General cleanup of Re-ARM pins
This commit is contained in:
Scott Lahteine
parent
ee423dcdd0
commit
b738972e69
@ -98,13 +98,6 @@
|
||||
#define E1_CS_PIN -1
|
||||
#endif
|
||||
|
||||
//#define E2_STEP_PIN P2_08 // (36)
|
||||
//#define E2_DIR_PIN P2_13 // (34)
|
||||
//#define E2_ENABLE_PIN P4_29 // (30)
|
||||
//#ifndef E2_CS_PIN
|
||||
// #define E2_CS_PIN -1
|
||||
//#endif
|
||||
|
||||
//
|
||||
// Software SPI pins for TMC2130 stepper drivers
|
||||
//
|
||||
@ -118,14 +111,14 @@
|
||||
// Temperature Sensors
|
||||
// 3.3V max when defined as an analog input
|
||||
//
|
||||
#define TEMP_0_PIN 0 // A0 (T0) - (67) - TEMP_0_PIN
|
||||
#define TEMP_BED_PIN 1 // A1 (T1) - (68) - TEMP_BED_PIN
|
||||
#define TEMP_1_PIN 2 // A2 (T2) - (69) - TEMP_1_PIN
|
||||
#define TEMP_2_PIN 3 // A3 - (63) - J5-3 & AUX-2
|
||||
#define TEMP_3_PIN 4 // A4 - (37) - BUZZER_PIN
|
||||
//#define TEMP_4_PIN 5 // A5 - (49) - SD_DETECT_PIN
|
||||
//#define ?? 6 // A6 - ( 0) - RXD0 - J4-4 & AUX-1
|
||||
#define FILWIDTH_PIN 7 // A7 - ( 1) - TXD0 - J4-5 & AUX-1
|
||||
#define TEMP_0_PIN 0 // A0 (T0) - (67) - TEMP_0_PIN
|
||||
#define TEMP_BED_PIN 1 // A1 (T1) - (68) - TEMP_BED_PIN
|
||||
#define TEMP_1_PIN 2 // A2 (T2) - (69) - TEMP_1_PIN
|
||||
#define TEMP_2_PIN 3 // A3 - (63) - J5-3 & AUX-2
|
||||
#define TEMP_3_PIN 4 // A4 - (37) - BUZZER_PIN
|
||||
//#define TEMP_4_PIN 5 // A5 - (49) - SD_DETECT_PIN
|
||||
//#define ?? 6 // A6 - ( 0) - RXD0 - J4-4 & AUX-1
|
||||
#define FILWIDTH_PIN 7 // A7 - ( 1) - TXD0 - J4-5 & AUX-1
|
||||
|
||||
//
|
||||
// Augmentation for auto-assigning RAMPS plugs
|
||||
@ -195,55 +188,57 @@
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
#define LED_PIN P4_28 // (13)
|
||||
#define LED_PIN P4_28 // (13)
|
||||
|
||||
// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector
|
||||
#ifndef FIL_RUNOUT_PIN
|
||||
#define FIL_RUNOUT_PIN P1_18 // (4)
|
||||
#define FIL_RUNOUT_PIN P1_18 // (4)
|
||||
#endif
|
||||
|
||||
#define PS_ON_PIN P2_12 // (12)
|
||||
#define PS_ON_PIN P2_12 // (12)
|
||||
|
||||
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
|
||||
#if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // try to use servo connector
|
||||
#define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM
|
||||
#if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // Try to use servo connector
|
||||
#define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
// Use servo pins, if available
|
||||
//
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE)
|
||||
#if !defined(NUM_SERVOS) || NUM_SERVOS == 1 // must use servo connector
|
||||
#undef SERVO1
|
||||
#undef SERVO2
|
||||
#undef SERVO3
|
||||
#define SPINDLE_LASER_ENABLE_PIN P1_21 // (6) Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN P1_18 // (4) MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN P1_19 // (5)
|
||||
#if NUM_SERVOS > 1
|
||||
#error "SPINDLE_LASER_ENABLE requires 3 free servo pins."
|
||||
#endif
|
||||
#define SPINDLE_LASER_ENABLE_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN SERVO2_PIN // (5)
|
||||
#endif
|
||||
|
||||
//
|
||||
// Průša i3 MK2 Multiplexer Support
|
||||
//
|
||||
#if SERIAL_PORT != 0 && SERIAL_PORT_2 != 0
|
||||
#define E_MUX0_PIN P0_03 // ( 0) Z_CS_PIN
|
||||
#define E_MUX1_PIN P0_02 // ( 1) E0_CS_PIN
|
||||
#define E_MUX0_PIN P0_03 // ( 0) Z_CS_PIN
|
||||
#define E_MUX1_PIN P0_02 // ( 1) E0_CS_PIN
|
||||
#endif
|
||||
#define E_MUX2_PIN P0_26 // (63) E1_CS_PIN
|
||||
|
||||
/**
|
||||
* LCD / Controller
|
||||
*
|
||||
* All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required.
