Support for Z-Bold board (#14024)
This commit is contained in:
Aliaksei Kvitsinski
Scott Lahteine
parent
18904c42f6
commit
648a91bce8
@ -237,6 +237,8 @@ else ifeq ($(HARDWARE_MOTHERBOARD),31)
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),441)
|
||||
# TRONXY V3 1.0
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),442)
|
||||
# Z-Bolt X Series
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),550)
|
||||
|
||||
#
|
||||
# Other ATmega1280, ATmega2560
|
||||
@ -288,6 +290,8 @@ else ifeq ($(HARDWARE_MOTHERBOARD),75)
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),76)
|
||||
# Geeetech GT2560 Rev B for A20(M/D)
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),86)
|
||||
# Einstart retrofit
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),666)
|
||||
|
||||
#
|
||||
# ATmega1281, ATmega2561
|
||||
|
||||
@ -91,6 +91,7 @@
|
||||
#define BOARD_DUPLICATOR_I3_PLUS 31 // Wanhao Duplicator i3 Plus
|
||||
#define BOARD_VORON 441 // VORON Design
|
||||
#define BOARD_TRONXY_V3_1_0 442 // Tronxy TRONXY-V3-1.0
|
||||
#define BOARD_Z_BOLT_X_SERIES 550 // Z-Bolt X Series
|
||||
|
||||
//
|
||||
// Other ATmega1280, ATmega2560
|
||||
|
||||
@ -170,6 +170,8 @@
|
||||
#include "pins_VORON.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(TRONXY_V3_1_0)
|
||||
#include "pins_TRONXY_V3_1_0.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(Z_BOLT_X_SERIES)
|
||||
#include "pins_Z_BOLT_X_SERIES.h" // ATmega2560 env:megaatmega2560
|
||||
|
||||
//
|
||||
// Other ATmega1280, ATmega2560
|
||||
|
||||
@ -42,28 +42,28 @@
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#define X_STOP_PIN 44 // 2560 PIN 40
|
||||
#define Y_STOP_PIN 43 // 2560 PIN 41
|
||||
#define Z_STOP_PIN 42 // 2560 PIN 42
|
||||
#define X_STOP_PIN 44
|
||||
#define Y_STOP_PIN 43
|
||||
#define Z_STOP_PIN 42
|
||||
|
||||
//
|
||||
// Steppers
|
||||
//
|
||||
#define X_STEP_PIN 76 // 2560 PIN 68
|
||||
#define X_DIR_PIN 75 // 2560 PIN 67
|
||||
#define X_ENABLE_PIN 73 // 2560 PIN 66
|
||||
#define X_STEP_PIN 76
|
||||
#define X_DIR_PIN 75
|
||||
#define X_ENABLE_PIN 73
|
||||
|
||||
#define Y_STEP_PIN 31 // 2560 PIN 59
|
||||
#define Y_DIR_PIN 32 // 2560 PIN 58
|
||||
#define Y_ENABLE_PIN 72 // 2560 PIN 65
|
||||
#define Y_STEP_PIN 31
|
||||
#define Y_DIR_PIN 32
|
||||
#define Y_ENABLE_PIN 72
|
||||
|
||||
#define Z_STEP_PIN 34 // 2560 PIN 56
|
||||
#define Z_DIR_PIN 35 // 2560 PIN 55
|
||||
#define Z_ENABLE_PIN 33 // 2560 PIN 57
|
||||
#define Z_STEP_PIN 34
|
||||
#define Z_DIR_PIN 35
|
||||
#define Z_ENABLE_PIN 33
|
||||
|
||||
#define E0_STEP_PIN 36 // 2560 PIN 54
|
||||
#define E0_DIR_PIN 37 // 2560 PIN 53
