diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 3138a13ba..943cec5ee 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/Cartesio/Configuration_adv.h b/Marlin/example_configurations/Cartesio/Configuration_adv.h index 5f54f0e75..aa8abaf73 100644 --- a/Marlin/example_configurations/Cartesio/Configuration_adv.h +++ b/Marlin/example_configurations/Cartesio/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index 2e52c39eb..1a43a932f 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 9740e9c75..7093cc035 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h index a7fab871b..dc7bc1d0b 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index c275fa3b6..925395f84 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -321,13 +321,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/K8400/Configuration_adv.h b/Marlin/example_configurations/K8400/Configuration_adv.h index 8ee66df5e..d1c348fa3 100644 --- a/Marlin/example_configurations/K8400/Configuration_adv.h +++ b/Marlin/example_configurations/K8400/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index 92a337ba1..2a9cb42b5 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index 647fb7122..54ed0410d 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h index 0211a9caf..85e5b2779 100644 --- a/Marlin/example_configurations/TAZ4/Configuration_adv.h +++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h @@ -316,13 +316,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 9740e9c75..7093cc035 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h index 114951d57..0b0e71333 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index b3a2039e5..d2adb4cfa 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index b3a2039e5..d2adb4cfa 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h index b438af289..a025d5a16 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h @@ -313,13 +313,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h index a98c53eae..96d2f05be 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index 1f5446dc5..1c3dc6f5b 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index 190c18ce3..1ae59aed0 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -308,13 +308,13 @@ // Remember: you should set the second extruder x-offset to 0 in your slicer. // There are a few selectable movement modes for dual x-carriages using M605 S - // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results - // as long as it supports dual x-carriages. (M605 S0) - // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so - // that additional slicer support is not required. (M605 S1) - // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all - // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at - // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) // This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE