watching_heater(1); }
static inline void start_watching_E2() { start_watching_heater(2); }
static inline void start_watching_E3() { start_watching_heater(3); }
static inline void start_watching_E4() { start_watching_heater(4); }
static inline void start_watching_E5() { start_watching_heater(5); }
#endif #endif
static void setTargetHotend(const int16_t celsius, const uint8_t e) { static void setTargetHotend(const int16_t celsius, const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
#ifdef MILLISECONDS_PREHEAT_TIME #ifdef MILLISECONDS_PREHEAT_TIME
if (celsius == 0) if (celsius == 0)
reset_preheat_time(HOTEND_INDEX); reset_preheat_time(HOTEND_INDEX);
else if (target_temperature[HOTEND_INDEX] == 0) else if (temp_hotend[HOTEND_INDEX].target == 0)
start_preheat_time(HOTEND_INDEX); start_preheat_time(HOTEND_INDEX);
#endif #endif
#if ENABLED(AUTO_POWER_CONTROL) #if ENABLED(AUTO_POWER_CONTROL)
powerManager.power_on(); powerManager.power_on();
#endif #endif
target_temperature[HOTEND_INDEX] = MIN(celsius, maxttemp[HOTEND_INDEX] - 15); temp_hotend[HOTEND_INDEX].target = MIN(celsius, temp_range[HOTEND_INDEX].maxtemp - 15);
#if WATCH_HOTENDS start_watching_heater(HOTEND_INDEX);
start_watching_heater(HOTEND_INDEX);
#endif
} }
#if WATCH_CHAMBER
static void start_watching_chamber();
#else
static inline void start_watching_chamber() {}
#endif
#if HAS_TEMP_CHAMBER
static void setTargetChamber(const int16_t celsius) {
#if HAS_HEATED_CHAMBER
temp_chamber.target =
#ifdef CHAMBER_MAXTEMP
min(celsius, CHAMBER_MAXTEMP)
#else
celsius
#endif
;
start_watching_chamber();
#endif // HAS_HEATED_CHAMBER
}
#endif // HAS_TEMP_CHAMBER
FORCE_INLINE static bool isHeatingHotend(const uint8_t e) { FORCE_INLINE static bool isHeatingHotend(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].target > temp_hotend[HOTEND_INDEX].current;
#endif
return target_temperature[HOTEND_INDEX] > current_temperature[HOTEND_INDEX];
} }
FORCE_INLINE static bool isCoolingHotend(const uint8_t e) { FORCE_INLINE static bool isCoolingHotend(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].target < temp_hotend[HOTEND_INDEX].current;
#endif
return target_temperature[HOTEND_INDEX] < current_temperature[HOTEND_INDEX];
} }
#if HAS_TEMP_HOTEND #if HAS_TEMP_HOTEND
@ -497,33 +603,33 @@ class Temperature {
#if HAS_HEATED_BED #if HAS_HEATED_BED
#if ENABLED(SHOW_TEMP_ADC_VALUES) #if ENABLED(SHOW_TEMP_ADC_VALUES)
FORCE_INLINE static int16_t rawBedTemp() { return current_temperature_bed_raw; } FORCE_INLINE static int16_t rawBedTemp() { return temp_bed.raw; }
#endif
FORCE_INLINE static float degBed() { return temp_bed.current; }
FORCE_INLINE static int16_t degTargetBed() { return temp_bed.target; }
FORCE_INLINE static bool isHeatingBed() { return temp_bed.target > temp_bed.current; }
FORCE_INLINE static bool isCoolingBed() { return temp_bed.target < temp_bed.current; }
#if WATCH_BED
static void start_watching_bed();
#else
