Updates to support 5 extruders

Marlin/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/Configuration_adv.h

@@ -808,6 +808,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -849,6 +850,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -890,6 +895,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -975,6 +981,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1026,6 +1033,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/configuration_store.cpp

@@ -144,9 +144,10 @@
  *  568  M906 E1   stepperE1 current                (uint16_t)
  *  570  M906 E2   stepperE2 current                (uint16_t)
  *  572  M906 E3   stepperE3 current                (uint16_t)
+ *  572  M906 E4   stepperE4 current                (uint16_t)
  *
- *  574                                Minimum end-point
+ *  576                                Minimum end-point
- * 1895 (574 + 36 + 9 + 288 + 988)     Maximum end-point
+ * 1897 (576 + 36 + 9 + 288 + 988)     Maximum end-point
  */
 #include "Marlin.h"
 #include "language.h"
@@ -520,7 +521,7 @@ void Config_Postprocess() {
       EEPROM_WRITE(val);
     #else
       val = 0;
-      for (uint8_t q = 0; q < 10; ++q) EEPROM_WRITE(val);
+      for (uint8_t q = 0; q < 11; ++q) EEPROM_WRITE(val);
     #endif
 
     if (!eeprom_write_error) {
@@ -824,8 +825,12 @@ void Config_Postprocess() {
         #if ENABLED(E3_IS_TMC2130)
           stepperE3.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
         #endif
+        EEPROM_READ(val);
+        #if ENABLED(E4_IS_TMC2130)
+          stepperE4.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
+        #endif
       #else
-        for (uint8_t q = 0; q < 10; q++) EEPROM_READ(val);
+        for (uint8_t q = 0; q < 11; q++) EEPROM_READ(val);
       #endif
 
       if (eeprom_checksum == stored_checksum) {

Marlin/example_configurations/Cartesio/Configuration.h

@@ -143,7 +143,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 3
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/Felix/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 2
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/Hephestos/Configuration.h

@@ -145,7 +145,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -142,7 +142,7 @@
 #define MACHINE_UUID "8d083632-40c5-4649-85b8-43d9ae6c5d55" // BQ Hephestos 2 standard config
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@@ -789,6 +789,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -830,6 +831,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -871,6 +876,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -956,6 +962,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1007,6 +1014,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/K8200/Configuration.h

@@ -162,7 +162,7 @@
 #endif
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -818,6 +818,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -859,6 +860,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -900,6 +905,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -985,6 +991,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1036,6 +1043,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/K8400/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/K8400/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/K8400/Dual-head/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 2
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/RigidBot/Configuration.h

@@ -145,7 +145,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1  // Single extruder. Set to 2 for dual extruders
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/SCARA/Configuration.h

@@ -174,7 +174,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/TAZ4/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/TAZ4/Configuration_adv.h

@@ -813,6 +813,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -854,6 +855,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -895,6 +900,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -980,6 +986,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1031,6 +1038,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/TinyBoy2/Configuration.h

@@ -164,7 +164,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical
@@ -988,13 +988,6 @@
 
   //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
 
-  //#define MANUAL_BED_LEVELING  // Add display menu option for bed leveling.
-  #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
-
-  #if ENABLED(MANUAL_BED_LEVELING)
-    #define MBL_Z_STEP 0.025     // Step size while manually probing Z axis.
-  #endif
-
 #endif // BED_LEVELING
 
 /**

Marlin/example_configurations/TinyBoy2/Configuration_adv.h

@@ -789,6 +789,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -830,6 +831,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -871,6 +876,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -956,6 +962,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1007,6 +1014,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/WITBOX/Configuration.h

@@ -145,7 +145,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/delta/generic/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -427,6 +427,24 @@
 /* actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS */
 #define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}  //  AZTEEG_X3_PRO
 
+//===========================================================================
+//============================== Delta Settings =============================
+//===========================================================================
+
+#if ENABLED(DELTA_AUTO_CALIBRATION)
+  /**
+   * Set the height short (H-10) with M665 Hx.xx.
+   * Set the delta_radius offset (R-5, R-10, R+5, R+10) with M665 Rx.xx.
+   * Run G33 Cx V3 with different values (C2, C-2).
+   * Take the average for R_FACTOR and maximum for H_FACTOR.
+   * If R_FACTOR is too low accuracy is reduced. Too high reduces iteration speed.
+   * Run the tests with default values!!!
+   */
+  //#define DELTA_CALIBRATE_EXPERT_MODE
+  //#define H_FACTOR  1.02 //  1.0 < H_FACTOR <  1.11, default  1.00
+  //#define R_FACTOR -3.95 // -6.7 < R_FACTOR < -2.25, default -2.25
+#endif
+
 //===========================================================================
 //=============================Additional Features===========================
 //===========================================================================
@@ -807,6 +825,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -848,6 +867,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -889,6 +912,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -974,6 +998,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1025,6 +1050,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -427,6 +427,24 @@
 /* actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS */
 #define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}  //  AZTEEG_X3_PRO
 
+//===========================================================================
+//============================== Delta Settings =============================
+//===========================================================================
+
+#if ENABLED(DELTA_AUTO_CALIBRATION)
+  /**
+   * Set the height short (H-10) with M665 Hx.xx.
+   * Set the delta_radius offset (R-5, R-10, R+5, R+10) with M665 Rx.xx.
+   * Run G33 Cx V3 with different values (C2, C-2).
+   * Take the average for R_FACTOR and maximum for H_FACTOR.
+   * If R_FACTOR is too low accuracy is reduced. Too high reduces iteration speed.
+   * Run the tests with default values!!!
+   */
+  //#define DELTA_CALIBRATE_EXPERT_MODE
+  //#define H_FACTOR  1.02 //  1.0 < H_FACTOR <  1.11, default  1.00
+  //#define R_FACTOR -3.95 // -6.7 < R_FACTOR < -2.25, default -2.25
+#endif
+
 //===========================================================================
 //=============================Additional Features===========================
 //===========================================================================
@@ -807,6 +825,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -848,6 +867,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -889,6 +912,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -974,6 +998,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1025,6 +1050,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -146,7 +146,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -812,6 +812,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -853,6 +854,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -894,6 +899,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -979,6 +985,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1030,6 +1037,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -807,6 +807,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -848,6 +849,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -889,6 +894,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -974,6 +980,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1025,6 +1032,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/makibox/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -142,7 +142,7 @@
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
 // This defines the number of extruders
-// :[1, 2, 3, 4]
+// :[1, 2, 3, 4, 5]
 #define EXTRUDERS 1
 
 // Enable if your E steppers or extruder gear ratios are not identical

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -805,6 +805,7 @@
   //#define E1_IS_TMC
   //#define E2_IS_TMC
   //#define E3_IS_TMC
+  //#define E4_IS_TMC
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -846,6 +847,10 @@
   #define E3_SENSE_RESISTOR   91
   #define E3_MICROSTEPS       16
 
+  #define E4_MAX_CURRENT    1000
+  #define E4_SENSE_RESISTOR   91
+  #define E4_MICROSTEPS       16
+
 #endif
 
 // @section TMC2130
@@ -887,6 +892,7 @@
   //#define E1_IS_TMC2130
   //#define E2_IS_TMC2130
   //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
 
   /**
    * Stepper driver settings
@@ -972,6 +978,7 @@
   //#define E1_IS_L6470
   //#define E2_IS_L6470
   //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_K_VAL           50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
@@ -1023,6 +1030,11 @@
   #define E3_OVERCURRENT  2000
   #define E3_STALLCURRENT 1500
 
+  #define E4_MICROSTEPS     16
+  #define E4_K_VAL          50
+  #define E4_OVERCURRENT  2000
+  #define E4_STALLCURRENT 1500
+
 #endif
 
 /**

Marlin/language_an.h

@@ -112,6 +112,7 @@
 #define MSG_E2STEPS                         _UxGT("E2 trangos/mm")
 #define MSG_E3STEPS                         _UxGT("E3 trangos/mm")
 #define MSG_E4STEPS                         _UxGT("E4 trangos/mm")
+#define MSG_E5STEPS                         _UxGT("E5 trangos/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatura")
 #define MSG_MOTION                          _UxGT("Movimiento")
 #define MSG_VOLUMETRIC                      _UxGT("Filamento")

Marlin/language_bg.h

@@ -113,6 +113,7 @@
 #define MSG_E2STEPS                         _UxGT("E2 стъпки/mm")
 #define MSG_E3STEPS                         _UxGT("E3 стъпки/mm")
 #define MSG_E4STEPS                         _UxGT("E4 стъпки/mm")
+#define MSG_E5STEPS                         _UxGT("E5 стъпки/mm")
 #define MSG_TEMPERATURE                     _UxGT("Температура")
 #define MSG_MOTION                          _UxGT("Движение")
 #define MSG_VOLUMETRIC                      _UxGT("Нишка")

Marlin/language_ca.h

@@ -117,6 +117,7 @@
 #define MSG_E2STEPS                         _UxGT("E2passos/mm")
 #define MSG_E3STEPS                         _UxGT("E3passos/mm")
 #define MSG_E4STEPS                         _UxGT("E4passos/mm")
+#define MSG_E5STEPS                         _UxGT("E5passos/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatura")
 #define MSG_MOTION                          _UxGT("Moviment")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_cn.h

@@ -105,6 +105,7 @@
 #define MSG_E2STEPS                         "E2steps/mm"
 #define MSG_E3STEPS                         "E3steps/mm"
 #define MSG_E4STEPS                         "E4steps/mm"
+#define MSG_E5STEPS                         "E5steps/mm"
 #define MSG_TEMPERATURE                     "\xc9\xd2"
 #define MSG_MOTION                          "\xdf\xb2"
 #define MSG_VOLUMETRIC                      "Filament"

Marlin/language_cz.h

@@ -116,6 +116,7 @@
 #define MSG_E2STEPS                         _UxGT("E2kroku/mm")
 #define MSG_E3STEPS                         _UxGT("E3kroku/mm")
 #define MSG_E4STEPS                         _UxGT("E4kroku/mm")
+#define MSG_E5STEPS                         _UxGT("E5kroku/mm")
 #define MSG_TEMPERATURE                     _UxGT("Teplota")
 #define MSG_MOTION                          _UxGT("Pohyb")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_da.h

@@ -114,6 +114,7 @@
 #define MSG_E2STEPS                         _UxGT("E2steps/mm")
 #define MSG_E3STEPS                         _UxGT("E3steps/mm")
 #define MSG_E4STEPS                         _UxGT("E4steps/mm")
+#define MSG_E5STEPS                         _UxGT("E5steps/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatur")
 #define MSG_MOTION                          _UxGT("Bevægelse")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_de.h

@@ -118,6 +118,7 @@
 #define MSG_E2STEPS                         _UxGT("E2 Steps/mm")
 #define MSG_E3STEPS                         _UxGT("E3 Steps/mm")
 #define MSG_E4STEPS                         _UxGT("E4 Steps/mm")
+#define MSG_E5STEPS                         _UxGT("E5 Steps/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatur")
 #define MSG_MOTION                          _UxGT("Bewegung")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_el-gr.h

@@ -112,6 +112,7 @@
 #define MSG_E2STEPS                         _UxGT("Bήματα Ε2 ανά μμ")
 #define MSG_E3STEPS                         _UxGT("Bήματα Ε3 ανά μμ")
 #define MSG_E4STEPS                         _UxGT("Bήματα Ε4 ανά μμ")
+#define MSG_E5STEPS                         _UxGT("Bήματα Ε5 ανά μμ")
 #define MSG_TEMPERATURE                     _UxGT("Θερμοκρασία")
 #define MSG_MOTION                          _UxGT("Κίνηση")
 #define MSG_VOLUMETRIC                      _UxGT("Νήμα")

Marlin/language_el.h

@@ -112,6 +112,7 @@
 #define MSG_E2STEPS                         _UxGT("Bήματα Ε2 ανά μμ")
 #define MSG_E3STEPS                         _UxGT("Bήματα Ε3 ανά μμ")
 #define MSG_E4STEPS                         _UxGT("Bήματα Ε4 ανά μμ")
+#define MSG_E5STEPS                         _UxGT("Bήματα Ε5 ανά μμ")
 #define MSG_TEMPERATURE                     _UxGT("Θερμοκρασία")
 #define MSG_MOTION                          _UxGT("Κίνηση")
 #define MSG_VOLUMETRIC                      _UxGT("Νήμα")

Marlin/language_en.h

@@ -291,6 +291,9 @@
 #ifndef MSG_E4STEPS
   #define MSG_E4STEPS                         _UxGT("E4steps/mm")
 #endif
+#ifndef MSG_E5STEPS
+  #define MSG_E5STEPS                         _UxGT("E5steps/mm")
+#endif
 #ifndef MSG_TEMPERATURE
   #define MSG_TEMPERATURE                     _UxGT("Temperature")
 #endif

Marlin/language_es.h

@@ -116,6 +116,7 @@
 #define MSG_E2STEPS                         _UxGT("E2 pasos/mm")
 #define MSG_E3STEPS                         _UxGT("E3 pasos/mm")
 #define MSG_E4STEPS                         _UxGT("E4 pasos/mm")
+#define MSG_E5STEPS                         _UxGT("E5 pasos/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatura")
 #define MSG_MOTION                          _UxGT("Movimiento")
 #define MSG_VOLUMETRIC                      _UxGT("Filamento")

Marlin/language_eu.h

@@ -103,6 +103,7 @@
 #define MSG_E2STEPS                         _UxGT("E2 pausoak/mm")
 #define MSG_E3STEPS                         _UxGT("E3 pausoak/mm")
 #define MSG_E4STEPS                         _UxGT("E4 pausoak/mm")
+#define MSG_E5STEPS                         _UxGT("E5 pausoak/mm")
 #define MSG_TEMPERATURE                     _UxGT("Tenperatura")
 #define MSG_MOTION                          _UxGT("Mugimendua")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_fi.h

@@ -104,6 +104,7 @@
 #define MSG_E2STEPS                         _UxGT("E2steps/mm")
 #define MSG_E3STEPS                         _UxGT("E3steps/mm")
 #define MSG_E4STEPS                         _UxGT("E4steps/mm")
+#define MSG_E5STEPS                         _UxGT("E5steps/mm")
 #define MSG_TEMPERATURE                     _UxGT("Lämpötila")
 #define MSG_MOTION                          _UxGT("Liike")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_fr.h

@@ -117,6 +117,7 @@
 #define MSG_E2STEPS                         _UxGT("E2pas/mm")
 #define MSG_E3STEPS                         _UxGT("E3pas/mm")
 #define MSG_E4STEPS                         _UxGT("E4pas/mm")
+#define MSG_E5STEPS                         _UxGT("E5pas/mm")
 #define MSG_TEMPERATURE                     _UxGT("Tempzrature")
 #define MSG_MOTION                          _UxGT("Mouvement")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_gl.h

@@ -113,6 +113,7 @@
 #define MSG_E2STEPS                         _UxGT("E2pasos/mm")
 #define MSG_E3STEPS                         _UxGT("E3pasos/mm")
 #define MSG_E4STEPS                         _UxGT("E4pasos/mm")
+#define MSG_E5STEPS                         _UxGT("E5pasos/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatura")
 #define MSG_MOTION                          _UxGT("Movemento")
 #define MSG_VOLUMETRIC                      _UxGT("Filamento")

Marlin/language_hr.h

@@ -112,6 +112,7 @@
 #define MSG_E2STEPS                         _UxGT("E2steps/mm")
 #define MSG_E3STEPS                         _UxGT("E3steps/mm")
 #define MSG_E4STEPS                         _UxGT("E4steps/mm")
+#define MSG_E5STEPS                         _UxGT("E5steps/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperature")
 #define MSG_MOTION                          _UxGT("Gibanje")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_it.h

@@ -120,6 +120,7 @@
 #define MSG_E2STEPS                         _UxGT("E2passi/mm")
 #define MSG_E3STEPS                         _UxGT("E3passi/mm")
 #define MSG_E4STEPS                         _UxGT("E4passi/mm")
+#define MSG_E5STEPS                         _UxGT("E5passi/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatura")
 #define MSG_MOTION                          _UxGT("Movimento")
 #define MSG_VOLUMETRIC                      _UxGT("Filamento")

Marlin/language_kana.h

@@ -137,6 +137,7 @@
   #define MSG_E2STEPS                         "E2steps/mm"
   #define MSG_E3STEPS                         "E3steps/mm"
   #define MSG_E4STEPS                         "E4steps/mm"
+  #define MSG_E5STEPS                         "E5steps/mm"
 #else
   #define MSG_XSTEPS                          "Xsteps"
   #define MSG_YSTEPS                          "Ysteps"
@@ -146,6 +147,7 @@
   #define MSG_E2STEPS                         "E2steps"
   #define MSG_E3STEPS                         "E3steps"
   #define MSG_E4STEPS                         "E4steps"
+  #define MSG_E5STEPS                         "E5steps"
 #endif
 #define MSG_TEMPERATURE                     "\xb5\xdd\xc4\xde"                                                 // "ｵﾝﾄﾞ" ("Temperature")
 #define MSG_MOTION                          "\xb3\xba\xde\xb7\xbe\xaf\xc3\xb2"                                 // "ｳｺﾞｷｾｯﾃｲ" ("Motion")

Marlin/language_kana_utf8.h

@@ -122,6 +122,7 @@
 #define MSG_E2STEPS                         _UxGT("E2steps/mm")
 #define MSG_E3STEPS                         _UxGT("E3steps/mm")
 #define MSG_E4STEPS                         _UxGT("E4steps/mm")
+#define MSG_E5STEPS                         _UxGT("E5steps/mm")
 #define MSG_TEMPERATURE                     _UxGT("オンド")                      // "Temperature"
 #define MSG_MOTION                          _UxGT("ウゴキセッテイ")                // "Motion"
 #define MSG_VOLUMETRIC                      _UxGT("フィラメント")                   // "Filament"

Marlin/language_nl.h

@@ -112,6 +112,7 @@
 #define MSG_E2STEPS                         _UxGT("E2steps/mm")
 #define MSG_E3STEPS                         _UxGT("E3steps/mm")
 #define MSG_E4STEPS                         _UxGT("E4steps/mm")
+#define MSG_E5STEPS                         _UxGT("E5steps/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatuur")
 #define MSG_MOTION                          _UxGT("Beweging")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_pl.h

@@ -112,6 +112,7 @@
 #define MSG_E2STEPS                         _UxGT("krokiE2/mm")
 #define MSG_E3STEPS                         _UxGT("krokiE3/mm")
 #define MSG_E4STEPS                         _UxGT("krokiE4/mm")
+#define MSG_E5STEPS                         _UxGT("krokiE5/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatura")
 #define MSG_MOTION                          _UxGT("Ruch")
 #define MSG_VOLUMETRIC                      _UxGT("Filament")

Marlin/language_pt-br.h

@@ -105,6 +105,7 @@
 #define MSG_E2STEPS                         "E2/mm"
 #define MSG_E3STEPS                         "E3/mm"
 #define MSG_E4STEPS                         "E4/mm"
+#define MSG_E5STEPS                         "E5/mm"
 #define MSG_TEMPERATURE                     "Temperatura"
 #define MSG_MOTION                          "Movimento"
 #define MSG_VOLUMETRIC                      "Filamento"

Marlin/language_pt-br_utf8.h

@@ -105,6 +105,7 @@
 #define MSG_E2STEPS                         _UxGT("E2/mm")
 #define MSG_E3STEPS                         _UxGT("E3/mm")
 #define MSG_E4STEPS                         _UxGT("E4/mm")
+#define MSG_E5STEPS                         _UxGT("E5/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatura")
 #define MSG_MOTION                          _UxGT("Movimento")
 #define MSG_VOLUMETRIC                      _UxGT("Filamento")

Marlin/language_pt.h

@@ -109,6 +109,7 @@
 #define MSG_E2STEPS                         "E2 passo/mm"
 #define MSG_E3STEPS                         "E3 passo/mm"
 #define MSG_E4STEPS                         "E4 passo/mm"
+#define MSG_E5STEPS                         "E5 passo/mm"
 #define MSG_TEMPERATURE                     "Temperatura"
 #define MSG_MOTION                          "Movimento"
 #define MSG_VOLUMETRIC                      "Filamento"

