CMS/Marlin
3
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Move BLTouch options to adv config (#14131)

Browse Source 
Plus other BLTouch and menu enhancements.
This commit is contained in:
InsanityAutomation 2019-06-10 18:46:42 -04:00 committed by Scott Lahteine
parent 0ca2073625
commit b7eeb5b13b
180 changed files with 5277 additions and 6291 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

66
Marlin/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
Marlin/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

3
Marlin/src/lcd/language/language_en.h
View File

@ -933,6 +933,9 @@
#ifndef MSG_BLTOUCH_MODE_ECHO
#define MSG_BLTOUCH_MODE_ECHO _UxGT("Report Drain")
#endif
#ifndef MSG_BLTOUCH_MODE_CHANGE
#define MSG_BLTOUCH_MODE_CHANGE _UxGT("DANGER: Bad settings can cause damage! Proceed anyway?")
#endif
#ifndef MSG_MANUAL_DEPLOY
#define MSG_MANUAL_DEPLOY _UxGT("Deploy Z-Probe")
#endif

16
Marlin/src/lcd/menu/menu_configuration.cpp
View File

@ -199,11 +199,19 @@ static void lcd_factory_settings() {
MENU_ITEM(function, MSG_BLTOUCH_STOW, bltouch._stow);
MENU_ITEM(function, MSG_BLTOUCH_SW_MODE, bltouch._set_SW_mode);
#if ENABLED(BLTOUCH_LCD_VOLTAGE_MENU)
MENU_ITEM(function, MSG_BLTOUCH_5V_MODE, bltouch._set_5V_mode);
MENU_ITEM(function, MSG_BLTOUCH_OD_MODE, bltouch._set_OD_mode);
MENU_ITEM(submenu, MSG_BLTOUCH_5V_MODE, []{
do_select_screen(PSTR(MSG_BLTOUCH_5V_MODE), PSTR(MSG_BUTTON_CANCEL), bltouch._set_5V_mode, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
});
MENU_ITEM(submenu, MSG_BLTOUCH_OD_MODE, []{
do_select_screen(PSTR(MSG_BLTOUCH_OD_MODE), PSTR(MSG_BUTTON_CANCEL), bltouch._set_OD_mode, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
});
MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE, bltouch._mode_store);
MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE_5V, bltouch.mode_conv_5V);
MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE_OD, bltouch.mode_conv_OD);
MENU_ITEM(submenu, MSG_BLTOUCH_MODE_STORE_5V, []{
do_select_screen(PSTR(MSG_BLTOUCH_MODE_STORE_5V), PSTR(MSG_BUTTON_CANCEL), bltouch.mode_conv_5V, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
});
MENU_ITEM(submenu, MSG_BLTOUCH_MODE_STORE_OD, []{
do_select_screen(PSTR(MSG_BLTOUCH_MODE_STORE_OD), PSTR(MSG_BUTTON_CANCEL), bltouch.mode_conv_OD, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
});
MENU_ITEM(function, MSG_BLTOUCH_MODE_ECHO, bltouch_report);
#endif
END_MENU();

37
Marlin/src/lcd/ultralcd.cpp
View File

@ -196,10 +196,39 @@ millis_t next_button_update_ms;
#endif
void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte) {
void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte, bool wordwrap/*=false*/) {
SETCURSOR(x, y);
if (string) {
uint8_t *p = (uint8_t*)string;
if (!string) return;
uint8_t *p = (uint8_t*)string;
if (wordwrap) {
uint8_t *wrd = p, c = 0;
for (;;) {
wchar_t ch;
p = get_utf8_value_cb(p, cb_read_byte, &ch);
const bool eol = !ch;
if (eol || ch == ' ' || ch == '-' || ch == '+' || ch == '.') {
if (!c && ch == ' ') continue; // collapse extra spaces
if (x + c > LCD_WIDTH && c < (LCD_WIDTH) * 3 / 4) { // should it wrap?
x = 0; y++; // move x to string len (plus space)
SETCURSOR(0, y); // simulate carriage return
}
c += !eol; // +1 so the space will be printed
x += c; // advance x to new position
while (c--) { // character countdown
wrd = get_utf8_value_cb(wrd, cb_read_byte, &ch); // get characters again
lcd_put_wchar(ch); // word (plus space) to the LCD
}
if (eol) break; // all done
wrd = nullptr; // set up for next word
}
else {
if (!wrd) wrd = p; // starting a new word?
c++; // count word characters
}
}
}
else {
for (;;) {
wchar_t ch;
p = get_utf8_value_cb(p, cb_read_byte, &ch);
@ -221,7 +250,7 @@ millis_t next_button_update_ms;
x = (LCD_WIDTH - plen - slen) / 2;
y = LCD_HEIGHT > 3 ? 1 : 0;
}
wrap_string_P(x, y, pref);
wrap_string_P(x, y, pref, true);
if (string) {
if (x) { x = 0; y++; } // Move to the start of the next line
wrap_string(x, y, string);

