CMS/Marlin
3
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Clean up spacing and comments

Browse Source 
Also clean up some trailing spaces in a few other sources
This commit is contained in:
Scott Lahteine 2015-06-12 04:12:55 -07:00 committed by Richard Wackerbarth
parent d3bce05d54
commit a274769f4f
18 changed files with 82 additions and 92 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

8
Marlin/Configuration.h
View File

@ -235,7 +235,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -406,7 +406,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================
@ -498,7 +498,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. // #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
//Useful to retract a deployable probe. //Useful to retract a deployable probe.
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@ -573,7 +573,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)

4
Marlin/configurator/config/Configuration.h
View File

@ -235,7 +235,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -404,7 +404,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

4
Marlin/example_configurations/Felix/Configuration.h
View File

@ -214,7 +214,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
#define PIDTEMPBED #define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -355,7 +355,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

4
Marlin/example_configurations/Felix/Configuration_DUAL.h
View File

@ -214,7 +214,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
#define PIDTEMPBED #define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -353,7 +353,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

4
Marlin/example_configurations/Hephestos/Configuration.h
View File

@ -231,7 +231,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -379,7 +379,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

4
Marlin/example_configurations/K8200/Configuration.h
View File

@ -245,7 +245,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -422,7 +422,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

4
Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
View File

@ -235,7 +235,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -406,7 +406,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

4
Marlin/example_configurations/SCARA/Configuration.h
View File

@ -260,7 +260,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
#define PIDTEMPBED #define PIDTEMPBED
//
#define BED_LIMIT_SWITCHING #define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -414,7 +414,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

4
Marlin/example_configurations/WITBOX/Configuration.h
View File

@ -230,7 +230,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -378,7 +378,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

27
Marlin/example_configurations/delta/biv2.5/Configuration.h
View File

@ -261,7 +261,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -385,6 +385,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define INVERT_Z_DIR false #define INVERT_Z_DIR false
// @section extruder // @section extruder
// For direct drive extruder v9 set to true, for geared extruder set to false.
#define INVERT_E0_DIR false #define INVERT_E0_DIR false
#define INVERT_E1_DIR false #define INVERT_E1_DIR false
#define INVERT_E2_DIR false #define INVERT_E2_DIR false
@ -430,7 +432,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// #define MESH_BED_LEVELING // Enable mesh bed leveling // #define MESH_BED_LEVELING // Enable mesh bed leveling
#ifdef MANUAL_BED_LEVELING #ifdef MANUAL_BED_LEVELING
#define MBL_Z_STEP 0.025 #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
#endif // MANUAL_BED_LEVELING #endif // MANUAL_BED_LEVELING
#ifdef MESH_BED_LEVELING #ifdef MESH_BED_LEVELING
@ -471,13 +473,13 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#ifdef AUTO_BED_LEVELING_GRID #ifdef AUTO_BED_LEVELING_GRID
// set the rectangle in which to probe
#define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10) #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
#define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
#define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
// Non-linear bed leveling will be used. // Non-linear bed leveling will be used.
@ -516,13 +518,14 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. // #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
//Useful to retract a deployable probe. //Useful to retract a deployable probe.
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
//#define Z_PROBE_ALLEN_KEY //#define Z_PROBE_ALLEN_KEY
#ifdef Z_PROBE_ALLEN_KEY #ifdef Z_PROBE_ALLEN_KEY
#define Z_PROBE_ALLEN_KEY_DEPLOY_X 30 #define Z_PROBE_ALLEN_KEY_DEPLOY_X 30
#define Z_PROBE_ALLEN_KEY_DEPLOY_Y DELTA_PRINTABLE_RADIUS #define Z_PROBE_ALLEN_KEY_DEPLOY_Y DELTA_PRINTABLE_RADIUS
@ -533,7 +536,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define Z_PROBE_ALLEN_KEY_STOW_Z 23 #define Z_PROBE_ALLEN_KEY_STOW_Z 23
#define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20 #define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20
#endif #endif
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it. //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile. // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
@ -595,7 +598,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
* MOVEMENT SETTINGS * MOVEMENT SETTINGS
*/ */
// delta homing speeds must be the same on xyz // delta homing speeds must be the same on xyz
#define HOMING_FEEDRATE {200*30, 200*30, 200*30, 0} // set the homing speeds (mm/min) #define HOMING_FEEDRATE {200*30, 200*30, 200*30, 0} // set the homing speeds (mm/min)
@ -606,7 +608,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
@ -649,7 +651,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#ifdef EEPROM_SETTINGS #ifdef EEPROM_SETTINGS
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
#define EEPROM_CHITCHAT // please keep turned on if you can. #define EEPROM_CHITCHAT // Please keep turned on if you can.
#endif #endif
// @section temperature // @section temperature
@ -667,7 +669,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// @section lcd // @section lcd
// Define your display language below. Replace (en) with your language code and uncomment. // Define your display language below. Replace (en) with your language code and uncomment.
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test // en, pl, fr, de, es, ru, bg, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
// See also language.h // See also language.h
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
@ -690,7 +692,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click //#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms> // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
// http://reprap.org/wiki/PanelOne // http://reprap.org/wiki/PanelOne
//#define PANEL_ONE //#define PANEL_ONE
@ -758,7 +759,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// --------------------- // ---------------------
// 2 wire Non-latching LCD SR from: // 2 wire Non-latching LCD SR from:
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
//#define SAV_3DLCD //#define SAV_3DLCD
// @section extras // @section extras
@ -786,7 +787,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
// #define PHOTOGRAPH_PIN 23 // #define PHOTOGRAPH_PIN 23
// SF send wrong arc g-codes when using Arc Point as fillet procedure // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
//#define SF_ARC_FIX //#define SF_ARC_FIX
// Support for the BariCUDA Paste Extruder. // Support for the BariCUDA Paste Extruder.

