BigTreeTech SKR v1.4 support (#16236)
This commit is contained in:
BigTreeTech
Scott Lahteine
parent
1bad8f1b17
commit
bbe0ffb2fa
@ -188,7 +188,7 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1109)
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),1110)
|
||||
# zrib V2.0 control board (Chinese knock off RAMPS replica)
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),1111)
|
||||
# Bigtreetech or BIQU KFB2.0
|
||||
# BigTreeTech or BIQU KFB2.0
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),1112)
|
||||
# Felix 2.0+ Electronics Board (RAMPS like)
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),1113)
|
||||
|
||||
@ -64,7 +64,7 @@
|
||||
#define BOARD_MKS_BASE_HEROIC 1108 // MKS BASE 1.0 with Heroic HR4982 stepper drivers
|
||||
#define BOARD_MKS_GEN_13 1109 // MKS GEN v1.3 or 1.4
|
||||
#define BOARD_MKS_GEN_L 1110 // MKS GEN L
|
||||
#define BOARD_KFB_2 1111 // Bigtreetech or BIQU KFB2.0
|
||||
#define BOARD_KFB_2 1111 // BigTreeTech or BIQU KFB2.0
|
||||
#define BOARD_ZRIB_V20 1112 // zrib V2.0 control board (Chinese knock off RAMPS replica)
|
||||
#define BOARD_FELIX2 1113 // Felix 2.0+ Electronics Board (RAMPS like)
|
||||
#define BOARD_RIGIDBOARD 1114 // Invent-A-Part RigidBoard
|
||||
@ -208,14 +208,15 @@
|
||||
#define BOARD_COHESION3D_MINI 2011 // Cohesion3D Mini
|
||||
#define BOARD_SMOOTHIEBOARD 2012 // Smoothieboard
|
||||
#define BOARD_AZTEEG_X5_MINI_WIFI 2013 // Azteeg X5 Mini Wifi (Power outputs: Hotend0, Bed, Fan)
|
||||
#define BOARD_BIGTREE_SKR_V1_1 2014 // BIGTREE SKR_V1.1 (Power outputs: Hotend0,Hotend1, Fan, Bed)
|
||||
#define BOARD_BIQU_B300_V1_0 2015 // BIQU B300_V1.0 (Power outputs: Hotend0, Fan, Bed, SPI Driver)
|
||||
#define BOARD_BIGTREE_SKR_V1_3 2016 // BIGTREE SKR_V1.3 (Power outputs: Hotend0, Hotend1, Fan, Bed)
|
||||
#define BOARD_AZTEEG_X5_MINI 2017 // Azteeg X5 Mini (Power outputs: Hotend0, Bed, Fan)
|
||||
#define BOARD_MKS_SGEN 2018 // MKS-SGen (Power outputs: Hotend0, Hotend1, Bed, Fan)
|
||||
#define BOARD_MKS_SGEN_L 2019 // MKS-SGen-L (Power outputs: Hotend0, Hotend1, Bed, Fan)
|
||||
#define BOARD_TH3D_EZBOARD 2020 // TH3D EZBoard v1.0
|
||||
#define BOARD_GMARSH_X6_REV1 2021 // GMARSH X6 board, revision 1 prototype
|
||||
#define BOARD_BIQU_B300_V1_0 2014 // BIQU B300_V1.0 (Power outputs: Hotend0, Fan, Bed, SPI Driver)
|
||||
