From b2c1c64fb104906886c17c44fda5e8906b4a9258 Mon Sep 17 00:00:00 2001
From: Dirk Eichel <eichel@bytelink.de>
Date: Fri, 1 Mar 2013 17:39:54 +0100
Subject: [PATCH] Add Motherboard variant 64 - STB V1.1

Definition for the graphic LCD are already in it, they will not harm the
configuration as they are only defined constants
---
 Marlin/Configuration.h | 27 +++++++++++++++++++--------
 1 file changed, 19 insertions(+), 8 deletions(-)

diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 0ba908b06..8031272db 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -34,6 +34,7 @@
 // 6  = Sanguinololu < 1.2
 // 62 = Sanguinololu 1.2 and above
 // 63 = Melzi
+// 64 = STB V1.1
 // 7  = Ultimaker
 // 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
 // 8  = Teensylu
@@ -314,6 +315,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 
 //LCD and SD support
 //#define ULTRA_LCD  //general lcd support, also 16x2
+//#define DOGLCD	// Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
 //#define SDSUPPORT // Enable SD Card Support in Hardware Console
 
 //#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
@@ -322,9 +324,9 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
-
-// The GADGETS3D G3D LCD/SD Controller (blue PCB)
-// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
+
+// The GADGETS3D G3D LCD/SD Controller (blue PCB)
+// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
 //#define G3D_PANEL
 
 //automatic expansion
@@ -347,13 +349,22 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 //  #define NEWPANEL  //enable this if you have a click-encoder panel
   #define SDSUPPORT
   #define ULTRA_LCD
-  #define LCD_WIDTH 20
-  #define LCD_HEIGHT 4
-  
+	#ifdef DOGLCD	// Change number of lines to match the DOG graphic display
+		#define LCD_WIDTH 20
+		#define LCD_HEIGHT 5
+	#else
+		#define LCD_WIDTH 20
+		#define LCD_HEIGHT 4
+	#endif
 #else //no panel but just lcd 
   #ifdef ULTRA_LCD
-    #define LCD_WIDTH 16
-    #define LCD_HEIGHT 2    
+	#ifdef DOGLCD	// Change number of lines to match the 128x64 graphics display
+		#define LCD_WIDTH 20
+		#define LCD_HEIGHT 5
+	#else
+		#define LCD_WIDTH 16
+		#define LCD_HEIGHT 2
+	#endif    
   #endif
 #endif