|
||||
#define E0_ENABLE_PIN 30 // 2560 PIN 60
|
||||
#define E0_STEP_PIN 36
|
||||
#define E0_DIR_PIN 37
|
||||
#define E0_ENABLE_PIN 30
|
||||
|
||||
//
|
||||
// Temperature Sensors
|
||||
@ -74,16 +74,16 @@
|
||||
//
|
||||
// Heaters / Fans
|
||||
//
|
||||
#define HEATER_0_PIN 83 // 2560 PIN 49
|
||||
#define HEATER_BED_PIN 38 // 2560 PIN 50
|
||||
#define HEATER_0_PIN 83
|
||||
#define HEATER_BED_PIN 38
|
||||
|
||||
#define FAN_PIN 82 // 2560 PIN 48
|
||||
#define FAN_PIN 82
|
||||
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
#define SDSS 53 // 2560 PIN 19
|
||||
#define LED_PIN 4 // 2560 PIN 1
|
||||
#define SDSS 53
|
||||
#define LED_PIN 4
|
||||
|
||||
//////////////////////////
|
||||
// LCDs and Controllers //
|
||||
@ -97,24 +97,24 @@
|
||||
// u8glib constructor
|
||||
// U8GLIB_SH1106_128X64 u8g(DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, LCD_PINS_DC, LCD_PINS_RS);
|
||||
|
||||
#define LCD_PINS_DC 78 // 2560 PIN 4
|
||||
#define LCD_PINS_RS 79 // 2560 PIN 8
|
||||
#define LCD_PINS_DC 78
|
||||
#define LCD_PINS_RS 79
|
||||
// DOGM SPI LCD Support
|
||||
#define DOGLCD_CS 3 // 2560 PIN 7
|
||||
#define DOGLCD_MOSI 2 // 2560 PIN 6
|
||||
#define DOGLCD_SCK 5 // 2560 PIN 5
|
||||
#define DOGLCD_A0 2 // 2560 PIN 6
|
||||
#define DOGLCD_CS 3
|
||||
#define DOGLCD_MOSI 2
|
||||
#define DOGLCD_SCK 5
|
||||
#define DOGLCD_A0 2
|
||||
|
||||
//
|
||||
// LCD Display input pins
|
||||
//
|
||||
#define BTN_UP 25 // 2560 PIN 75
|
||||
#define BTN_DWN 26 // 2560 PIN 74
|
||||
#define BTN_LFT 27 // 2560 PIN 73
|
||||
#define BTN_RT 28 // 2560 PIN 72
|
||||
#define BTN_UP 25
|
||||
#define BTN_DWN 26
|
||||
#define BTN_LFT 27
|
||||
#define BTN_RT 28
|
||||
|
||||
// 'OK' button
|
||||
#define BTN_ENC 29 // 2560 PIN 71
|
||||
#define BTN_ENC 29
|
||||
|
||||
// Set Kill to right arrow, same as RIGID_PANEL
|
||||
#define KILL_PIN 28 // 2560 PIN 72
|
||||
#define KILL_PIN 28
|
||||
|
||||
257
Marlin/src/pins/pins_Z_BOLT_X_SERIES.h
Normal file
257
Marlin/src/pins/pins_Z_BOLT_X_SERIES.h
Normal file
@ -0,0 +1,257 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Z-Bolt X Series board – based on Arduino Mega2560
|
||||
*/
|
||||
|
||||
#if HOTENDS > 4 || E_STEPPERS > 4
|
||||
#error "Z-Bolt X Series board supports up to 4 hotends / E-steppers."
|
||||
#endif
|
||||
|
||||
#define BOARD_NAME "Z-Bolt X Series"
|
||||
|
||||
#if ENABLED(TARGET_LPC1768)
|
||||
#error "Oops! Set MOTHERBOARD to an LPC1768-based board when building for LPC1768."
|
||||
#elif defined(__STM32F1__)
|
||||
#error "Oops! Set MOTHERBOARD to an STM32F1-based board when building for STM32F1."