31
Marlin/example_configurations/delta/generic/Configuration.h
View File

@ -261,7 +261,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -385,6 +385,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define INVERT_Z_DIR false #define INVERT_Z_DIR false
// @section extruder // @section extruder
// For direct drive extruder v9 set to true, for geared extruder set to false.
#define INVERT_E0_DIR false #define INVERT_E0_DIR false
#define INVERT_E1_DIR false #define INVERT_E1_DIR false
#define INVERT_E2_DIR false #define INVERT_E2_DIR false
@ -423,8 +425,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
@ -433,7 +435,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// #define MESH_BED_LEVELING // Enable mesh bed leveling // #define MESH_BED_LEVELING // Enable mesh bed leveling
#ifdef MANUAL_BED_LEVELING #ifdef MANUAL_BED_LEVELING
#define MBL_Z_STEP 0.025 #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
#endif // MANUAL_BED_LEVELING #endif // MANUAL_BED_LEVELING
#ifdef MESH_BED_LEVELING #ifdef MESH_BED_LEVELING
@ -474,13 +476,13 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#ifdef AUTO_BED_LEVELING_GRID #ifdef AUTO_BED_LEVELING_GRID
// set the rectangle in which to probe
#define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10) #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
#define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
#define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
// Non-linear bed leveling will be used. // Non-linear bed leveling will be used.
@ -519,13 +521,14 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. // #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
//Useful to retract a deployable probe. //Useful to retract a deployable probe.
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
//#define Z_PROBE_ALLEN_KEY //#define Z_PROBE_ALLEN_KEY
#ifdef Z_PROBE_ALLEN_KEY #ifdef Z_PROBE_ALLEN_KEY
#define Z_PROBE_ALLEN_KEY_DEPLOY_X 30 #define Z_PROBE_ALLEN_KEY_DEPLOY_X 30
#define Z_PROBE_ALLEN_KEY_DEPLOY_Y DELTA_PRINTABLE_RADIUS #define Z_PROBE_ALLEN_KEY_DEPLOY_Y DELTA_PRINTABLE_RADIUS
@ -536,7 +539,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define Z_PROBE_ALLEN_KEY_STOW_Z 23 #define Z_PROBE_ALLEN_KEY_STOW_Z 23
#define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20 #define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20
#endif #endif
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it. //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile. // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
@ -598,7 +601,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
* MOVEMENT SETTINGS * MOVEMENT SETTINGS
*/ */
// delta homing speeds must be the same on xyz // delta homing speeds must be the same on xyz
#define HOMING_FEEDRATE {200*60, 200*60, 200*60, 0} // set the homing speeds (mm/min) #define HOMING_FEEDRATE {200*60, 200*60, 200*60, 0} // set the homing speeds (mm/min)
@ -609,7 +611,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
@ -621,7 +623,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
#define DEFAULT_XYJERK 20.0 // (mm/sec) #define DEFAULT_XYJERK 20.0 // (mm/sec)
#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta #define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta
#define DEFAULT_EJERK 5.0 // (mm/sec) #define DEFAULT_EJERK 5.0 // (mm/sec)
//============================================================================= //=============================================================================
@ -652,7 +654,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#ifdef EEPROM_SETTINGS #ifdef EEPROM_SETTINGS
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
#define EEPROM_CHITCHAT // please keep turned on if you can. #define EEPROM_CHITCHAT // Please keep turned on if you can.
#endif #endif
// @section temperature // @section temperature
@ -693,7 +695,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click //#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms> // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
// http://reprap.org/wiki/PanelOne // http://reprap.org/wiki/PanelOne
//#define PANEL_ONE //#define PANEL_ONE
@ -761,7 +762,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// --------------------- // ---------------------
// 2 wire Non-latching LCD SR from: // 2 wire Non-latching LCD SR from:
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
//#define SAV_3DLCD //#define SAV_3DLCD
// @section extras // @section extras
@ -789,7 +790,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
// #define PHOTOGRAPH_PIN 23 // #define PHOTOGRAPH_PIN 23
// SF send wrong arc g-codes when using Arc Point as fillet procedure // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
//#define SF_ARC_FIX //#define SF_ARC_FIX
// Support for the BariCUDA Paste Extruder. // Support for the BariCUDA Paste Extruder.