#define BOARD_AZTEEG_X5_MINI 2015 // Azteeg X5 Mini (Power outputs: Hotend0, Bed, Fan)
|
||||
#define BOARD_MKS_SGEN 2016 // MKS-SGen (Power outputs: Hotend0, Hotend1, Bed, Fan)
|
||||
#define BOARD_MKS_SGEN_L 2017 // MKS-SGen-L (Power outputs: Hotend0, Hotend1, Bed, Fan)
|
||||
#define BOARD_TH3D_EZBOARD 2018 // TH3D EZBoard v1.0
|
||||
#define BOARD_GMARSH_X6_REV1 2019 // GMARSH X6 board, revision 1 prototype
|
||||
#define BOARD_BIGTREE_SKR_V1_1 2020 // BigTreeTech SKR v1.1 (Power outputs: Hotend0, Hotend1, Fan, Bed)
|
||||
#define BOARD_BIGTREE_SKR_V1_3 2021 // BigTreeTech SKR v1.3 (Power outputs: Hotend0, Hotend1, Fan, Bed)
|
||||
#define BOARD_BIGTREE_SKR_V1_4 2022 // BigTreeTech SKR v1.4 (Power outputs: Hotend0, Hotend1, Fan, Bed)
|
||||
|
||||
//
|
||||
// SAM3X8E ARM Cortex M3
|
||||
|
||||
@ -95,7 +95,6 @@ void forward_kinematics_SCARA(const float &a, const float &b) {
|
||||
void inverse_kinematics(const xyz_pos_t &raw) {
|
||||
|
||||
#if ENABLED(MORGAN_SCARA)
|
||||
|
||||
/**
|
||||
* Morgan SCARA Inverse Kinematics. Results in 'delta'.
|
||||
*
|
||||
|
||||
@ -31,18 +31,29 @@
|
||||
//
|
||||
// Steppers
|
||||
//
|
||||
|
||||
#ifndef E1_STEP_PIN
|
||||
#define E1_STEP_PIN P0_01
|
||||
#endif
|
||||
#ifndef E1_DIR_PIN
|
||||
#define E1_DIR_PIN P0_00
|
||||
#endif
|
||||
#ifndef E1_ENABLE_PIN
|
||||
#define E1_ENABLE_PIN P0_10
|
||||
#endif
|
||||
|
||||
//
|
||||
// Temperature Sensors
|
||||
// 3.3V max when defined as an analog input
|
||||
//
|
||||
#define TEMP_BED_PIN P0_23_A0 // A0 (T0) - (67) - TEMP_BED_PIN
|
||||
#ifndef TEMP_0_PIN
|
||||
#define TEMP_0_PIN P0_24_A1 // A1 (T1) - (68) - TEMP_0_PIN
|
||||
#endif
|
||||
#ifndef TEMP_1_PIN
|
||||
#define TEMP_1_PIN P0_25_A2 // A2 (T2) - (69) - TEMP_1_PIN
|
||||
#endif
|
||||
#ifndef TEMP_BED_PIN
|
||||
#define TEMP_BED_PIN P0_23_A0 // A0 (T0) - (67) - TEMP_BED_PIN
|
||||
#endif
|
||||
|
||||
//
|
||||
// Heaters / Fans
|
||||
|
||||
280
Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h
Normal file
280
Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h
Normal file
@ -0,0 +1,280 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
#define BOARD_INFO_NAME "BIGTREE SKR 1.4"
|
||||
|
||||
//
|
||||
// SD Connection
|
||||
//
|
||||
#ifndef SDCARD_CONNECTION
|
||||
#define SDCARD_CONNECTION LCD
|
||||
#endif
|
||||
|
||||
//
|
||||
// Servos
|
||||
//
|
||||