6
Marlin/src/lcd/ultralcd.h
View File

@ -74,9 +74,9 @@
#include "fontutils.h"
void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte);
inline void wrap_string_P(uint8_t &x, uint8_t &y, PGM_P const pstr) { _wrap_string(x, y, pstr, read_byte_rom); }
inline void wrap_string(uint8_t &x, uint8_t &y, const char * const string) { _wrap_string(x, y, string, read_byte_ram); }
void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte, const bool wordwrap=false);
inline void wrap_string_P(uint8_t &x, uint8_t &y, PGM_P const pstr, const bool wordwrap=false) { _wrap_string(x, y, pstr, read_byte_rom, wordwrap); }
inline void wrap_string(uint8_t &x, uint8_t &y, const char * const string, const bool wordwrap=false) { _wrap_string(x, y, string, read_byte_ram, wordwrap); }
#if ENABLED(SDSUPPORT)
#include "../sd/cardreader.h"

66
config/default/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/default/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/3DFabXYZ/Migbot/Configuration.h
View File

@ -834,72 +834,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/3DFabXYZ/Migbot/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/AlephObjects/TAZ4/Configuration.h
View File

@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/AlephObjects/TAZ4/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/AliExpress/CL-260/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

66
config/examples/AliExpress/UM2pExt/Configuration.h
View File

@ -839,72 +839,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/AliExpress/UM2pExt/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Anet/A2/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Anet/A2/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Anet/A2plus/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Anet/A2plus/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Anet/A6/Configuration.h
View File

@ -875,72 +875,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Anet/A6/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Anet/A8/Configuration.h
View File

@ -841,72 +841,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Anet/A8/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Anet/A8plus/Configuration.h
View File

@ -839,72 +839,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Anet/A8plus/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Anet/E16/Configuration.h
View File

@ -840,72 +840,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Anet/E16/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/AnyCubic/i3/Configuration.h
View File

@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/AnyCubic/i3/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/ArmEd/Configuration.h
View File

@ -829,72 +829,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/ArmEd/Configuration_adv.h
View File

@ -528,6 +528,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Azteeg/X5GT/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

66
config/examples/BIBO/TouchX/cyclops/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/BIBO/TouchX/default/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/BIBO/TouchX/default/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/BQ/Hephestos/Configuration.h
View File

@ -816,72 +816,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/BQ/Hephestos/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/BQ/Hephestos_2/Configuration.h
View File

@ -829,72 +829,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/BQ/Hephestos_2/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/BQ/WITBOX/Configuration.h
View File

@ -816,72 +816,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/BQ/WITBOX/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Cartesio/Configuration.h
View File

@ -827,72 +827,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Cartesio/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Creality/CR-10/Configuration.h
View File

@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Creality/CR-10/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Creality/CR-10S/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Creality/CR-10S/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Creality/CR-10_5S/Configuration.h
View File

@ -829,72 +829,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Creality/CR-10_5S/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Creality/CR-10mini/Configuration.h
View File

@ -847,72 +847,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Creality/CR-10mini/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Creality/CR-8/Configuration.h
View File

@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Creality/CR-8/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Creality/Ender-2/Configuration.h
View File

@ -832,72 +832,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Creality/Ender-2/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Creality/Ender-3/Configuration.h
View File

@ -832,72 +832,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Creality/Ender-3/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Creality/Ender-4/Configuration.h
View File

@ -838,72 +838,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Creality/Ender-4/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