22
Marlin/example_configurations/delta/kossel_mini/Configuration.h
View File

@ -261,7 +261,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -435,7 +435,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// #define MESH_BED_LEVELING // Enable mesh bed leveling // #define MESH_BED_LEVELING // Enable mesh bed leveling
#ifdef MANUAL_BED_LEVELING #ifdef MANUAL_BED_LEVELING
#define MBL_Z_STEP 0.025 #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
#endif // MANUAL_BED_LEVELING #endif // MANUAL_BED_LEVELING
#ifdef MESH_BED_LEVELING #ifdef MESH_BED_LEVELING
@ -476,8 +476,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#ifdef AUTO_BED_LEVELING_GRID #ifdef AUTO_BED_LEVELING_GRID
// set the rectangle in which to probe
#define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10) #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
#define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
#define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
@ -525,14 +525,12 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
#define Z_PROBE_ALLEN_KEY #define Z_PROBE_ALLEN_KEY
#ifdef Z_PROBE_ALLEN_KEY #ifdef Z_PROBE_ALLEN_KEY
// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
// Kossel Mini // Kossel Mini
#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0
@ -624,7 +622,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
* MOVEMENT SETTINGS * MOVEMENT SETTINGS
*/ */
// delta homing speeds must be the same on xyz // delta homing speeds must be the same on xyz
#define HOMING_FEEDRATE {200*60, 200*60, 200*60, 0} // set the homing speeds (mm/min) #define HOMING_FEEDRATE {200*60, 200*60, 200*60, 0} // set the homing speeds (mm/min)
@ -635,7 +632,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
@ -678,7 +675,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#ifdef EEPROM_SETTINGS #ifdef EEPROM_SETTINGS
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
#define EEPROM_CHITCHAT // please keep turned on if you can. #define EEPROM_CHITCHAT // Please keep turned on if you can.
#endif #endif
// @section temperature // @section temperature
@ -719,7 +716,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click //#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms> // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
// http://reprap.org/wiki/PanelOne // http://reprap.org/wiki/PanelOne
#define PANEL_ONE #define PANEL_ONE
@ -787,7 +783,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// --------------------- // ---------------------
// 2 wire Non-latching LCD SR from: // 2 wire Non-latching LCD SR from:
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
//#define SAV_3DLCD //#define SAV_3DLCD
// @section extras // @section extras
@ -815,7 +811,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
// #define PHOTOGRAPH_PIN 23 // #define PHOTOGRAPH_PIN 23
// SF send wrong arc g-codes when using Arc Point as fillet procedure // SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
//#define SF_ARC_FIX //#define SF_ARC_FIX
// Support for the BariCUDA Paste Extruder. // Support for the BariCUDA Paste Extruder.