#define SERVO0_PIN P2_00
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#define X_STOP_PIN P1_29
|
||||
#define Y_STOP_PIN P1_28
|
||||
#define Z_STOP_PIN P1_27
|
||||
|
||||
//
|
||||
// Z Probe (when not Z_MIN_PIN)
|
||||
//
|
||||
#ifndef Z_MIN_PROBE_PIN
|
||||
#define Z_MIN_PROBE_PIN P0_10
|
||||
#endif
|
||||
|
||||
//
|
||||
// Filament Runout Sensor
|
||||
//
|
||||
#define FIL_RUNOUT_PIN P1_26
|
||||
#define FIL_RUNOUT2_PIN P1_25
|
||||
|
||||
//
|
||||
// Power Supply Control
|
||||
//
|
||||
#ifndef PS_ON_PIN
|
||||
#define PS_ON_PIN P1_00
|
||||
#endif
|
||||
|
||||
//
|
||||
// Power Loss Detection
|
||||
//
|
||||
#ifndef POWER_LOSS_PIN
|
||||
#define POWER_LOSS_PIN P1_00
|
||||
#endif
|
||||
|
||||
//
|
||||
// Steppers
|
||||
//
|
||||
#define X_STEP_PIN P2_02
|
||||
#define X_DIR_PIN P2_06
|
||||
#define X_ENABLE_PIN P2_01
|
||||
#ifndef X_CS_PIN
|
||||
#define X_CS_PIN P1_10
|
||||
#endif
|
||||
|
||||
#define Y_STEP_PIN P0_19
|
||||
#define Y_DIR_PIN P0_20
|
||||
#define Y_ENABLE_PIN P2_08
|
||||
#ifndef Y_CS_PIN
|
||||
#define Y_CS_PIN P1_09
|
||||
#endif
|
||||
|
||||
#define Z_STEP_PIN P0_22
|
||||
#define Z_DIR_PIN P2_11
|
||||
#define Z_ENABLE_PIN P0_21
|
||||
#ifndef Z_CS_PIN
|
||||
#define Z_CS_PIN P1_08
|
||||
#endif
|
||||
|
||||
#define E0_STEP_PIN P2_13
|
||||
#define E0_DIR_PIN P0_11
|
||||
#define E0_ENABLE_PIN P2_12
|
||||
#ifndef E0_CS_PIN
|
||||
#define E0_CS_PIN P1_04
|
||||
#endif
|
||||
|
||||
#define E1_STEP_PIN P1_15
|
||||
#define E1_DIR_PIN P1_14
|
||||
#define E1_ENABLE_PIN P1_16
|
||||
#ifndef E1_CS_PIN
|
||||
#define E1_CS_PIN P1_01
|
||||
#endif
|
||||
|
||||
#define TEMP_1_PIN P0_23_A0 // A2 (T2) - (69) - TEMP_1_PIN
|
||||
#define TEMP_BED_PIN P0_25_A2 // A0 (T0) - (67) - TEMP_BED_PIN
|
||||
|
||||
//
|
||||
// Include common SKR pins
|
||||
//
|
||||
#include "pins_BTT_SKR.h"
|
||||
|
||||
//
|
||||
// Software SPI pins for TMC2130 stepper drivers
|
||||
//
|
||||
#if ENABLED(TMC_USE_SW_SPI)
|
||||
#ifndef TMC_SW_MOSI
|
||||
#define TMC_SW_MOSI P1_17
|
||||
#endif
|
||||
#ifndef TMC_SW_MISO
|
||||
#define TMC_SW_MISO P0_05
|
||||
#endif
|
||||
#ifndef TMC_SW_SCK
|
||||
#define TMC_SW_SCK P0_04
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if HAS_TMC220x
|
||||
/**
|
||||
* TMC2208/TMC2209 stepper drivers
|
||||
*
|
||||
* Hardware serial communication ports.