|
||||
* All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required.
|
||||
*
|
||||
* - https://github.com/wolfmanjm/universal-panel-adapter
|
||||
* - http://panucattdevices.freshdesk.com/support/solutions/articles/1000243195-lcd-display-installation
|
||||
*/
|
||||
|
||||
/**
|
||||
* Smart LCD adapter
|
||||
*
|
||||
* The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
|
||||
* REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
|
||||
* REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
|
||||
* DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
|
||||
* is needed to pick up 5V for the EXP1 connection.
|
||||
*
|
||||
@ -252,95 +247,91 @@
|
||||
* that the garbage/lines are erased immediately after the SD card accesses are completed.
|
||||
*/
|
||||
|
||||
#if ENABLED(ULTRA_LCD)
|
||||
#if ENABLED(CR10_STOCKDISPLAY)
|
||||
|
||||
#if ENABLED(CR10_STOCKDISPLAY)
|
||||
// Re-Arm can support Creality stock display without SD card reader and single cable on EXP3.
|
||||
// Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one
|
||||
// 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3.
|
||||
// Requires REVERSE_ENCODER_DIRECTION in Configuration.h
|
||||
|
||||
// Re-Arm can support Creality stock display without SD card reader and single cable on EXP3.
|
||||
// Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one
|
||||
// 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3.
|
||||
// Requires REVERSE_ENCODER_DIRECTION in Configuration.h
|
||||
#define BEEPER_PIN P2_11 // J3-3 & AUX-4
|
||||
|
||||
#define BEEPER_PIN P2_11 // J3-3 & AUX-4
|
||||
#define BTN_EN1 P0_16 // J3-7 & AUX-4
|
||||
#define BTN_EN2 P1_23 // J3-5 & AUX-4
|
||||
#define BTN_ENC P3_25 // J3-4 & AUX-4
|
||||
|
||||
#define BTN_EN1 P0_16 // J3-7 & AUX-4
|
||||
#define BTN_EN2 P1_23 // J3-5 & AUX-4
|
||||
#define BTN_ENC P3_25 // J3-4 & AUX-4
|
||||
#define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS)
|
||||
#define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI)
|
||||
#define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK)
|
||||
|
||||
#define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS)
|
||||
#define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI)
|
||||
#define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK)
|
||||
#elif ENABLED(ULTRA_LCD)
|
||||
|
||||
#define BEEPER_PIN P1_30 // (37) not 5V tolerant
|
||||
|
||||
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
|
||||
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
|
||||
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
|
||||
|
||||
#define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
|
||||
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4
|
||||
#define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4
|
||||
#define LCD_SDSS P0_16 // (16) J3-7 & AUX-4
|
||||
|
||||
#if ENABLED(NEWPANEL)
|
||||
#if ENABLED(REPRAPWORLD_KEYPAD)
|
||||
#define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3
|
||||
#define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3
|
||||
#define SHIFT_LD P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
|
||||
#endif
|
||||
#else
|
||||
//#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
|
||||
//#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4
|
||||
//#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4
|
||||
//#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4
|
||||
#endif
|
||||
|
||||
#define BEEPER_PIN P1_30 // (37) not 5V tolerant
|
||||
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
|
||||
// #define LCD_SCREEN_ROT_180
|
||||
|
||||
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
|
||||
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
|
||||
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
|
||||
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
|
||||
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
|
||||
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
|
||||
|
||||
#define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3
|
||||
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4
|
||||
#define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4
|
||||
#define LCD_SDSS P0_16 // (16) J3-7 & AUX-4
|
||||
