Allow pullup/downs on power loss pin (#14986)
This commit is contained in:
parent
19e21a8f10
commit
67f8ba6fed
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -886,6 +886,10 @@ void setup() {
|
||||
runout.setup();
|
||||
#endif
|
||||
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
recovery.setup();
|
||||
#endif
|
||||
|
||||
setup_killpin();
|
||||
|
||||
#if HAS_TMC220x
|
||||
|
@ -26,12 +26,16 @@
|
||||
*/
|
||||
|
||||
#include "../sd/cardreader.h"
|
||||
#include "../inc/MarlinConfigPre.h"
|
||||
#include "../inc/MarlinConfig.h"
|
||||
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
#include "../feature/mixing.h"
|
||||
#endif
|
||||
|
||||
#if !defined(POWER_LOSS_STATE) && PIN_EXISTS(POWER_LOSS)
|
||||
#define POWER_LOSS_STATE HIGH
|
||||
#endif
|
||||
|
||||
//#define DEBUG_POWER_LOSS_RECOVERY
|
||||
//#define SAVE_EACH_CMD_MODE
|
||||
//#define SAVE_INFO_INTERVAL_MS 0
|
||||
@ -110,6 +114,20 @@ class PrintJobRecovery {
|
||||
|
||||
static void init();
|
||||
|
||||
static inline void setup() {
|
||||
#if PIN_EXISTS(POWER_LOSS)
|
||||
#if ENABLED(POWER_LOSS_PULL)
|
||||
#if POWER_LOSS_STATE == LOW
|
||||
SET_INPUT_PULLUP(POWER_LOSS_PIN);
|
||||
#else
|
||||
SET_INPUT_PULLDOWN(POWER_LOSS_PIN);
|
||||
#endif
|
||||
#else
|
||||
SET_INPUT(POWER_LOSS_PIN);
|
||||
#endif
|
||||
#endif
|
||||
}
|
||||
|
||||
static bool enabled;
|
||||
static void enable(const bool onoff);
|
||||
static void changed();
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -939,6 +939,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -943,6 +943,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -934,6 +934,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -934,6 +934,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -934,6 +934,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -934,6 +934,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -939,6 +939,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -939,6 +939,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
#define POWER_LOSS_PIN 69 // Pin to detect power loss
|
||||
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
#define POWER_LOSS_PIN 69 // Pin to detect power loss
|
||||
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -940,6 +940,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -940,6 +940,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -936,6 +936,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -934,6 +934,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -931,6 +931,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -934,6 +934,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -934,6 +934,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -948,6 +948,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
#define POWER_LOSS_PIN 65 // Pin to detect power loss
|
||||
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
|
||||
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
|
||||
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -937,6 +937,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
@ -935,6 +935,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
|
Some files were not shown because too many files have changed in this diff Show More
Loading…
Reference in New Issue
Block a user