|
||||
* If undefined software serial is used according to the pins below
|
||||
*/
|
||||
//#define X_HARDWARE_SERIAL Serial
|
||||
//#define X2_HARDWARE_SERIAL Serial1
|
||||
//#define Y_HARDWARE_SERIAL Serial1
|
||||
//#define Y2_HARDWARE_SERIAL Serial1
|
||||
//#define Z_HARDWARE_SERIAL Serial1
|
||||
//#define Z2_HARDWARE_SERIAL Serial1
|
||||
//#define E0_HARDWARE_SERIAL Serial1
|
||||
//#define E1_HARDWARE_SERIAL Serial1
|
||||
//#define E2_HARDWARE_SERIAL Serial1
|
||||
//#define E3_HARDWARE_SERIAL Serial1
|
||||
//#define E4_HARDWARE_SERIAL Serial1
|
||||
|
||||
//
|
||||
// Software serial
|
||||
//
|
||||
#define X_SERIAL_TX_PIN P1_10
|
||||
#define X_SERIAL_RX_PIN P1_10
|
||||
|
||||
#define Y_SERIAL_TX_PIN P1_09
|
||||
#define Y_SERIAL_RX_PIN P1_09
|
||||
|
||||
#define Z_SERIAL_TX_PIN P1_08
|
||||
#define Z_SERIAL_RX_PIN P1_08
|
||||
|
||||
#define E0_SERIAL_TX_PIN P1_04
|
||||
#define E0_SERIAL_RX_PIN P1_04
|
||||
|
||||
#define E1_SERIAL_TX_PIN P1_01
|
||||
#define E1_SERIAL_RX_PIN P1_01
|
||||
|
||||
#define Z2_SERIAL_TX_PIN P1_01
|
||||
#define Z2_SERIAL_RX_PIN P1_01
|
||||
|
||||
// Reduce baud rate to improve software serial reliability
|
||||
#define TMC_BAUD_RATE 19200
|
||||
#endif
|
||||
|
||||
//
|
||||
// SD Connection
|
||||
//
|
||||
#if SD_CONNECTION_IS(LCD)
|
||||
#define SS_PIN P0_16
|
||||
#endif
|
||||
|
||||
/**
|
||||
* _____ _____
|
||||
* NC | · · | GND 5V | · · | GND
|
||||
* RESET | · · | 1.31(SD_DETECT) (LCD_D7) 1.23 | · · | 1.22 (LCD_D6)
|
||||
* (MOSI)0.18 | · · | 3.25(BTN_EN2) (LCD_D5) 1.21 | · · | 1.20 (LCD_D4)
|
||||
* (SD_SS)0.16 | · · | 3.26(BTN_EN1) (LCD_RS) 1.19 | · · | 1.18 (LCD_EN)
|
||||
* (SCK)0.15 | · · | 0.17(MISO) (BTN_ENC) 0.28 | · · | 1.30 (BEEPER)
|
||||
* ----- -----
|
||||
* EXP2 EXP1
|
||||
*/
|
||||
#if HAS_SPI_LCD
|
||||
#define BTN_ENC P0_28 // (58) open-drain
|
||||
|
||||
#if ENABLED(CR10_STOCKDISPLAY)
|
||||
#define LCD_PINS_RS P1_22
|
||||
|
||||
#define BTN_EN1 P1_18
|
||||
#define BTN_EN2 P1_20
|
||||
|
||||
#define LCD_PINS_ENABLE P1_23
|
||||
#define LCD_PINS_D4 P1_21
|
||||
|
||||
#else
|
||||
#define LCD_PINS_RS P1_19
|
||||
|
||||
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
|
||||
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
|
||||
|
||||
#define LCD_PINS_ENABLE P1_18
|
||||
#define LCD_PINS_D4 P1_20
|
||||
|
||||
#define LCD_SDSS P0_16 // (16) J3-7 & AUX-4
|
||||
#define SD_DETECT_PIN P1_31 // (49) (NOT 5V tolerant)
|
||||
|
||||
#if ENABLED(FYSETC_MINI_12864)
|
||||
#define DOGLCD_CS P1_18
|
||||
#define DOGLCD_A0 P1_19
|
||||
#define DOGLCD_SCK P0_15
|
||||
#define DOGLCD_MOSI P0_18
|
||||
|
||||
#define LCD_BACKLIGHT_PIN -1
|
||||
|
||||
#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
|
||||
// results in LCD soft SPI mode 3, SD soft SPI mode 0
|
||||
|
||||
#define LCD_RESET_PIN P1_20 // Must be high or open for LCD to operate normally.
