pins add old names

fix typo

re-write PWM section, add "not on Re-ARM" list
This commit is contained in:
Bob-the-Kuhn 2017-11-07 23:37:57 -06:00
parent 1c6e83c137
commit 8875885a15

View File

@ -34,6 +34,8 @@
* *
*/ */
// numbers in parenthesis () are the mega2560 equivalent pin numbers
#ifndef TARGET_LPC1768 #ifndef TARGET_LPC1768
#error "Oops! Make sure you have LPC1768 selected." #error "Oops! Make sure you have LPC1768 selected."
#endif #endif
@ -47,60 +49,60 @@
// //
// Servos // Servos
// //
#define SERVO0_PIN P1_20 #define SERVO0_PIN P1_20 // (11)
#define SERVO1_PIN P1_21 // also on J5-1 #define SERVO1_PIN P1_21 // ( 6) also on J5-1
#define SERVO2_PIN P1_19 #define SERVO2_PIN P1_19 // ( 5)
#define SERVO3_PIN P1_18 // 5V output - PWM capable #define SERVO3_PIN P1_18 // ( 4) 5V output
// //
// Limit Switches // Limit Switches
// //
#define X_MIN_PIN P1_24 //10k pullup to 3.3V, 1K series #define X_MIN_PIN P1_24 // ( 3) 10k pullup to 3.3V, 1K series
#define X_MAX_PIN P1_25 //10k pullup to 3.3V, 1K series #define X_MAX_PIN P1_25 // ( 2) 10k pullup to 3.3V, 1K series
#define Y_MIN_PIN P1_26 //10k pullup to 3.3V, 1K series #define Y_MIN_PIN P1_26 // (14) 10k pullup to 3.3V, 1K series
#define Y_MAX_PIN P1_27 //10k pullup to 3.3V, 1K series #define Y_MAX_PIN P1_27 // (15) 10k pullup to 3.3V, 1K series
#define Z_MIN_PIN P1_29 //10k pullup to 3.3V, 1K series #define Z_MIN_PIN P1_29 // (18) 10k pullup to 3.3V, 1K series
#define Z_MAX_PIN P1_28 //10k pullup to 3.3V, 1K series #define Z_MAX_PIN P1_28 // (19) 10k pullup to 3.3V, 1K series
// //
// Steppers // Steppers
// //
#define X_STEP_PIN P2_1 #define X_STEP_PIN P2_1 // (54)
#define X_DIR_PIN P0_11 #define X_DIR_PIN P0_11 // (55)
#define X_ENABLE_PIN P0_10 #define X_ENABLE_PIN P0_10 // (38)
#define Y_STEP_PIN P2_2 #define Y_STEP_PIN P2_2 // (60)
#define Y_DIR_PIN P0_20 #define Y_DIR_PIN P0_20 // (61)
#define Y_ENABLE_PIN P0_19 #define Y_ENABLE_PIN P0_19 // (56)
#define Z_STEP_PIN P2_3 #define Z_STEP_PIN P2_3 // (46)
#define Z_DIR_PIN P0_22 #define Z_DIR_PIN P0_22 // (48)
#define Z_ENABLE_PIN P0_21 #define Z_ENABLE_PIN P0_21 // (62)
#define E0_STEP_PIN P2_0 #define E0_STEP_PIN P2_0 // (26)
#define E0_DIR_PIN P0_5 #define E0_DIR_PIN P0_5 // (28)
#define E0_ENABLE_PIN P0_4 #define E0_ENABLE_PIN P0_4 // (24)
#define E1_STEP_PIN P2_8 #define E1_STEP_PIN P2_8 // (36)
#define E1_DIR_PIN P2_13 #define E1_DIR_PIN P2_13 // (34)
#define E1_ENABLE_PIN P4_29 #define E1_ENABLE_PIN P4_29 // (30)
#define E2_STEP_PIN P2_8 #define E2_STEP_PIN P2_8 // (36)
#define E2_DIR_PIN P2_13 #define E2_DIR_PIN P2_13 // (34)
#define E2_ENABLE_PIN P4_29 #define E2_ENABLE_PIN P4_29 // (30)
// //
// Temperature Sensors // Temperature Sensors
// 3.3V max when defined as an analog input // 3.3V max when defined as an analog input
// //
#define TEMP_0_PIN 0 //A0 (T0) - D67 - TEMP_0_PIN #define TEMP_0_PIN 0 //A0 (T0) - (67) - TEMP_0_PIN
#define TEMP_BED_PIN 1 //A1 (T1) - D68 - TEMP_BED_PIN #define TEMP_BED_PIN 1 //A1 (T1) - (68) - TEMP_BED_PIN
#define TEMP_1_PIN 2 //A2 (T2) - D69 - TEMP_1_PIN #define TEMP_1_PIN 2 //A2 (T2) - (69) - TEMP_1_PIN
#define TEMP_2_PIN 3 //A3 - D63 - J5-3 & AUX-2 #define TEMP_2_PIN 3 //A3 - (63) - J5-3 & AUX-2
#define TEMP_3_PIN 4 //A4 - D37 - BUZZER_PIN #define TEMP_3_PIN 4 //A4 - (37) - BUZZER_PIN
//#define TEMP_4_PIN 5 //A5 - D49 - SD_DETECT_PIN //#define TEMP_4_PIN 5 //A5 - (49) - SD_DETECT_PIN