#define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
|
||||
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4
|
||||
|
||||
#if ENABLED(NEWPANEL)
|
||||
#if ENABLED(REPRAPWORLD_KEYPAD)
|
||||
#define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3
|
||||
#define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3
|
||||
#define SHIFT_LD P1_31 // (49) not 5V tolerant J3-1 & AUX-3
|
||||
#endif
|
||||
#else
|
||||
//#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
|
||||
//#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4
|
||||
//#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4
|
||||
//#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4
|
||||
#define DOGLCD_CS P0_16 // (16)
|
||||
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
|
||||
#define DOGLCD_SCK SCK_PIN
|
||||
#define DOGLCD_MOSI MOSI_PIN
|
||||
|
||||
#define STAT_LED_BLUE_PIN P0_26 //(63) may change if cable changes
|
||||
#define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes
|
||||
#else
|
||||
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
|
||||
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
|
||||
#define LCD_BACKLIGHT_PIN P0_16 //(16) J3-7 & AUX-4 - only used on DOGLCD controllers
|
||||
#define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3
|
||||
#define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define LCD_PINS_D5 P1_17 // (71) ENET_MDIO
|
||||
#define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER
|
||||
#define LCD_PINS_D7 P1_10 // (75) ENET_RXD1
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
|
||||
// #define LCD_SCREEN_ROT_180
|
||||
|
||||
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
|
||||
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
|
||||
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
|
||||
|
||||
#define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3
|
||||
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4
|
||||
|
||||
#define DOGLCD_CS P0_16 // (16)
|
||||
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
|
||||
#define DOGLCD_SCK SCK_PIN
|
||||
#define DOGLCD_MOSI MOSI_PIN
|
||||
|
||||
#define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes
|
||||
#define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes
|
||||
#else
|
||||
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
|
||||
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
|
||||
#define LCD_BACKLIGHT_PIN P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers
|
||||
#define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3
|
||||
#define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define LCD_PINS_D5 P1_17 // (71) ENET_MDIO
|
||||
#define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER
|
||||
#define LCD_PINS_D7 P1_10 // (75) ENET_RXD1
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
|
||||
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
|
||||
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
|
||||
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 - sometimes called SDSS
|
||||
|
||||
#if ENABLED(MINIPANEL)
|
||||
// GLCD features
|
||||
//#define LCD_CONTRAST 190
|
||||
// Uncomment screen orientation
|
||||
//#define LCD_SCREEN_ROT_90
|
||||
//#define LCD_SCREEN_ROT_180
|
||||
//#define LCD_SCREEN_ROT_270
|
||||
#endif
|
||||
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
|
||||
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
|
||||
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
|
||||
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS)
|
||||
|
||||
#if ENABLED(MINIPANEL)
|
||||
// GLCD features
|
||||
//#define LCD_CONTRAST 190
|
||||
// Uncomment screen orientation
|
||||
//#define LCD_SCREEN_ROT_90
|
||||
//#define LCD_SCREEN_ROT_180
|
||||
//#define LCD_SCREEN_ROT_270
|
||||
#endif
|
||||
|
||||
#endif // ULTRA_LCD
|
||||
@ -349,17 +340,17 @@
|
||||
// Ethernet pins
|
||||
//
|
||||
#if DISABLED(ULTIPANEL)
|
||||
#define ENET_MDIO P1_17 // (71) J12-4
|
||||
#define ENET_RX_ER P1_14 // (73) J12-6
|
||||
#define ENET_RXD1 P1_10 // (75) J12-8
|
||||
#define ENET_MDIO P1_17 // (71) J12-4
|
||||
#define ENET_RX_ER P1_14 // (73) J12-6
|
||||
#define ENET_RXD1 P1_10 // (75) J12-8
|
||||
#endif
|
||||
#define ENET_MOC P1_16 // (70) J12-3
|
||||