36
Marlin/example_configurations/delta/kossel_pro/Configuration.h
View File

@ -204,13 +204,12 @@ Here are some standard links for getting your machine calibrated:
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
// Set/get with gcode: M301 E[extruder number, 0-2] // Set/get with gcode: M301 E[extruder number, 0-2]
#define PID_FUNCTIONAL_RANGE 50 // If the temperature difference between the target temperature and the actual temperature #define PID_FUNCTIONAL_RANGE 50 // If the temperature difference between the target temperature and the actual temperature
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
#define K1 0.95 //smoothing factor within the PID #define K1 0.95 //smoothing factor within the PID
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
// Ultimaker // Ultimaker
// #define DEFAULT_Kp 22.2 // #define DEFAULT_Kp 22.2
// #define DEFAULT_Ki 1.08 // #define DEFAULT_Ki 1.08
@ -245,7 +244,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
#define PIDTEMPBED #define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -306,12 +305,6 @@ Here are some standard links for getting your machine calibrated:
* The solution: Once the temperature reaches the target, start observing. * The solution: Once the temperature reaches the target, start observing.
* If the temperature stays too far below the target (hysteresis) for too long, * If the temperature stays too far below the target (hysteresis) for too long,
* the firmware will halt as a safety precaution. * the firmware will halt as a safety precaution.
*
* Note that because the countdown starts only AFTER the temperature reaches
* the target, this will not catch a thermistor that is already disconnected
* when the print starts!
*
* To enable for all extruder heaters, uncomment the two defines below:
*/ */
#define THERMAL_RUNAWAY_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_RUNAWAY_PROTECTION_HOTENDS // Enable thermal protection for all extruders
@ -342,6 +335,7 @@ Here are some standard links for getting your machine calibrated:
#define DELTA #define DELTA
#ifdef DELTA #ifdef DELTA
// Make delta curves from many straight lines (linear interpolation). // Make delta curves from many straight lines (linear interpolation).
// This is a trade-off between visible corners (not enough segments) // This is a trade-off between visible corners (not enough segments)
// and processor overload (too many expensive sqrt calls). // and processor overload (too many expensive sqrt calls).
@ -494,7 +488,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// @section bedlevel // @section bedlevel
#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) #define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
// /// #define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. // #define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#ifdef ENABLE_AUTO_BED_LEVELING #ifdef ENABLE_AUTO_BED_LEVELING
@ -538,7 +532,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher. // Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher.
#define NONLINEAR_BED_LEVELING #define NONLINEAR_BED_LEVELING
#else // not AUTO_BED_LEVELING_GRID #else // !AUTO_BED_LEVELING_GRID
// Arbitrary points to probe. A simple cross-product // Arbitrary points to probe. A simple cross-product
// is used to estimate the plane of the bed. // is used to estimate the plane of the bed.
@ -574,10 +568,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
#define Z_PROBE_ALLEN_KEY #define Z_PROBE_ALLEN_KEY
@ -586,8 +576,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
//#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30 //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30
//#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS
//#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100 //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100
@ -661,6 +649,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_Z #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_Z
#endif #endif
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
// #define PROBE_SERVO_DEACTIVATION_DELAY 300 // #define PROBE_SERVO_DEACTIVATION_DELAY 300
@ -679,6 +671,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28) #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28)
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28) #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28)
#endif
// Support for a dedicated Z PROBE endstop separate from the Z MIN endstop. // Support for a dedicated Z PROBE endstop separate from the Z MIN endstop.
// If you would like to use both a Z PROBE and a Z MIN endstop together or just a Z PROBE with a custom pin, uncomment #define Z_PROBE_ENDSTOP and read the instructions below. // If you would like to use both a Z PROBE and a Z MIN endstop together or just a Z PROBE with a custom pin, uncomment #define Z_PROBE_ENDSTOP and read the instructions below.
@ -693,7 +686,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// WARNING: Setting the wrong pin may have unexpected and potentially disastrous outcomes. Use with caution and do your homework. // WARNING: Setting the wrong pin may have unexpected and potentially disastrous outcomes. Use with caution and do your homework.
//#define Z_PROBE_ENDSTOP //#define Z_PROBE_ENDSTOP
#endif // Z_SAFE_HOMING
#endif // ENABLE_AUTO_BED_LEVELING #endif // ENABLE_AUTO_BED_LEVELING
@ -720,7 +712,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
////// #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E ////// #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
// set the homing speeds (mm/min) // set the homing speeds (mm/min)
// delta homing speeds must be the same on xyz /// delta homing speeds must be the same on xyz
#define HOMING_FEEDRATE_X (200*60) #define HOMING_FEEDRATE_X (200*60)
#define HOMING_FEEDRATE_Y (200*60) #define HOMING_FEEDRATE_Y (200*60)
#define HOMING_FEEDRATE_Z (200*60) #define HOMING_FEEDRATE_Z (200*60)
@ -799,7 +791,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// @section lcd // @section lcd
// Define your display language below. Replace (en) with your language code and uncomment. // Define your display language below. Replace (en) with your language code and uncomment.
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test // en, pl, fr, de, es, ru, bg, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
// See also language.h // See also language.h
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
@ -1042,7 +1034,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
// Servo Endstops // Servo Endstops
// //
// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. // This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500. // Use M851 to set the z-probe vertical offset from the nozzle. Store that setting with M500.
// //
//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles

4
Marlin/example_configurations/makibox/Configuration.h
View File

@ -224,7 +224,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -376,7 +376,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================

4
Marlin/example_configurations/tvrrug/Round2/Configuration.h
View File

@ -229,7 +229,7 @@ Here are some standard links for getting your machine calibrated:
// shouldn't use bed PID until someone else verifies your hardware works. // shouldn't use bed PID until someone else verifies your hardware works.
// If this is enabled, find your own PID constants below. // If this is enabled, find your own PID constants below.
//#define PIDTEMPBED //#define PIDTEMPBED
//
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
@ -377,7 +377,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
#define FILAMENT_RUNOUT_SCRIPT "M600" #define FILAMENT_RUNOUT_SCRIPT "M600"
#endif #endif
//=========================================================================== //===========================================================================
//=========================== Manual Bed Leveling =========================== //=========================== Manual Bed Leveling ===========================

6
Marlin/temperature.cpp
View File

@ -422,11 +422,11 @@ void checkExtruderAutoFans() {
// update extruder auto fan states // update extruder auto fan states
#if HAS_AUTO_FAN_0 #if HAS_AUTO_FAN_0
setExtruderAutoFanState(EXTRUDER_0_AUTO_FAN_PIN, (fanState & 1) != 0); setExtruderAutoFanState(EXTRUDER_0_AUTO_FAN_PIN, (fanState & 1) != 0);
#endif #endif
#if HAS_AUTO_FAN_1 #if HAS_AUTO_FAN_1
if (EXTRUDER_1_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN) if (EXTRUDER_1_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN)
setExtruderAutoFanState(EXTRUDER_1_AUTO_FAN_PIN, (fanState & 2) != 0); setExtruderAutoFanState(EXTRUDER_1_AUTO_FAN_PIN, (fanState & 2) != 0);
#endif #endif
#if HAS_AUTO_FAN_2 #if HAS_AUTO_FAN_2
if (EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN if (EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN
&& EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN)
@ -1238,7 +1238,7 @@ ISR(TIMER0_COMPB_vect) {
static unsigned char state_timer_heater_ ## n = 0 static unsigned char state_timer_heater_ ## n = 0
#else #else
#define ISR_STATICS(n) static unsigned char soft_pwm_ ## n #define ISR_STATICS(n) static unsigned char soft_pwm_ ## n
#endif #endif
// Statics per heater // Statics per heater
ISR_STATICS(0); ISR_STATICS(0);

2
Marlin/ultralcd.cpp
View File

@ -1665,7 +1665,7 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; }
#define encrot1 2 #define encrot1 2
#define encrot2 3 #define encrot2 3
#define encrot3 1 #define encrot3 1
#endif #endif
/** /**
* Read encoder buttons from the hardware registers * Read encoder buttons from the hardware registers

2
Marlin/ultralcd_implementation_hitachi_HD44780.h
View File

@ -31,7 +31,7 @@
// encoder click is directly connected // encoder click is directly connected
#define BLEN_C 2 #define BLEN_C 2
#define EN_C BIT(BLEN_C) #define EN_C BIT(BLEN_C)
#endif #endif
// //
// Setup other button mappings of each panel // Setup other button mappings of each panel