67
config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
View File

@ -523,6 +523,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Einstart-S/Configuration.h
View File

@ -837,72 +837,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Einstart-S/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Felix/Configuration.h
View File

@ -810,72 +810,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Felix/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Felix/DUAL/Configuration.h
View File

@ -810,72 +810,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

66
config/examples/FlashForge/CreatorPro/Configuration.h
View File

@ -820,72 +820,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/FlashForge/CreatorPro/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/FolgerTech/i3-2020/Configuration.h
View File

@ -834,72 +834,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/FolgerTech/i3-2020/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Formbot/Raptor/Configuration.h
View File

@ -911,72 +911,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Formbot/Raptor/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

67
config/examples/Formbot/T_Rex_2+/Configuration.h
View File

@ -857,73 +857,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Formbot/T_Rex_2+/Configuration_adv.h
View File

@ -528,6 +528,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Formbot/T_Rex_3/Configuration.h
View File

@ -844,72 +844,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Formbot/T_Rex_3/Configuration_adv.h
View File

@ -528,6 +528,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Geeetech/A10M/Configuration.h
View File

@ -811,72 +811,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
#define BLTOUCH_DELAY 200
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Geeetech/A10M/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
#define BLTOUCH_DELAY 200
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Geeetech/A20M/Configuration.h
View File

@ -811,72 +811,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
#define BLTOUCH_DELAY 200
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Geeetech/A20M/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
#define BLTOUCH_DELAY 200
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Geeetech/GT2560/Configuration.h
View File

@ -843,72 +843,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

3
config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
View File

@ -828,9 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
//#define BLTOUCH_DELAY 500 // Minimum Command delay (ms). Enable and increase if needed
#endif
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

66
config/examples/Geeetech/MeCreator2/Configuration.h
View File

@ -835,72 +835,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Geeetech/MeCreator2/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
View File

@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

66
config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
View File

@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

66
config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
View File

@ -828,72 +828,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Infitary/i3-M508/Configuration.h
View File

@ -832,72 +832,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Infitary/i3-M508/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/JGAurora/A5/Configuration.h
View File

@ -840,72 +840,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/JGAurora/A5/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/MakerParts/Configuration.h
View File

@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/MakerParts/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Malyan/M150/Configuration.h
View File

@ -848,72 +848,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Malyan/M150/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

66
config/examples/Malyan/M200/Configuration.h
View File

@ -827,72 +827,6 @@
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE

67
config/examples/Malyan/M200/Configuration_adv.h
View File

@ -524,6 +524,73 @@
// Enable this if X or Y can't home without homing the other axis first.
//#define CODEPENDENT_XY_HOMING
#if ENABLED(BLTOUCH)
/**
* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
* Do not activate settings that the probe might not understand. Clones might misunderstand
* advanced commands.
*
* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
* check the wiring of the BROWN, RED and ORANGE wires.
*
* Note: If the trigger signal of your probe is not being recognized, it has been very often
* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
* like they would be with a real switch. So please check the wiring first.
*
* Settings for all BLTouch and clone probes:
*/
// Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed.
//#define BLTOUCH_DELAY 500
/**
* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
*/
// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
// in special cases, like noisy or filtered input configurations.
//#define BLTOUCH_FORCE_SW_MODE
/**
* Settings for BLTouch Smart 3.0 and 3.1
* Summary:
* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
* - High-Speed mode
* - Disable LCD voltage options
*/
/**
* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
* If disabled, OD mode is the hard-coded default on 3.0
* On startup, Marlin will compare its eeprom to this vale. If the selected mode
* differs, a mode set eeprom write will be completed at initialization.
* Use the option below to force an eeprom write to a V3.1 probe regardless.
*/
//#define BLTOUCH_SET_5V_MODE
/**
* Safety: Activate if connecting a probe with an unknown voltage mode.
* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
* To preserve the life of the probe, use this once then turn it off and re-flash.
*/
//#define BLTOUCH_FORCE_MODE_SET
/**
* Use "HIGH SPEED" mode for probing.
* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
*/
//#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH
/**
* Z Steppers Auto-Alignment
* Add the G34 command to align multiple Z steppers using a bed probe.

Some files were not shown because too many files have changed in this diff Show More