Merge pull request #5448 from thinkyhead/rc_eeprom_bump
EEPROM: Prolong life. Better support for `DISTINCT_E_FACTORS`.
This commit is contained in:
commit
8239c45b30
@ -36,88 +36,89 @@
|
|||||||
*
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
#define EEPROM_VERSION "V27"
|
#define EEPROM_VERSION "V28"
|
||||||
|
|
||||||
// Change EEPROM version if these are changed:
|
// Change EEPROM version if these are changed:
|
||||||
#define EEPROM_OFFSET 100
|
#define EEPROM_OFFSET 100
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* V27 EEPROM Layout:
|
* V28 EEPROM Layout:
|
||||||
*
|
*
|
||||||
* 100 Version (char x4)
|
* 100 Version (char x4)
|
||||||
* 104 EEPROM Checksum (uint16_t)
|
* 104 EEPROM Checksum (uint16_t)
|
||||||
*
|
*
|
||||||
* 106 M92 XYZE planner.axis_steps_per_mm (float x4 ... x7)
|
* 106 E_STEPPERS (uint8_t)
|
||||||
* 122 M203 XYZE planner.max_feedrate_mm_s (float x4 ... x7)
|
* 107 M92 XYZE planner.axis_steps_per_mm (float x4 ... x7)
|
||||||
* 138 M201 XYZE planner.max_acceleration_mm_per_s2 (uint32_t x4 ... x7)
|
* 123 M203 XYZE planner.max_feedrate_mm_s (float x4 ... x7)
|
||||||
* 154 M204 P planner.acceleration (float)
|
* 139 M201 XYZE planner.max_acceleration_mm_per_s2 (uint32_t x4 ... x7)
|
||||||
* 158 M204 R planner.retract_acceleration (float)
|
* 155 M204 P planner.acceleration (float)
|
||||||
* 162 M204 T planner.travel_acceleration (float)
|
* 159 M204 R planner.retract_acceleration (float)
|
||||||
* 166 M205 S planner.min_feedrate_mm_s (float)
|
* 163 M204 T planner.travel_acceleration (float)
|
||||||
* 170 M205 T planner.min_travel_feedrate_mm_s (float)
|
* 167 M205 S planner.min_feedrate_mm_s (float)
|
||||||
* 174 M205 B planner.min_segment_time (ulong)
|
* 171 M205 T planner.min_travel_feedrate_mm_s (float)
|
||||||
* 178 M205 X planner.max_jerk[X_AXIS] (float)
|
* 175 M205 B planner.min_segment_time (ulong)
|
||||||
* 182 M205 Y planner.max_jerk[Y_AXIS] (float)
|
* 179 M205 X planner.max_jerk[X_AXIS] (float)
|
||||||
* 186 M205 Z planner.max_jerk[Z_AXIS] (float)
|
* 183 M205 Y planner.max_jerk[Y_AXIS] (float)
|
||||||
* 190 M205 E planner.max_jerk[E_AXIS] (float)
|
* 187 M205 Z planner.max_jerk[Z_AXIS] (float)
|
||||||
* 194 M206 XYZ home_offset (float x3)
|
* 191 M205 E planner.max_jerk[E_AXIS] (float)
|
||||||
* 206 M218 XYZ hotend_offset (float x3 per additional hotend)
|
* 195 M206 XYZ home_offset (float x3)
|
||||||
|
* 207 M218 XYZ hotend_offset (float x3 per additional hotend)
|
||||||
*
|
*
|
||||||
* Mesh bed leveling:
|
* Mesh bed leveling:
|
||||||
* 218 M420 S status (uint8)
|
* 219 M420 S status (uint8)
|
||||||
* 219 z_offset (float)
|
* 220 z_offset (float)
|
||||||
* 223 mesh_num_x (uint8 as set in firmware)
|
* 224 mesh_num_x (uint8 as set in firmware)
|
||||||
* 224 mesh_num_y (uint8 as set in firmware)
|
* 225 mesh_num_y (uint8 as set in firmware)
|
||||||
* 225 G29 S3 XYZ z_values[][] (float x9, by default, up to float x 81)
|
* 226 G29 S3 XYZ z_values[][] (float x9, by default, up to float x 81)
|
||||||
*
|
*
|
||||||
* AUTO BED LEVELING
|
* AUTO BED LEVELING
|
||||||
* 261 M851 zprobe_zoffset (float)
|
* 262 M851 zprobe_zoffset (float)
|
||||||
*
|
*
|
||||||
* DELTA:
|
* DELTA:
|
||||||
* 265 M666 XYZ endstop_adj (float x3)
|