static inline void start_watching_bed() {}
#endif #endif
FORCE_INLINE static float degBed() { return current_temperature_bed; }
FORCE_INLINE static int16_t degTargetBed() { return target_temperature_bed; }
FORCE_INLINE static bool isHeatingBed() { return target_temperature_bed > current_temperature_bed; }
FORCE_INLINE static bool isCoolingBed() { return target_temperature_bed < current_temperature_bed; }
static void setTargetBed(const int16_t celsius) { static void setTargetBed(const int16_t celsius) {
#if ENABLED(AUTO_POWER_CONTROL) #if ENABLED(AUTO_POWER_CONTROL)
powerManager.power_on(); powerManager.power_on();
#endif #endif
target_temperature_bed = temp_bed.target =
#ifdef BED_MAXTEMP #ifdef BED_MAXTEMP
MIN(celsius, BED_MAXTEMP - 15) MIN(celsius, BED_MAXTEMP - 15)
#else #else
celsius celsius
#endif #endif
; ;
#if WATCH_THE_BED start_watching_bed();
start_watching_bed();
#endif
} }
#if WATCH_THE_BED
static void start_watching_bed();
#endif
static bool wait_for_bed(const bool no_wait_for_cooling=true static bool wait_for_bed(const bool no_wait_for_cooling=true
#if G26_CLICK_CAN_CANCEL #if G26_CLICK_CAN_CANCEL
, const bool click_to_cancel=false , const bool click_to_cancel=false
@ -534,10 +640,15 @@ class Temperature {
#if HAS_TEMP_CHAMBER #if HAS_TEMP_CHAMBER
#if ENABLED(SHOW_TEMP_ADC_VALUES) #if ENABLED(SHOW_TEMP_ADC_VALUES)
FORCE_INLINE static int16_t rawChamberTemp() { return current_temperature_chamber_raw; } FORCE_INLINE static int16_t rawChamberTemp() { return temp_chamber.raw; }
#endif #endif
FORCE_INLINE static float degChamber() { return current_temperature_chamber; } FORCE_INLINE static float degChamber() { return temp_chambercurrent; }
#endif #if HAS_HEATED_CHAMBER
FORCE_INLINE static bool isHeatingChamber() { return temp_chamber.target > temp_chambercurrent; }
FORCE_INLINE static bool isCoolingChamber() { return temp_chamber.target < temp_chambercurrent; }
FORCE_INLINE static int16_t degTargetChamber() {return temp_chamber.target; }
#endif
#endif // HAS_TEMP_CHAMBER
FORCE_INLINE static bool still_heating(const uint8_t e) { FORCE_INLINE static bool still_heating(const uint8_t e) {
return degTargetHotend(e) > TEMP_HYSTERESIS && ABS(degHotend(e) - degTargetHotend(e)) > TEMP_HYSTERESIS; return degTargetHotend(e) > TEMP_HYSTERESIS && ABS(degHotend(e) - degTargetHotend(e)) > TEMP_HYSTERESIS;
@ -589,47 +700,17 @@ class Temperature {
#if HEATER_IDLE_HANDLER #if HEATER_IDLE_HANDLER
static void start_heater_idle_timer(const uint8_t e, const millis_t timeout_ms) {
#if HOTENDS == 1
UNUSED(e);
#endif
heater_idle_timeout_ms[HOTEND_INDEX] = millis() + timeout_ms;
heater_idle_timeout_exceeded[HOTEND_INDEX] = false;
}
static void reset_heater_idle_timer(const uint8_t e) { static void reset_heater_idle_timer(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); hotend_idle[HOTEND_INDEX].reset();
#endif start_watching_heater(HOTEND_INDEX);
heater_idle_timeout_ms[HOTEND_INDEX] = 0;