|
||||
|
||||
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
||||
#ifndef RGB_LED_R_PIN
|
||||
#define RGB_LED_R_PIN P1_21
|
||||
#endif
|
||||
#ifndef RGB_LED_G_PIN
|
||||
#define RGB_LED_G_PIN P1_22
|
||||
#endif
|
||||
#ifndef RGB_LED_B_PIN
|
||||
#define RGB_LED_B_PIN P1_23
|
||||
#endif
|
||||
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
||||
#define NEOPIXEL_PIN P1_21
|
||||
#endif
|
||||
|
||||
#else // !FYSETC_MINI_12864
|
||||
|
||||
#if ENABLED(MKS_MINI_12864)
|
||||
#define DOGLCD_CS P1_21
|
||||
#define DOGLCD_A0 P1_22
|
||||
#define DOGLCD_SCK P0_15
|
||||
#define DOGLCD_MOSI P0_18
|
||||
#define FORCE_SOFT_SPI
|
||||
#endif
|
||||
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define LCD_PINS_D5 P1_21
|
||||
#define LCD_PINS_D6 P1_22
|
||||
#define LCD_PINS_D7 P1_23
|
||||
#endif
|
||||
|
||||
#endif // !FYSETC_MINI_12864
|
||||
|
||||
#endif
|
||||
|
||||
#endif // HAS_SPI_LCD
|
||||
|
||||
//
|
||||
// Neopixel LED
|
||||
//
|
||||
#ifndef NEOPIXEL_PIN
|
||||
#define NEOPIXEL_PIN P1_24
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Special pins
|
||||
* P1_30 (37) (NOT 5V tolerant)
|
||||
* P1_31 (49) (NOT 5V tolerant)
|
||||
* P0_27 (57) (Open collector)
|
||||
* P0_28 (58) (Open collector)
|
||||
*/
|
||||
@ -354,14 +354,16 @@
|
||||
#include "lpc1768/pins_BIQU_BQ111_A4.h" // LPC1768 env:LPC1768
|
||||
#elif MB(SELENA_COMPACT)
|
||||
#include "lpc1768/pins_SELENA_COMPACT.h" // LPC1768 env:LPC1768
|
||||
#elif MB(BIGTREE_SKR_V1_1)
|
||||
#include "lpc1768/pins_BTT_SKR_V1_1.h" // LPC1768 env:LPC1768
|
||||
#elif MB(BIQU_B300_V1_0)
|
||||
#include "lpc1768/pins_BIQU_B300_V1.0.h" // LPC1768 env:LPC1768
|
||||
#elif MB(BIGTREE_SKR_V1_3)
|
||||
#include "lpc1768/pins_BTT_SKR_V1_3.h" // LPC1768 env:LPC1768
|
||||
#elif MB(GMARSH_X6_REV1)
|
||||
#include "lpc1768/pins_GMARSH_X6_REV1.h" // LPC1768 env:LPC1768
|
||||
#elif MB(BIGTREE_SKR_V1_1)
|
||||
#include "lpc1768/pins_BTT_SKR_V1_1.h" // LPC1768 env:LPC1768
|
||||
#elif MB(BIGTREE_SKR_V1_3)
|
||||
#include "lpc1768/pins_BTT_SKR_V1_3.h" // LPC1768 env:LPC1768
|
||||
#elif MB(BIGTREE_SKR_V1_4)
|
||||
#include "lpc1768/pins_BTT_SKR_V1_4.h" // LPC1768 env:LPC1768
|
||||
|
||||
//
|
||||
// LPC1769 ARM Cortex M3
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
#!/usr/bin/env bash
|
||||
#
|
||||
# Build tests for STM32F103RC Bigtreetech (SKR Mini E3)
|
||||
# Build tests for STM32F103RC BigTreeTech (SKR Mini E3)
|
||||
#
|
||||
|
||||
# exit on first failure
|
||||
@ -13,7 +13,7 @@ restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_MINI_E3_V1_0
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
exec_test $1 $2 "Bigtreetech SKR Mini E3 - Basic Configuration"
|
||||
exec_test $1 $2 "BigTreeTech SKR Mini E3 - Basic Configuration"
|
||||
|
||||
# clean up
|
||||
restore_configs