|
||||
#endif
|
||||
|
||||
#if DISABLED(IS_RAMPS_SMART, IS_RAMPS_DUO, IS_RAMPS4DUE, TARGET_LPC1768)
|
||||
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
|
||||
#error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//
|
||||
// Servos
|
||||
//
|
||||
#ifndef SERVO0_PIN
|
||||
#define SERVO0_PIN 11
|
||||
#endif
|
||||
#ifndef SERVO3_PIN
|
||||
#define SERVO3_PIN 4
|
||||
#endif
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#define X_MIN_PIN 3
|
||||
#ifndef X_MAX_PIN
|
||||
#define X_MAX_PIN 2
|
||||
#endif
|
||||
#define Y_MIN_PIN 14
|
||||
#define Y_MAX_PIN 15
|
||||
#define Z_MIN_PIN 18
|
||||
#define Z_MAX_PIN 19
|
||||
|
||||
//
|
||||
// Z Probe (when not Z_MIN_PIN)
|
||||
//
|
||||
#ifndef Z_MIN_PROBE_PIN
|
||||
#define Z_MIN_PROBE_PIN 32
|
||||
#endif
|
||||
|
||||
//
|
||||
// Steppers
|
||||
//
|
||||
#define X_STEP_PIN 54
|
||||
#define X_DIR_PIN 55
|
||||
#define X_ENABLE_PIN 38
|
||||
#ifndef X_CS_PIN
|
||||
#define X_CS_PIN -1
|
||||
#endif
|
||||
|
||||
#define Y_STEP_PIN 60
|
||||
#define Y_DIR_PIN 61
|
||||
#define Y_ENABLE_PIN 56
|
||||
#ifndef Y_CS_PIN
|
||||
#define Y_CS_PIN -1
|
||||
#endif
|
||||
|
||||
#define Z_STEP_PIN 46
|
||||
#define Z_DIR_PIN 48
|
||||
#define Z_ENABLE_PIN 62
|
||||
#ifndef Z_CS_PIN
|
||||
#define Z_CS_PIN -1
|
||||
#endif
|
||||
|
||||
#define E0_STEP_PIN 26
|
||||
#define E0_DIR_PIN 28
|
||||
#define E0_ENABLE_PIN 24
|
||||
#ifndef E0_CS_PIN
|
||||
#define E0_CS_PIN -1
|
||||
#endif
|
||||
|
||||
#define E1_STEP_PIN 36
|
||||
#define E1_DIR_PIN 34
|
||||
#define E1_ENABLE_PIN 30
|
||||
#ifndef E1_CS_PIN
|
||||
#define E1_CS_PIN -1
|
||||
#endif
|
||||
|
||||
// Red
|
||||
#define E2_STEP_PIN 42
|
||||
#define E2_DIR_PIN 40
|
||||
#define E2_ENABLE_PIN 65
|
||||
#ifndef E2_CS_PIN
|
||||
#define E2_CS_PIN -1
|
||||
#endif
|
||||
|
||||
// Black
|
||||
#define E3_STEP_PIN 44
|
||||
#define E3_DIR_PIN 64
|
||||
#define E3_ENABLE_PIN 66
|
||||
#ifndef E3_CS_PIN
|
||||
#define E3_CS_PIN -1
|
||||
#endif
|
||||
|
||||
//
|
||||
// Temperature Sensors
|
||||
//
|
||||
#define TEMP_0_PIN 13 // Analog Input
|
||||
#define TEMP_1_PIN 15 // Analog Input
|
||||
#define TEMP_2_PIN 5 // Analog Input (BLACK)
|
||||
#define TEMP_3_PIN 9 // Analog Input (RED)
|
||||
#define TEMP_BED_PIN 14 // Analog Input
|
||||
|
||||
//
|
||||
// Heaters / Fans
|
||||
//
|
||||
#define HEATER_0_PIN 10
|
||||
#define HEATER_1_PIN 7
|
||||
#define HEATER_2_PIN 6
|
||||
#define HEATER_3_PIN 5
|
||||
#define HEATER_BED_PIN 8
|
||||
|
||||
#define FAN_PIN 9
|
||||
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
#define SDSS 53
|
||||
#define LED_PIN 13
|
||||
|
||||
#ifndef FILWIDTH_PIN
|
||||
#define FILWIDTH_PIN 5 // Analog Input on AUX2
|
||||
#endif
|
||||
|
||||
// Оn the servos connector
|
||||
#ifndef FIL_RUNOUT_PIN
|
||||
#define FIL_RUNOUT_PIN 4