* 266 M666 XYZ endstop_adj (float x3)
|
||||||
* 277 M665 R delta_radius (float)
|
* 278 M665 R delta_radius (float)
|
||||||
* 281 M665 L delta_diagonal_rod (float)
|
* 282 M665 L delta_diagonal_rod (float)
|
||||||
* 285 M665 S delta_segments_per_second (float)
|
* 286 M665 S delta_segments_per_second (float)
|
||||||
* 289 M665 A delta_diagonal_rod_trim_tower_1 (float)
|
* 290 M665 A delta_diagonal_rod_trim_tower_1 (float)
|
||||||
* 293 M665 B delta_diagonal_rod_trim_tower_2 (float)
|
* 294 M665 B delta_diagonal_rod_trim_tower_2 (float)
|
||||||
* 297 M665 C delta_diagonal_rod_trim_tower_3 (float)
|
* 298 M665 C delta_diagonal_rod_trim_tower_3 (float)
|
||||||
*
|
*
|
||||||
* Z_DUAL_ENDSTOPS:
|
* Z_DUAL_ENDSTOPS:
|
||||||
* 301 M666 Z z_endstop_adj (float)
|
* 302 M666 Z z_endstop_adj (float)
|
||||||
*
|
*
|
||||||
* ULTIPANEL:
|
* ULTIPANEL:
|
||||||
* 305 M145 S0 H lcd_preheat_hotend_temp (int x2)
|
* 306 M145 S0 H lcd_preheat_hotend_temp (int x2)
|
||||||
* 309 M145 S0 B lcd_preheat_bed_temp (int x2)
|
* 310 M145 S0 B lcd_preheat_bed_temp (int x2)
|
||||||
* 313 M145 S0 F lcd_preheat_fan_speed (int x2)
|
* 314 M145 S0 F lcd_preheat_fan_speed (int x2)
|
||||||
*
|
*
|
||||||
* PIDTEMP:
|
* PIDTEMP:
|
||||||
* 317 M301 E0 PIDC Kp[0], Ki[0], Kd[0], Kc[0] (float x4)
|
* 318 M301 E0 PIDC Kp[0], Ki[0], Kd[0], Kc[0] (float x4)
|
||||||
* 333 M301 E1 PIDC Kp[1], Ki[1], Kd[1], Kc[1] (float x4)
|
* 334 M301 E1 PIDC Kp[1], Ki[1], Kd[1], Kc[1] (float x4)
|
||||||
* 349 M301 E2 PIDC Kp[2], Ki[2], Kd[2], Kc[2] (float x4)
|
* 350 M301 E2 PIDC Kp[2], Ki[2], Kd[2], Kc[2] (float x4)
|
||||||
* 365 M301 E3 PIDC Kp[3], Ki[3], Kd[3], Kc[3] (float x4)
|
* 366 M301 E3 PIDC Kp[3], Ki[3], Kd[3], Kc[3] (float x4)
|
||||||
* 381 M301 L lpq_len (int)
|
* 382 M301 L lpq_len (int)
|
||||||
*
|
*
|
||||||
* PIDTEMPBED:
|
* PIDTEMPBED:
|
||||||
* 383 M304 PID thermalManager.bedKp, thermalManager.bedKi, thermalManager.bedKd (float x3)
|
* 384 M304 PID thermalManager.bedKp, thermalManager.bedKi, thermalManager.bedKd (float x3)
|
||||||
*
|
*
|
||||||
* DOGLCD:
|
* DOGLCD:
|
||||||
* 395 M250 C lcd_contrast (int)
|
* 396 M250 C lcd_contrast (int)
|
||||||
*
|
*
|
||||||
* FWRETRACT:
|
* FWRETRACT:
|
||||||
* 397 M209 S autoretract_enabled (bool)
|
* 398 M209 S autoretract_enabled (bool)
|
||||||
* 398 M207 S retract_length (float)
|
* 399 M207 S retract_length (float)
|
||||||
* 402 M207 W retract_length_swap (float)
|
* 403 M207 W retract_length_swap (float)
|
||||||
* 406 M207 F retract_feedrate_mm_s (float)
|
* 407 M207 F retract_feedrate_mm_s (float)
|
||||||
* 410 M207 Z retract_zlift (float)
|
* 411 M207 Z retract_zlift (float)
|
||||||
* 414 M208 S retract_recover_length (float)
|
* 415 M208 S retract_recover_length (float)
|
||||||
* 418 M208 W retract_recover_length_swap (float)
|
* 419 M208 W retract_recover_length_swap (float)
|
||||||
* 422 M208 F retract_recover_feedrate_mm_s (float)
|
* 423 M208 F retract_recover_feedrate_mm_s (float)
|
||||||
*
|
*
|
||||||
* Volumetric Extrusion:
|
* Volumetric Extrusion:
|
||||||
* 426 M200 D volumetric_enabled (bool)
|
* 427 M200 D volumetric_enabled (bool)
|
||||||
* 427 M200 T D filament_size (float x4) (T0..3)
|
* 428 M200 T D filament_size (float x4) (T0..3)
|
||||||
*
|
*
|
||||||
* 443 This Slot is Available!