heater_idle_timeout_exceeded[HOTEND_INDEX] = false;
#if WATCH_HOTENDS
start_watching_heater(HOTEND_INDEX);
#endif
}
FORCE_INLINE static bool is_heater_idle(const uint8_t e) {
#if HOTENDS == 1
UNUSED(e);
#endif
return heater_idle_timeout_exceeded[HOTEND_INDEX];
} }
#if HAS_HEATED_BED #if HAS_HEATED_BED
static void start_bed_idle_timer(const millis_t timeout_ms) {
bed_idle_timeout_ms = millis() + timeout_ms;
bed_idle_timeout_exceeded = false;
}
static void reset_bed_idle_timer() { static void reset_bed_idle_timer() {
bed_idle_timeout_ms = 0; bed_idle.reset();
bed_idle_timeout_exceeded = false; start_watching_bed();
#if WATCH_THE_BED
start_watching_bed();
#endif
} }
FORCE_INLINE static bool is_bed_idle() { return bed_idle_timeout_exceeded; }
#endif #endif
#endif // HEATER_IDLE_HANDLER #endif // HEATER_IDLE_HANDLER
@ -689,25 +770,37 @@ class Temperature {
static float get_pid_output_bed(); static float get_pid_output_bed();
#endif #endif
#if HAS_HEATED_CHAMBER
static float get_pid_output_chamber();
#endif
static void _temp_error(const int8_t e, PGM_P const serial_msg, PGM_P const lcd_msg); static void _temp_error(const int8_t e, PGM_P const serial_msg, PGM_P const lcd_msg);
static void min_temp_error(const int8_t e); static void min_temp_error(const int8_t e);
static void max_temp_error(const int8_t e); static void max_temp_error(const int8_t e);
#if HAS_TEMP_CHAMBER
static void chamber_temp_error(const bool max);
#endif
#if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED #if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED || ENABLED(THERMAL_PROTECTION_CHAMBER)
enum TRState : char { TRInactive, TRFirstHeating, TRStable, TRRunaway }; enum TRState : char { TRInactive, TRFirstHeating, TRStable, TRRunaway };
static void thermal_runaway_protection(TRState * const state, millis_t * const timer, const float &current, const float &target, const int8_t heater_id, const uint16_t period_seconds, const uint16_t hysteresis_degc); typedef struct {
millis_t timer = 0;
TRState state = TRInactive;
} tr_state_machine_t;
#if ENABLED(THERMAL_PROTECTION_HOTENDS) #if ENABLED(THERMAL_PROTECTION_HOTENDS)
static TRState thermal_runaway_state_machine[HOTENDS]; static tr_state_machine_t tr_state_machine[HOTENDS];
static millis_t thermal_runaway_timer[HOTENDS]; #endif
#if HAS_THERMALLY_PROTECTED_BED
static tr_state_machine_t tr_state_machine_bed;
#endif
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
static tr_state_machine_t tr_state_machine_chamber;
#endif #endif
#if HAS_THERMALLY_PROTECTED_BED static void thermal_runaway_protection(tr_state_machine_t &state, const float &current, const float &target, const int8_t heater_id, const uint16_t period_seconds, const uint16_t hysteresis_degc);
static TRState thermal_runaway_bed_state_machine;
static millis_t thermal_runaway_bed_timer;
#endif
#endif // THERMAL_PROTECTION #endif // THERMAL_PROTECTION
}; };