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
#!/usr/bin/env bash
|
||||
#
|
||||
# Build tests for STM32F103RC Bigtreetech (SKR Mini v1.1)
|
||||
# Build tests for STM32F103RC BigTreeTech (SKR Mini v1.1)
|
||||
#
|
||||
|
||||
# exit on first failure
|
||||
@ -13,7 +13,7 @@ restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BIGTREE_SKR_MINI_V1_1
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
exec_test $1 $2 "Bigtreetech SKR Mini v1.1 - Basic Configuration"
|
||||
exec_test $1 $2 "BigTreeTech SKR Mini v1.1 - Basic Configuration"
|
||||
|
||||
# clean up
|
||||
restore_configs
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
#!/usr/bin/env bash
|
||||
#
|
||||
# Build tests for STM32F103RE Bigtreetech (SKR E3 DIP v1.0)
|
||||
# Build tests for STM32F103RE BigTreeTech (SKR E3 DIP v1.0)
|
||||
#
|
||||
|
||||
# exit on first failure
|
||||
@ -13,7 +13,7 @@ restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BIGTREE_SKR_E3_DIP
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
exec_test $1 $2 "Bigtreetech SKR E3 DIP v1.0 - Basic Configuration"
|
||||
exec_test $1 $2 "BigTreeTech SKR E3 DIP v1.0 - Basic Configuration"
|
||||
|
||||
# clean up
|
||||
restore_configs
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
#!/usr/bin/env bash
|
||||
#
|
||||
# Build tests for STM32F103RE Bigtreetech (SKR E3 DIP v1.0)
|
||||
# Build tests for STM32F103RE BigTreeTech (SKR E3 DIP v1.0)
|
||||
#
|
||||
|
||||
# exit on first failure
|
||||
@ -13,7 +13,7 @@ restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BIGTREE_SKR_E3_DIP
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
exec_test $1 $2 "Bigtreetech SKR E3 DIP v1.0 - Basic Configuration"
|
||||
exec_test $1 $2 "BigTreeTech SKR E3 DIP v1.0 - Basic Configuration"
|
||||
|
||||
# clean up
|
||||
restore_configs
|
||||
|
||||
@ -518,10 +518,9 @@
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
//#define DEFAULT_bedKp 10.00
|
||||
//#define DEFAULT_bedKi .023
|
||||
//#define DEFAULT_bedKd 305.4
|
||||
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S60"
|
||||
#endif // PIDTEMPBED
|
||||
|
||||
|
||||
@ -621,7 +621,7 @@ src_filter = ${common.default_src_filter} +<src/HAL/HAL_STM32>
|
||||
monitor_speed = 250000
|
||||
|
||||
#
|
||||
# Bigtreetech SKR Pro (STM32F407ZGT6 ARM Cortex-M4)
|
||||
# BigTreeTech SKR Pro (STM32F407ZGT6 ARM Cortex-M4)
|
||||
#
|
||||
[env:BIGTREE_SKR_PRO]
|
||||
platform = ststm32
|
||||
@ -646,7 +646,7 @@ src_filter = ${common.default_src_filter} +<src/HAL/HAL_STM32>
|
||||
monitor_speed = 250000
|
||||
|
||||
#
|
||||
# Bigtreetech BTT002 (STM32F407VET6 ARM Cortex-M4)
|
||||
# BigTreeTech BTT002 (STM32F407VET6 ARM Cortex-M4)
|
||||
#
|
||||
[env:BIGTREE_BTT002]
|
||||
platform = ststm32@5.6.0
|
||||
|
||||
Loading…
Reference in New Issue
Block a user