diff --git a/Marlin/example_configurations/Cartesio/Configuration_adv.h b/Marlin/example_configurations/Cartesio/Configuration_adv.h index 687dade67..eecbb25d2 100644 --- a/Marlin/example_configurations/Cartesio/Configuration_adv.h +++ b/Marlin/example_configurations/Cartesio/Configuration_adv.h @@ -695,33 +695,42 @@ #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -// Add support for experimental filament exchange support M600; requires display -#if ENABLED(ULTIPANEL) - // #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too) - #if ENABLED(FILAMENT_CHANGE_FEATURE) - #define FILAMENT_CHANGE_X_POS 30 // X position of hotend - #define FILAMENT_CHANGE_Y_POS 10 // Y position of hotend - #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift) - #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) - #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) - #define FILAMENT_CHANGE_RETRACT_LENGTH 1 // Initial retract in mm - // It is a short retract used immediately after print interrupt before move to filament exchange position - #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s - //#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm - // Longer length for bowden printers to unload filament from whole bowden tube, - // shorter lenght for printers without bowden to unload filament from extruder only, - // 0 to disable unloading for manual unloading - #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast - #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm - // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, - // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast - #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, - // 0 to disable for manual extrusion - // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, - // or until outcoming filament color is not clear for filament color change - #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate - #endif +/** + * Filament Change + * Experimental filament change support. + * Adds the GCode M600 for initiating filament change. + * + * Requires an LCD display. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define FILAMENT_CHANGE_FEATURE +#if ENABLED(FILAMENT_CHANGE_FEATURE) + #define FILAMENT_CHANGE_X_POS 30 // X position of hotend + #define FILAMENT_CHANGE_Y_POS 10 // Y position of hotend + #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift) + #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) + #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) + #define FILAMENT_CHANGE_RETRACT_LENGTH 1 // Initial retract in mm + // It is a short retract used immediately after print interrupt before move to filament exchange position + #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s + //#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm + // Longer length for bowden printers to unload filament from whole bowden tube, + // shorter lenght for printers without bowden to unload filament from extruder only, + // 0 to disable unloading for manual unloading + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast + #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm + // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, + // Short or zero length for printers without bowden where loading is not used + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, + // 0 to disable for manual extrusion + // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, + // or until outcoming filament color is not clear for filament color change + #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index 141879a94..d3b4aea9c 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -721,12 +721,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index c9cdf560e..b81ccf63b 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -721,12 +721,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h index ceb0dfe37..6c37d27fd 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h @@ -704,12 +704,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index 1a84914b1..340dc9bfb 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -708,33 +708,42 @@ #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -// Add support for experimental filament exchange support M600; requires display -#if ENABLED(ULTIPANEL) - #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too) - #if ENABLED(FILAMENT_CHANGE_FEATURE) - #define FILAMENT_CHANGE_X_POS (X_MAX_POS-3) // X position of hotend - #define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend - #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift) - #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) - #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) - #define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm - // It is a short retract used immediately after print interrupt before move to filament exchange position - #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s - #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm - // Longer length for bowden printers to unload filament from whole bowden tube, - // shorter lenght for printers without bowden to unload filament from extruder only, - // 0 to disable unloading for manual unloading - #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast - #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm - // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, - // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast - #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, - // 0 to disable for manual extrusion - // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, - // or until outcoming filament color is not clear for filament color change - #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate - #endif +/** + * Filament Change + * Experimental filament change support. + * Adds the GCode M600 for initiating filament change. + * + * Requires an LCD display. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define FILAMENT_CHANGE_FEATURE +#if ENABLED(FILAMENT_CHANGE_FEATURE) + #define FILAMENT_CHANGE_X_POS (X_MAX_POS-3) // X position of hotend + #define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend + #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift) + #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) + #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) + #define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm + // It is a short retract used immediately after print interrupt before move to filament exchange position + #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm + // Longer length for bowden printers to unload filament from whole bowden tube, + // shorter lenght for printers without bowden to unload filament from extruder only, + // 0 to disable unloading for manual unloading + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast + #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm + // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, + // Short or zero length for printers without bowden where loading is not used + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, + // 0 to disable for manual extrusion + // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, + // or until outcoming filament color is not clear for filament color change + #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/K8400/Configuration_adv.h b/Marlin/example_configurations/K8400/Configuration_adv.h index 67f0ee668..33961eab5 100644 --- a/Marlin/example_configurations/K8400/Configuration_adv.h +++ b/Marlin/example_configurations/K8400/Configuration_adv.h @@ -695,33 +695,42 @@ #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -// Add support for experimental filament exchange support M600; requires display -#if ENABLED(ULTIPANEL) - #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too) - #if ENABLED(FILAMENT_CHANGE_FEATURE) - #define FILAMENT_CHANGE_X_POS 100 // X position of hotend - #define FILAMENT_CHANGE_Y_POS 100 // Y position of hotend - #define FILAMENT_CHANGE_Z_ADD 20 // Z addition of hotend (lift) - #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) - #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) - #define FILAMENT_CHANGE_RETRACT_LENGTH 5 // Initial retract in mm - // It is a short retract used immediately after print interrupt before move to filament exchange position - #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s - #define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // Unload filament length from hotend in mm - // Longer length for bowden printers to unload filament from whole bowden tube, - // shorter lenght for printers without bowden to unload filament from extruder only, - // 0 to disable unloading for manual unloading - #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast - #define FILAMENT_CHANGE_LOAD_LENGTH 600 // Load filament length over hotend in mm - // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, - // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast - #define FILAMENT_CHANGE_EXTRUDE_LENGTH 100 // Extrude filament length in mm after filament is load over the hotend, - // 0 to disable for manual extrusion - // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, - // or until outcoming filament color is not clear for filament color change - #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate - #endif +/** + * Filament Change + * Experimental filament change support. + * Adds the GCode M600 for initiating filament change. + * + * Requires an LCD display. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define FILAMENT_CHANGE_FEATURE +#if ENABLED(FILAMENT_CHANGE_FEATURE) + #define FILAMENT_CHANGE_X_POS 100 // X position of hotend + #define FILAMENT_CHANGE_Y_POS 100 // Y position of hotend + #define FILAMENT_CHANGE_Z_ADD 20 // Z addition of hotend (lift) + #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) + #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) + #define FILAMENT_CHANGE_RETRACT_LENGTH 5 // Initial retract in mm + // It is a short retract used immediately after print interrupt before move to filament exchange position + #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s + #define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // Unload filament length from hotend in mm + // Longer length for bowden printers to unload filament from whole bowden tube, + // shorter lenght for printers without bowden to unload filament from extruder only, + // 0 to disable unloading for manual unloading + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast + #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm + // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, + // Short or zero length for printers without bowden where loading is not used + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_EXTRUDE_LENGTH 100 // Extrude filament length in mm after filament is load over the hotend, + // 0 to disable for manual extrusion + // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, + // or until outcoming filament color is not clear for filament color change + #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index e501cb328..05830ca66 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -721,12 +721,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index deefbf142..812b72e61 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -721,12 +721,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h index 816a45401..a0db6bf68 100644 --- a/Marlin/example_configurations/TAZ4/Configuration_adv.h +++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h @@ -703,33 +703,42 @@ #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -// Add support for experimental filament exchange support M600; requires display -#if ENABLED(ULTIPANEL) - #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too) - #if ENABLED(FILAMENT_CHANGE_FEATURE) - #define FILAMENT_CHANGE_X_POS 3 // X position of hotend - #define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend - #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift) - #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) - #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) - #define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm - // It is a short retract used immediately after print interrupt before move to filament exchange position - #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s - #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm - // Longer length for bowden printers to unload filament from whole bowden tube, - // shorter lenght for printers without bowden to unload filament from extruder only, - // 0 to disable unloading for manual unloading - #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast - #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm - // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, - // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast - #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, - // 0 to disable for manual extrusion - // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, - // or until outcoming filament color is not clear for filament color change - #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate - #endif +/** + * Filament Change + * Experimental filament change support. + * Adds the GCode M600 for initiating filament change. + * + * Requires an LCD display. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define FILAMENT_CHANGE_FEATURE +#if ENABLED(FILAMENT_CHANGE_FEATURE) + #define FILAMENT_CHANGE_X_POS 3 // X position of hotend + #define FILAMENT_CHANGE_Y_POS 3 // Y position of hotend + #define FILAMENT_CHANGE_Z_ADD 10 // Z addition of hotend (lift) + #define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) + #define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers) + #define FILAMENT_CHANGE_RETRACT_LENGTH 2 // Initial retract in mm + // It is a short retract used immediately after print interrupt before move to filament exchange position + #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm + // Longer length for bowden printers to unload filament from whole bowden tube, + // shorter lenght for printers without bowden to unload filament from extruder only, + // 0 to disable unloading for manual unloading + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast + #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm + // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, + // Short or zero length for printers without bowden where loading is not used + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, + // 0 to disable for manual extrusion + // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, + // or until outcoming filament color is not clear for filament color change + #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index c9cdf560e..b81ccf63b 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -721,12 +721,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index 668028969..ce06388eb 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -723,12 +723,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index 668028969..ce06388eb 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -723,12 +723,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h index 7553e02fa..7837c48e3 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h @@ -728,12 +728,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h index 4ce2bd808..4741dd13e 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h @@ -723,12 +723,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index 34cc51e9e..26f68db5d 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -721,12 +721,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\ diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index 8f9df52d3..70a6a76bc 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -721,12 +721,16 @@ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend, // Short or zero length for printers without bowden where loading is not used - #define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast + #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is load over the hotend, // 0 to disable for manual extrusion // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend, // or until outcoming filament color is not clear for filament color change #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate + #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L // Turn off nozzle if user doesn't change filament within this time limit in seconds + #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5L // Number of alert beeps before printer goes quiet + #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change + // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME. #endif /******************************************************************************\