//#define ?? 6 //A6 - D0 - RXD0 - J4-4 & AUX-1 //#define ?? 6 //A6 - ( 0) - RXD0 - J4-4 & AUX-1
#define FILWIDTH_PIN 7 //A7 - D1 - TXD0 - J4-5 & AUX-1 #define FILWIDTH_PIN 7 //A7 - ( 1) - TXD0 - J4-5 & AUX-1
// //
@ -127,13 +129,13 @@
#define MOSFET_D_PIN -1 #define MOSFET_D_PIN -1
#endif #endif
#ifndef RAMPS_D8_PIN #ifndef RAMPS_D8_PIN
#define RAMPS_D8_PIN P2_7 #define RAMPS_D8_PIN P2_7 // (8)
#endif #endif
#ifndef RAMPS_D9_PIN #ifndef RAMPS_D9_PIN
#define RAMPS_D9_PIN P2_4 #define RAMPS_D9_PIN P2_4 // (9)
#endif #endif
#ifndef RAMPS_D10_PIN #ifndef RAMPS_D10_PIN
#define RAMPS_D10_PIN P2_5 #define RAMPS_D10_PIN P2_5 // (10)
#endif #endif
#define HEATER_0_PIN RAMPS_D10_PIN #define HEATER_0_PIN RAMPS_D10_PIN
@ -163,22 +165,22 @@
#endif #endif
#ifndef FAN_PIN #ifndef FAN_PIN
#define FAN_PIN P1_18 // IO pin. Buffer needed #define FAN_PIN P1_18 // (4) IO pin. Buffer needed
#endif #endif
// //
// Misc. Functions // Misc. Functions
// //
#define LED_PIN P4_28 #define LED_PIN P4_28 // (13)
// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector // define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector
#define FIL_RUNOUT_PIN P1_18 #define FIL_RUNOUT_PIN P1_18 // (4)
#define PS_ON_PIN P2_12 #define PS_ON_PIN P2_12 // (12)
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN) #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
#if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // try to use servo connector #if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // try to use servo connector
#define CASE_LIGHT_PIN P1_18 // MUST BE HARDWARE PWM #define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM
#endif #endif
#endif #endif
@ -190,17 +192,17 @@
#undef SERVO1 #undef SERVO1
#undef SERVO2 #undef SERVO2
#undef SERVO3 #undef SERVO3
#define SPINDLE_LASER_ENABLE_PIN P1_21 // Pin should have a pullup/pulldown! #define SPINDLE_LASER_ENABLE_PIN P1_21 // (6) Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN P1_18 // MUST BE HARDWARE PWM #define SPINDLE_LASER_PWM_PIN P1_18 // (4) MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN P1_19 #define SPINDLE_DIR_PIN P1_19 // (5)
#endif #endif
#endif #endif
// //
// Průša i3 MK2 Multiplexer Support // Průša i3 MK2 Multiplexer Support
// //
#define E_MUX0_PIN P0_3 // Z_CS_PIN #define E_MUX0_PIN P0_3 // ( 0) Z_CS_PIN
#define E_MUX1_PIN P0_2 // E0_CS_PIN #define E_MUX1_PIN P0_2 // ( 1) E0_CS_PIN
#define E_MUX2_PIN P0_26 // E1_CS_PIN #define E_MUX2_PIN P0_26 // (63) E1_CS_PIN
/** /**
* LCD / Controller * LCD / Controller
@ -223,76 +225,76 @@
#if ENABLED(ULTRA_LCD) #if ENABLED(ULTRA_LCD)
#define BEEPER_PIN P1_30 // not 5V tolerant #define BEEPER_PIN P1_30 // (37) not 5V tolerant
#define BTN_EN1 P3_26 // J3-2 & AUX-4 #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
#define BTN_EN2 P3_25 // J3-4 & AUX-4 #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // J3-3 & AUX-4 #define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // not 5V tolerant J3-1 & AUX-3 #define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3
#define KILL_PIN P1_22 // J5-4 & AUX-4 #define KILL_PIN P1_22 // (41) J5-4 & AUX-4
#define LCD_PINS_RS P0_16 // J3-7 & AUX-4 #define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4
#define LCD_SDSS P0_16 // J3-7 & AUX-4 #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4
#define LCD_BACKLIGHT_PIN P0_16 // J3-7 & AUX-4 - only used on DOGLCD controllers #define LCD_BACKLIGHT_PIN P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers
#define LCD_PINS_ENABLE P0_18 // (MOSI) J3-10 & AUX-3 #define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3
#define LCD_PINS_D4 P0_15 // (SCK) J3-9 & AUX-3 #define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3
#define DOGLCD_A0 P2_6 // J3-8 & AUX-2 #define DOGLCD_A0 P2_6 // (59) J3-8 & AUX-2
#define DOGLCD_CS P0_26 // J5-3 & AUX-2 #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
#ifdef ULTIPANEL #ifdef ULTIPANEL
#define LCD_PINS_D5 P1_17 // ENET_MDIO #define LCD_PINS_D5 P1_17 // (71) ENET_MDIO
#define LCD_PINS_D6 P1_14 // ENET_RX_ER #define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER
#define LCD_PINS_D7 P1_10 // ENET_RXD1 #define LCD_PINS_D7 P1_10 // (75) ENET_RXD1
#endif #endif
#if ENABLED(NEWPANEL) #if ENABLED(NEWPANEL)
#if ENABLED(REPRAPWORLD_KEYPAD) #if ENABLED(REPRAPWORLD_KEYPAD)
#define SHIFT_OUT P0_18 // (MOSI) J3-10 & AUX-3 #define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3
#define SHIFT_CLK P0_15 // (SCK) J3-9 & AUX-3 #define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3
#define SHIFT_LD P1_31 // not 5V tolerant J3-1 & AUX-3 #define SHIFT_LD P1_31 // (49) not 5V tolerant J3-1 & AUX-3
#endif #endif
#else #else
//#define SHIFT_CLK P3_26 // J3-2 & AUX-4 //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
//#define SHIFT_LD P3_25 // J3-4 & AUX-4 //#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4
//#define SHIFT_OUT P2_11 // J3-3 & AUX-4 //#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4
//#define SHIFT_EN P1_22 // J5-4 & AUX-4 //#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4
#endif #endif
#if ENABLED(VIKI2) || ENABLED(miniVIKI) #if ENABLED(VIKI2) || ENABLED(miniVIKI)
// #define LCD_SCREEN_ROT_180 // #define LCD_SCREEN_ROT_180
#undef BEEPER_PIN #undef BEEPER_PIN
#define BEEPER_PIN P1_30 // may change if cable changes #define BEEPER_PIN P1_30 // (37) may change if cable changes
#define BTN_EN1 P3_26 // J3-2 & AUX-4 #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
#define BTN_EN2 P3_25 // J3-4 & AUX-4 #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // J3-3 & AUX-4 #define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // not 5V tolerant J3-1 & AUX-3 #define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3
#define KILL_PIN P1_22 // J5-4 & AUX-4 #define KILL_PIN P1_22 // (41) J5-4 & AUX-4
#undef DOGLCD_CS #undef DOGLCD_CS
#define DOGLCD_CS P0_16 #define DOGLCD_CS P0_16 // (16)
#undef LCD_BACKLIGHT_PIN //P0_16 // J3-7 & AUX-4 - only used on DOGLCD controllers #undef LCD_BACKLIGHT_PIN //P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers
#undef LCD_PINS_ENABLE //P0_18 // (MOSI) J3-10 & AUX-3 #undef LCD_PINS_ENABLE //P0_18 // (51) (MOSI) J3-10 & AUX-3
#undef LCD_PINS_D4 //P0_15 // (SCK) J3-9 & AUX-3 #undef LCD_PINS_D4 //P0_15 // (52) (SCK) J3-9 & AUX-3
#undef LCD_PINS_D5 //P2_6 // J3-8 & AUX-2 #undef LCD_PINS_D5 //P2_6 // (59) J3-8 & AUX-2
#define DOGLCD_A0 P2_6 // J3-8 & AUX-2 #define DOGLCD_A0 P2_6 // (59) J3-8 & AUX-2
#undef LCD_PINS_D6 //P0_26 // J5-3 & AUX-2 #undef LCD_PINS_D6 //P0_26 // (63) J5-3 & AUX-2
#undef LCD_PINS_D7 //P1_21 // (SERVO1) J5-1 & SERVO connector #undef LCD_PINS_D7 //P1_21 // ( 6) (SERVO1) J5-1 & SERVO connector
#define DOGLCD_SCK SCK_PIN #define DOGLCD_SCK SCK_PIN
#define DOGLCD_MOSI MOSI_PIN #define DOGLCD_MOSI MOSI_PIN
#define STAT_LED_BLUE_PIN P0_26 // may change if cable changes #define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes
#define STAT_LED_RED_PIN P1_21 // may change if cable changes #define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes
#endif #endif
//#define MISO_PIN P0_17 // system defined J3-10 & AUX-3 //#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
//#define MOSI_PIN P0_18 // system defined J3-10 & AUX-3 //#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
//#define SCK_PIN P0_15 // system defined J3-9 & AUX-3 //#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
//#define SS_PIN P1_23 // system defined J3-5 & AUX-3 - sometimes called SDSS //#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 - sometimes called SDSS
#if ENABLED(MINIPANEL) #if ENABLED(MINIPANEL)
// GLCD features // GLCD features
@ -309,44 +311,70 @@
// Ethernet pins // Ethernet pins
// //
#ifndef ULTIPANEL #ifndef ULTIPANEL
#define ENET_MDIO P1_17 // J12-4 #define ENET_MDIO P1_17 // (71) J12-4
#define ENET_RX_ER P1_14 // J12-6 #define ENET_RX_ER P1_14 // (73) J12-6
#define ENET_RXD1 P1_10 // J12-8 #define ENET_RXD1 P1_10 // (75) J12-8
#endif #endif
#define ENET_MOC P1_16 // J12-3 #define ENET_MOC P1_16 // (70) J12-3
#define REF_CLK P1_15 // J12-5 #define REF_CLK P1_15 // (72) J12-5
#define ENET_RXD0 P1_9 // J12-7 #define ENET_RXD0 P1_9 // (74) J12-7
#define ENET_CRS P1_8 // J12-9 #define ENET_CRS P1_8 // (76) J12-9
#define ENET_TX_EN P1_4 // J12-10 #define ENET_TX_EN P1_4 // (77) J12-10
#define ENET_TXD0 P1_0 // J12-11 #define ENET_TXD0 P1_0 // (78) J12-11
#define ENET_TXD1 P1_1 // J12-12 #define ENET_TXD1 P1_1 // (79) J12-12
/** /**
* PWMS * Fast PWMS
* *
* There are 6 PWMS. Each PWM can be assigned to one of two pins. * The LPC1768's hardware PWM controller has 6 channels. Each channel
* can be setup to either control a dedicated pin directly or to generate
* an interrupt. The direct method's duty cycle is accurate to within a
* a microsecond. The interrupt method's average duty cycle has the
* the same accuracy but the individual cycles can vary because of higher
* priority interrupts.
* *
* SERVO2 does NOT have a PWM assigned to it. * All Fast PWMs have a 50Hz rate.
* *
* PWM1.1 P0_18 SERVO3_PIN FIL_RUNOUT_PIN 5V output, PWM * The following pins/signals use the direct method. All other pins use the
* PWM1.1 P2_0 E0_STEP_PIN * the interrupt method. Note that SERVO2_PIN and RAMPS_D8_PIN use the
* PWM1.2 P1_20 SERVO0_PIN * interrupt method.
* PWM1.2 P2_1 X_STEP_PIN * P1_20 (11) SERVO0_PIN
* PWM1.3 P1_21 SERVO1_PIN J5-1 * P1_21 ( 6) SERVO1_PIN J5-1
* PWM1.3 P2_2 Y_STEP_PIN * P0_18 ( 4) SERVO3_PIN 5V output
* PWM1.4 P1_23 SDSS(SSEL0) J3-5 AUX-3 * *P2_4 ( 9) RAMPS_D9_PIN
* PWM1.4 P2_3 Z_STEP_PIN * *P2_5 (10) RAMPS_D10_PIN
* PWM1.5 P1_24 X_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES *
* PWM1.5 P2_4 RAMPS_D9_PIN * * - If used as a heater driver then a Fast PWM is NOT assigned. If used as
* PWM1.6 P1_26 Y_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES * a fan driver then enabling FAST_PWM_FAN assigns a Fast PWM to it.
* PWM1.6 P2_5 RAMPS_D10_PIN
*/ */
/** /**
* special pins * special pins
* P1_30 - not 5V tolerant * P1_30 (37) - not 5V tolerant
* P1_31 - not 5V tolerant * P1_31 (49) - not 5V tolerant
* P0_27 - open collector * P0_27 (57) - open collector
* P0_28 - open collector * P0_28 (58) - open collector
* *
*/ */
/**
* The following mega2560 pins are NOT available in a Re-ARM system
* 7
* 17
* 22
* 23
* 25
* 27
* 29
* 32
* 39
* 40
* 42
* 43
* 44
* 45
* 47
* 64
* 65
* 66
*/