#define REF_CLK P1_15 // (72) J12-5
|
||||
#define ENET_RXD0 P1_09 // (74) J12-7
|
||||
#define ENET_CRS P1_08 // (76) J12-9
|
||||
#define ENET_TX_EN P1_04 // (77) J12-10
|
||||
#define ENET_TXD0 P1_00 // (78) J12-11
|
||||
#define ENET_TXD1 P1_01 // (79) J12-12
|
||||
#define ENET_MOC P1_16 // (70) J12-3
|
||||
#define REF_CLK P1_15 // (72) J12-5
|
||||
#define ENET_RXD0 P1_09 // (74) J12-7
|
||||
#define ENET_CRS P1_08 // (76) J12-9
|
||||
#define ENET_TX_EN P1_04 // (77) J12-10
|
||||
#define ENET_TXD0 P1_00 // (78) J12-11
|
||||
#define ENET_TXD1 P1_01 // (79) J12-12
|
||||
|
||||
//#define USB_SD_DISABLED
|
||||
#define USB_SD_ONBOARD // Provide the onboard SD card to the host as a USB mass storage device
|
||||
@ -369,11 +360,11 @@
|
||||
|
||||
#if ENABLED(LPC_SD_LCD)
|
||||
|
||||
#define SCK_PIN P0_15
|
||||
#define MISO_PIN P0_17
|
||||
#define MOSI_PIN P0_18
|
||||
#define SS_PIN P1_23 // Chip select for SD card used by Marlin
|
||||
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
|
||||
#define SCK_PIN P0_15
|
||||
#define MISO_PIN P0_17
|
||||
#define MOSI_PIN P0_18
|
||||
#define SS_PIN P1_23 // Chip select for SD card used by Marlin
|
||||
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
|
||||
|
||||
#elif ENABLED(LPC_SD_ONBOARD)
|
||||
|
||||
@ -383,66 +374,51 @@
|
||||
#define SHARED_SD_CARD
|
||||
#undef SD_DETECT_PIN // there is also no detect pin for the onboard card
|
||||
#endif
|
||||
#define SCK_PIN P0_07
|
||||
#define MISO_PIN P0_08
|
||||
#define MOSI_PIN P0_09
|
||||
#define SS_PIN P0_06 // Chip select for SD card used by Marlin
|
||||
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
|
||||
|
||||
#define SCK_PIN P0_07
|
||||
#define MISO_PIN P0_08
|
||||
#define MOSI_PIN P0_09
|
||||
#define SS_PIN P0_06 // Chip select for SD card used by Marlin
|
||||
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
|
||||
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Fast PWMs
|
||||
*
|
||||
* The LPC1768's hardware PWM controller has 6 channels. Each channel
|
||||
* The LPC1768's hardware PWM controller has 6 channels. Each channel
|
||||
* can be setup to either control a dedicated pin directly or to generate
|
||||
* an interrupt. The direct method's duty cycle is accurate to within a
|
||||
* a microsecond. The interrupt method's average duty cycle has the
|
||||
* an interrupt. The direct method's duty cycle is accurate to within a
|
||||
* a microsecond. The interrupt method's average duty cycle has the
|
||||
* the same accuracy but the individual cycles can vary because of higher
|
||||
* priority interrupts.
|
||||
*
|
||||
* All Fast PWMs have a 50Hz rate.
|
||||
*
|
||||
* The following pins/signals use the direct method. All other pins use the
|
||||
* The following pins/signals use the direct method. All other pins use the
|
||||
* the interrupt method. Note that SERVO2_PIN and RAMPS_D8_PIN use the
|
||||
* interrupt method.
|
||||
*
|
||||
* P1_20 (11) SERVO0_PIN
|
||||
* P1_21 ( 6) SERVO1_PIN J5-1
|
||||
* P0_18 ( 4) SERVO3_PIN 5V output
|
||||
* *P2_04 ( 9) RAMPS_D9_PIN
|
||||
* *P2_05 (10) RAMPS_D10_PIN
|
||||
*
|
||||
* * - If used as a heater driver then a Fast PWM is NOT assigned. If used as
|
||||
* * - If used as a heater driver then a Fast PWM is NOT assigned. If used as
|
||||
* a fan driver then enabling FAST_PWM_FAN assigns a Fast PWM to it.
|
||||
*/
|
||||
|
||||
/**
|
||||
* Special pins
|
||||
* P1_30 (37) - not 5V tolerant
|
||||
* P1_31 (49) - not 5V tolerant
|
||||
* P0_27 (57) - open collector
|
||||
* P0_28 (58) - open collector
|
||||
*
|
||||
*/
|
||||
* P1_30 (37) (NOT 5V tolerant)
|
||||
* P1_31 (49) (NOT 5V tolerant)
|
||||
* P0_27 (57) (Open collector)
|
||||
* P0_28 (58) (Open collector)
|
||||
*/
|
||||
|
||||
/**
|
||||
* The following mega2560 pins are NOT available in a Re-ARM system
|
||||
* 7
|
||||
* 17
|
||||
* 22
|
||||
* 23
|
||||
* 25
|
||||
* 27
|
||||
* 29
|
||||
* 32
|
||||
* 39
|
||||
* 40
|
||||
* 42
|
||||
* 43
|
||||
* 44
|
||||
* 45
|
||||
* 47
|
||||
* 64
|
||||
* 65
|
||||
* 66
|
||||
* The following mega2560 pins are NOT available in a Re-ARM system:
|
||||
*
|
||||
* 7, 17, 22, 23, 25, 27, 29, 32, 39, 40, 42, 43, 44, 45, 47, 64, 65, 66
|
||||
*/
|
||||
|
||||
Loading…
Reference in New Issue
Block a user