|
* 444 This Slot is Available!
|
||||||
*
|
*
|
||||||
*/
|
*/
|
||||||
#include "Marlin.h"
|
#include "Marlin.h"
|
||||||
@ -132,33 +133,6 @@
|
|||||||
#include "mesh_bed_leveling.h"
|
#include "mesh_bed_leveling.h"
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
uint16_t eeprom_checksum;
|
|
||||||
const char version[4] = EEPROM_VERSION;
|
|
||||||
|
|
||||||
void _EEPROM_writeData(int &pos, uint8_t* value, uint8_t size) {
|
|
||||||
uint8_t c;
|
|
||||||
while (size--) {
|
|
||||||
eeprom_write_byte((unsigned char*)pos, *value);
|
|
||||||
c = eeprom_read_byte((unsigned char*)pos);
|
|
||||||
if (c != *value) {
|
|
||||||
SERIAL_ECHO_START;
|
|
||||||
SERIAL_ECHOLNPGM(MSG_ERR_EEPROM_WRITE);
|
|
||||||
}
|
|
||||||
eeprom_checksum += c;
|
|
||||||
pos++;
|
|
||||||
value++;
|
|
||||||
};
|
|
||||||
}
|
|
||||||
void _EEPROM_readData(int &pos, uint8_t* value, uint8_t size) {
|
|
||||||
do {
|
|
||||||
uint8_t c = eeprom_read_byte((unsigned char*)pos);
|
|
||||||
*value = c;
|
|
||||||
eeprom_checksum += c;
|
|
||||||
pos++;
|
|
||||||
value++;
|
|
||||||
} while (--size);
|
|
||||||
}
|
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Post-process after Retrieve or Reset
|
* Post-process after Retrieve or Reset
|
||||||
*/
|
*/
|
||||||
@ -188,6 +162,42 @@ void Config_Postprocess() {
|
|||||||
|
|
||||||
#if ENABLED(EEPROM_SETTINGS)
|
#if ENABLED(EEPROM_SETTINGS)
|
||||||
|
|
||||||
|
uint16_t eeprom_checksum;
|
||||||
|
const char version[4] = EEPROM_VERSION;
|
||||||
|
|
||||||
|
bool eeprom_write_error;
|
||||||
|
|
||||||
|
void _EEPROM_writeData(int &pos, uint8_t* value, uint8_t size) {
|
||||||
|
if (eeprom_write_error) return;
|
||||||
|
while (size--) {
|
||||||
|
uint8_t * const p = (uint8_t * const)pos;
|
||||||
|
const uint8_t v = *value;
|
||||||
|
// EEPROM has only ~100,000 write cycles,
|
||||||
|
// so only write bytes that have changed!
|
||||||
|
if (v != eeprom_read_byte(p)) {
|
||||||
|
eeprom_write_byte(p, v);
|
||||||
|
if (eeprom_read_byte(p) != v) {
|
||||||
|
SERIAL_ECHO_START;
|
||||||
|
SERIAL_ECHOLNPGM(MSG_ERR_EEPROM_WRITE);
|
||||||
|
eeprom_write_error = true;
|
||||||
|
return;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
eeprom_checksum += v;
|
||||||
|
pos++;
|
||||||
|
value++;
|
||||||
|
};
|
||||||
|
}
|
||||||
|
void _EEPROM_readData(int &pos, uint8_t* value, uint8_t size) {
|
||||||
|
do {
|
||||||
|
uint8_t c = eeprom_read_byte((unsigned char*)pos);
|
||||||
|
*value = c;
|
||||||
|
eeprom_checksum += c;
|
||||||
|
pos++;
|
||||||
|
value++;
|
||||||
|
} while (--size);
|
||||||
|
}
|
||||||
|
|
||||||
#define DUMMY_PID_VALUE 3000.0f
|
#define DUMMY_PID_VALUE 3000.0f
|
||||||
#define EEPROM_START() int eeprom_index = EEPROM_OFFSET
|
#define EEPROM_START() int eeprom_index = EEPROM_OFFSET
|
||||||
#define EEPROM_SKIP(VAR) eeprom_index += sizeof(VAR)
|
#define EEPROM_SKIP(VAR) eeprom_index += sizeof(VAR)
|
||||||
@ -203,14 +213,19 @@ void Config_Postprocess() {
|
|||||||
|
|
||||||
EEPROM_START();
|
EEPROM_START();
|
||||||
|
|
||||||
|
eeprom_write_error = false;