|
||||
#endif
|
||||
|
||||
#ifndef PS_ON_PIN
|
||||
#define PS_ON_PIN 12
|
||||
#endif
|
||||
|
||||
#define AUX2_PINS_FREE !( BOTH(ULTRA_LCD, NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD) )
|
||||
|
||||
#if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN) && !defined(SPINDLE_LASER_ENA_PIN)
|
||||
#if NUM_SERVOS <= 1 // try to use servo connector first
|
||||
#define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM
|
||||
#elif AUX2_PINS_FREE
|
||||
#define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA)
|
||||
#if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first
|
||||
#define SPINDLE_LASER_ENA_PIN 4 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 5
|
||||
#elif AUX2_PINS_FREE
|
||||
#define SPINDLE_LASER_ENA_PIN 40 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 65
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#undef AUX2_PINS_FREE
|
||||
|
||||
//
|
||||
// TMC software SPI
|
||||
//
|
||||
#if ENABLED(TMC_USE_SW_SPI)
|
||||
#ifndef TMC_SW_MOSI
|
||||
#define TMC_SW_MOSI 66
|
||||
#endif
|
||||
#ifndef TMC_SW_MISO
|
||||
#define TMC_SW_MISO 44
|
||||
#endif
|
||||
#ifndef TMC_SW_SCK
|
||||
#define TMC_SW_SCK 64
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if HAS_DRIVER(TMC2208)
|
||||
/**
|
||||
* TMC2208 stepper drivers
|
||||
*
|
||||
* Hardware serial communication ports.
|
||||
* If undefined software serial is used according to the pins below
|
||||
*/
|
||||
//#define X_HARDWARE_SERIAL Serial1
|
||||
//#define X2_HARDWARE_SERIAL Serial1
|
||||
//#define Y_HARDWARE_SERIAL Serial1
|
||||
//#define Y2_HARDWARE_SERIAL Serial1
|
||||
//#define Z_HARDWARE_SERIAL Serial1
|
||||
//#define Z2_HARDWARE_SERIAL Serial1
|
||||
//#define E0_HARDWARE_SERIAL Serial1
|
||||
//#define E1_HARDWARE_SERIAL Serial1
|
||||
//#define E2_HARDWARE_SERIAL Serial1
|
||||
//#define E3_HARDWARE_SERIAL Serial1
|
||||
//#define E4_HARDWARE_SERIAL Serial1
|
||||
|
||||
//
|
||||
// Software serial
|
||||
//
|
||||
|
||||
#define X_SERIAL_TX_PIN 40
|
||||
#define X_SERIAL_RX_PIN 63
|
||||
#define X2_SERIAL_TX_PIN -1
|
||||
#define X2_SERIAL_RX_PIN -1
|
||||
|
||||
#define Y_SERIAL_TX_PIN 59
|
||||
#define Y_SERIAL_RX_PIN 64
|
||||
#define Y2_SERIAL_TX_PIN -1
|
||||
#define Y2_SERIAL_RX_PIN -1
|
||||
|
||||
#define Z_SERIAL_TX_PIN 42
|
||||
#define Z_SERIAL_RX_PIN 65
|
||||
#define Z2_SERIAL_TX_PIN -1
|
||||
#define Z2_SERIAL_RX_PIN -1
|
||||
|
||||
#define E0_SERIAL_TX_PIN 44
|
||||
#define E0_SERIAL_RX_PIN 66
|
||||
#define E1_SERIAL_TX_PIN -1
|
||||
#define E1_SERIAL_RX_PIN -1
|
||||
#define E2_SERIAL_TX_PIN -1
|
||||
#define E2_SERIAL_RX_PIN -1
|
||||
#define E3_SERIAL_TX_PIN -1
|
||||
#define E3_SERIAL_RX_PIN -1
|
||||
#define E4_SERIAL_TX_PIN -1
|
||||
#define E4_SERIAL_RX_PIN -1
|
||||
#endif
|
||||
Loading…
Reference in New Issue
Block a user