4
Marlin/src/module/thermistor/thermistor_20.h
View File

@ -43,6 +43,10 @@
#define HEATER_4_RAW_HI_TEMP 16383 #define HEATER_4_RAW_HI_TEMP 16383
#define HEATER_4_RAW_LO_TEMP 0 #define HEATER_4_RAW_LO_TEMP 0
#endif #endif
#if THERMISTORHEATER_5 == 20
#define HEATER_5_RAW_HI_TEMP 16383
#define HEATER_5_RAW_LO_TEMP 0
#endif
#if THERMISTORBED == 20 #if THERMISTORBED == 20
#define HEATER_BED_RAW_HI_TEMP 16383 #define HEATER_BED_RAW_HI_TEMP 16383
#define HEATER_BED_RAW_LO_TEMP 0 #define HEATER_BED_RAW_LO_TEMP 0

11
Marlin/src/module/thermistor/thermistors.h
View File

@ -26,7 +26,7 @@
#define OVERSAMPLENR 16 #define OVERSAMPLENR 16
#define OV(N) int16_t((N) * (OVERSAMPLENR)) #define OV(N) int16_t((N) * (OVERSAMPLENR))
#define ANY_THERMISTOR_IS(n) (THERMISTORHEATER_0 == n || THERMISTORHEATER_1 == n || THERMISTORHEATER_2 == n || THERMISTORHEATER_3 == n || THERMISTORHEATER_4 == n || THERMISTORBED == n || THERMISTORCHAMBER == n) #define ANY_THERMISTOR_IS(n) (THERMISTORHEATER_0 == n || THERMISTORHEATER_1 == n || THERMISTORHEATER_2 == n || THERMISTORHEATER_3 == n || THERMISTORHEATER_4 == n || THERMISTORHEATER_5 == n || THERMISTORBED == n || THERMISTORCHAMBER == n)
// Pt1000 and Pt100 handling // Pt1000 and Pt100 handling
// //
@ -272,6 +272,15 @@ static_assert(HEATER_0_TEMPTABLE_LEN < 256 && HEATER_1_TEMPTABLE_LEN < 256 && HE
#define HEATER_4_RAW_LO_TEMP 0 #define HEATER_4_RAW_LO_TEMP 0
#endif #endif
#endif #endif
#ifndef HEATER_5_RAW_HI_TEMP
#ifdef HEATER_5_USES_THERMISTOR
#define HEATER_5_RAW_HI_TEMP 0
#define HEATER_5_RAW_LO_TEMP 16383
#else
#define HEATER_5_RAW_HI_TEMP 16383
#define HEATER_5_RAW_LO_TEMP 0
#endif
#endif
#ifndef HEATER_BED_RAW_HI_TEMP #ifndef HEATER_BED_RAW_HI_TEMP
#ifdef HEATER_BED_USES_THERMISTOR #ifdef HEATER_BED_USES_THERMISTOR
#define HEATER_BED_RAW_HI_TEMP 0 #define HEATER_BED_RAW_HI_TEMP 0

2
Marlin/src/module/tool_change.cpp
View File

@ -838,7 +838,7 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
thermalManager.fan_speed[0] = singlenozzle_fan_speed[tmp_extruder]; thermalManager.fan_speed[0] = singlenozzle_fan_speed[tmp_extruder];
#endif #endif
singlenozzle_temp[active_extruder] = thermalManager.target_temperature[0]; singlenozzle_temp[active_extruder] = thermalManager.temp_hotend[0].target;
if (singlenozzle_temp[tmp_extruder] && singlenozzle_temp[tmp_extruder] != singlenozzle_temp[active_extruder]) { if (singlenozzle_temp[tmp_extruder] && singlenozzle_temp[tmp_extruder] != singlenozzle_temp[active_extruder]) {
thermalManager.setTargetHotend(singlenozzle_temp[tmp_extruder], 0); thermalManager.setTargetHotend(singlenozzle_temp[tmp_extruder], 0);
#if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI) #if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)

2
buildroot/share/tests/LPC1768-tests
View File

@ -37,7 +37,7 @@ opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_1 -1 opt_set TEMP_SENSOR_1 -1
opt_set TEMP_SENSOR_BED 5 opt_set TEMP_SENSOR_BED 5
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \ opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY \ FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY PID_EXTRUSION_SCALING \
FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \ FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \ BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \
PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \ PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \

7
buildroot/share/tests/megaatmega2560-tests
View File

@ -26,9 +26,10 @@ opt_set MOTHERBOARD BOARD_RAMPS_14_EEB
opt_set EXTRUDERS 2 opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_0 -2 opt_set TEMP_SENSOR_0 -2
opt_set TEMP_SENSOR_1 1 opt_set TEMP_SENSOR_1 1
opt_set TEMP_SENSOR_BED 1 opt_set TEMP_SENSOR_BED 2
opt_set POWER_SUPPLY 1 opt_set POWER_SUPPLY 1
opt_set GRID_MAX_POINTS_X 16 opt_set GRID_MAX_POINTS_X 16
opt_set FANMUX0_PIN 53
opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING \ opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING \
SDSUPPORT EEPROM_SETTINGS REPRAP_DISCOUNT_SMART_CONTROLLER \ SDSUPPORT EEPROM_SETTINGS REPRAP_DISCOUNT_SMART_CONTROLLER \
BLINKM PCA9632 RGB_LED NEOPIXEL_LED AUTO_POWER_CONTROL \ BLINKM PCA9632 RGB_LED NEOPIXEL_LED AUTO_POWER_CONTROL \
@ -39,7 +40,9 @@ opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING \
POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE BINARY_FILE_TRANSFER \ POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE BINARY_FILE_TRANSFER \
LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST PINS_DEBUGGING \ LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST PINS_DEBUGGING \
MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING BACKLASH_COMPENSATION BACKLASH_GCODE MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING BACKLASH_COMPENSATION BACKLASH_GCODE
opt_set FANMUX0_PIN 53 opt_enable SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER
opt_set TEMP_SENSOR_CHAMBER 3
opt_add CHAMBER_HEATER_PIN 45
exec_test $1 $2 "RAMPS with 2 extruders, RRDFGSC, Linear ABL, LEDs, and many options" exec_test $1 $2 "RAMPS with 2 extruders, RRDFGSC, Linear ABL, LEDs, and many options"
# #