|
||||||
|
|
||||||
EEPROM_WRITE(ver); // invalidate data first
|
EEPROM_WRITE(ver); // invalidate data first
|
||||||
EEPROM_SKIP(eeprom_checksum); // Skip the checksum slot
|
EEPROM_SKIP(eeprom_checksum); // Skip the checksum slot
|
||||||
|
|
||||||
eeprom_checksum = 0; // clear before first "real data"
|
eeprom_checksum = 0; // clear before first "real data"
|
||||||
|
|
||||||
|
const uint8_t esteppers = E_STEPPERS;
|
||||||
|
EEPROM_WRITE(esteppers);
|
||||||
EEPROM_WRITE(planner.axis_steps_per_mm);
|
EEPROM_WRITE(planner.axis_steps_per_mm);
|
||||||
EEPROM_WRITE(planner.max_feedrate_mm_s);
|
EEPROM_WRITE(planner.max_feedrate_mm_s);
|
||||||
EEPROM_WRITE(planner.max_acceleration_mm_per_s2);
|
EEPROM_WRITE(planner.max_acceleration_mm_per_s2);
|
||||||
|
|
||||||
EEPROM_WRITE(planner.acceleration);
|
EEPROM_WRITE(planner.acceleration);
|
||||||
EEPROM_WRITE(planner.retract_acceleration);
|
EEPROM_WRITE(planner.retract_acceleration);
|
||||||
EEPROM_WRITE(planner.travel_acceleration);
|
EEPROM_WRITE(planner.travel_acceleration);
|
||||||
@ -387,6 +402,7 @@ void Config_Postprocess() {
|
|||||||
// SERIAL_CHAR(']');
|
// SERIAL_CHAR(']');
|
||||||
// SERIAL_EOL;
|
// SERIAL_EOL;
|
||||||
|
|
||||||
|
// Version has to match or defaults are used
|
||||||
if (strncmp(version, stored_ver, 3) != 0) {
|
if (strncmp(version, stored_ver, 3) != 0) {
|
||||||
Config_ResetDefault();
|
Config_ResetDefault();
|
||||||
}
|
}
|
||||||
@ -395,10 +411,24 @@ void Config_Postprocess() {
|
|||||||
|
|
||||||
eeprom_checksum = 0; // clear before reading first "real data"
|
eeprom_checksum = 0; // clear before reading first "real data"
|
||||||
|
|
||||||
// version number match
|
// Number of esteppers may change
|
||||||
EEPROM_READ(planner.axis_steps_per_mm);
|
uint8_t esteppers;
|
||||||
EEPROM_READ(planner.max_feedrate_mm_s);
|
EEPROM_READ(esteppers);
|
||||||
EEPROM_READ(planner.max_acceleration_mm_per_s2);
|
|
||||||
|
// Get only the number of E stepper parameters previously stored
|
||||||
|
// Any steppers added later are set to their defaults
|
||||||
|
const float def1[] = DEFAULT_AXIS_STEPS_PER_UNIT, def2[] = DEFAULT_MAX_FEEDRATE;
|
||||||
|
const long def3[] = DEFAULT_MAX_ACCELERATION;
|
||||||
|
float tmp1[XYZ + esteppers], tmp2[XYZ + esteppers];
|
||||||
|
long tmp3[XYZ + esteppers];
|
||||||
|
EEPROM_READ(tmp1);
|
||||||
|
EEPROM_READ(tmp2);
|
||||||
|
EEPROM_READ(tmp3);
|
||||||
|
LOOP_XYZE_N(i) {
|
||||||
|
planner.axis_steps_per_mm[i] = i < XYZ + esteppers ? tmp1[i] : def1[i < COUNT(def1) ? i : COUNT(def1) - 1];
|
||||||
|
planner.max_feedrate_mm_s[i] = i < XYZ + esteppers ? tmp2[i] : def2[i < COUNT(def2) ? i : COUNT(def2) - 1];
|
||||||
|
planner.max_acceleration_mm_per_s2[i] = i < XYZ + esteppers ? tmp3[i] : def3[i < COUNT(def3) ? i : COUNT(def3) - 1];
|
||||||
|
}
|
||||||
|
|
||||||
EEPROM_READ(planner.acceleration);
|
EEPROM_READ(planner.acceleration);
|
||||||
EEPROM_READ(planner.retract_acceleration);
|
EEPROM_READ(planner.retract_acceleration);
|
||||||
|
Loading…
Reference in New Issue
Block a user