2
config/default/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/default/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/3DFabXYZ/Migbot/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -550,6 +551,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/3DFabXYZ/Migbot/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/AlephObjects/TAZ4/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 7 #define TEMP_SENSOR_BED 7
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -565,6 +566,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/AlephObjects/TAZ4/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/AliExpress/CL-260/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

2
config/examples/AliExpress/UM2pExt/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 20 #define TEMP_SENSOR_BED 20
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -556,6 +557,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/AliExpress/UM2pExt/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Anet/A2/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Anet/A2/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Anet/A2plus/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Anet/A2plus/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Anet/A6/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 11 #define TEMP_SENSOR_BED 11
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -565,6 +566,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Anet/A6/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Anet/A8/Configuration.h
View File

@ -378,6 +378,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -558,6 +559,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Anet/A8/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/AnyCubic/i3/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -555,6 +556,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/AnyCubic/i3/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/ArmEd/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 13 #define TEMP_SENSOR_BED 13
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -546,6 +547,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/ArmEd/Configuration_adv.h
View File

@ -116,6 +116,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Azteeg/X5GT/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

2
config/examples/BIBO/TouchX/cyclops/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 1 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 1 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/BIBO/TouchX/default/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 60 #define TEMP_SENSOR_BED 60
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BIBO/TouchX/default/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/BQ/Hephestos/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -533,6 +534,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BQ/Hephestos/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/BQ/Hephestos_2/Configuration.h
View File

@ -385,6 +385,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -546,6 +547,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BQ/Hephestos_2/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/BQ/WITBOX/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -533,6 +534,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BQ/WITBOX/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Cartesio/Configuration.h
View File

@ -378,6 +378,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -544,6 +545,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Cartesio/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-10/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -555,6 +556,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-10/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-10S/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-10S/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-10_5S/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-10_5S/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-10mini/Configuration.h
View File

@ -386,6 +386,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -564,6 +565,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-10mini/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-8/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -555,6 +556,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-8/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/Ender-2/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -549,6 +550,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/Ender-2/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/Ender-3/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -549,6 +550,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/Ender-3/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/Ender-4/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -555,6 +556,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/Ender-4/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Einstart-S/Configuration.h
View File

@ -379,6 +379,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -553,6 +554,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Einstart-S/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Felix/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -526,6 +527,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Felix/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Felix/DUAL/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -526,6 +527,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

2
config/examples/FlashForge/CreatorPro/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -535,6 +536,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/FlashForge/CreatorPro/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/FolgerTech/i3-2020/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -550,6 +551,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/FolgerTech/i3-2020/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Formbot/Raptor/Configuration.h
View File

@ -422,6 +422,7 @@
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#endif #endif
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -597,6 +598,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Formbot/Raptor/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Formbot/T_Rex_2+/Configuration.h
View File

@ -392,6 +392,7 @@
#endif #endif
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -574,6 +575,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Formbot/T_Rex_2+/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Formbot/T_Rex_3/Configuration.h
View File

@ -386,6 +386,7 @@
#endif #endif
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -554,6 +555,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Formbot/T_Rex_3/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Geeetech/A10M/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -528,6 +529,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Geeetech/A10M/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Geeetech/A20M/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -528,6 +529,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Geeetech/A20M/Configuration_adv.h
View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Geeetech/GT2560/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -560,6 +561,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

2
config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

Some files were not shown because too many files have changed in this diff Show More