Marlin/language_pt_utf8.h

@@ -109,6 +109,7 @@
 #define MSG_E2STEPS                         _UxGT("E2 passo/mm")
 #define MSG_E3STEPS                         _UxGT("E3 passo/mm")
 #define MSG_E4STEPS                         _UxGT("E4 passo/mm")
+#define MSG_E5STEPS                         _UxGT("E5 passo/mm")
 #define MSG_TEMPERATURE                     _UxGT("Temperatura")
 #define MSG_MOTION                          _UxGT("Movimento")
 #define MSG_VOLUMETRIC                      _UxGT("Filamento")

Marlin/language_tr.h

@@ -117,6 +117,7 @@
 #define MSG_E2STEPS                         _UxGT("E2steps/mm")                                         // E2steps/mm
 #define MSG_E3STEPS                         _UxGT("E3steps/mm")                                         // E3steps/mm
 #define MSG_E4STEPS                         _UxGT("E4steps/mm")                                         // E4steps/mm
+#define MSG_E5STEPS                         _UxGT("E5steps/mm")                                         // E4steps/mm
 #define MSG_TEMPERATURE                     _UxGT("Sıcaklık")                                           // Sıcaklık
 #define MSG_MOTION                          _UxGT("Hareket")                                            // Hareket
 #define MSG_VOLUMETRIC                      _UxGT("Filaman")                                            // Filaman

Marlin/language_uk.h

@@ -113,6 +113,7 @@
 #define MSG_E2STEPS                         _UxGT("E2кроків/мм")
 #define MSG_E3STEPS                         _UxGT("E3кроків/мм")
 #define MSG_E4STEPS                         _UxGT("E4кроків/мм")
+#define MSG_E5STEPS                         _UxGT("E5кроків/мм")
 #define MSG_TEMPERATURE                     _UxGT("Температура")
 #define MSG_MOTION                          _UxGT("Рух")
 #define MSG_VOLUMETRIC                      _UxGT("Волокно")

Marlin/pinsDebug_list.h

@@ -212,6 +212,9 @@
 #if PIN_EXISTS(E3_STEP)
   REPORT_NAME_DIGITAL(E3_STEP_PIN, __LINE__ )
 #endif
+#if PIN_EXISTS(E4_AUTO_FAN)
+  REPORT_NAME_DIGITAL(E4_AUTO_FAN_PIN, __LINE__ )
+#endif
 #if PIN_EXISTS(E4_DIR)
   REPORT_NAME_DIGITAL(E4_DIR_PIN, __LINE__ )
 #endif
@@ -434,6 +437,9 @@
 #if PIN_EXISTS(ORIG_E3_AUTO_FAN)
   REPORT_NAME_DIGITAL(ORIG_E3_AUTO_FAN_PIN, __LINE__ )
 #endif
+#if PIN_EXISTS(ORIG_E4_AUTO_FAN)
+  REPORT_NAME_DIGITAL(ORIG_E4_AUTO_FAN_PIN, __LINE__ )
+#endif
 #if PIN_EXISTS(PHOTOGRAPH)
   REPORT_NAME_DIGITAL(PHOTOGRAPH_PIN, __LINE__ )
 #endif

Marlin/stepper.cpp

@@ -931,6 +931,9 @@ void Stepper::init() {
   #if HAS_E3_DIR
     E3_DIR_INIT;
   #endif
+  #if HAS_E4_DIR
+    E4_DIR_INIT;
+  #endif
 
   // Init Enable Pins - steppers default to disabled.
   #if HAS_X_ENABLE
@@ -973,6 +976,10 @@ void Stepper::init() {
     E3_ENABLE_INIT;
     if (!E_ENABLE_ON) E3_ENABLE_WRITE(HIGH);
   #endif
+  #if HAS_E4_ENABLE
+    E4_ENABLE_INIT;
+    if (!E_ENABLE_ON) E4_ENABLE_WRITE(HIGH);
+  #endif
 
   // Init endstops and pullups
   endstops.init();

Marlin/stepper_indirection.cpp

@@ -75,6 +75,9 @@
   #if ENABLED(E3_IS_TMC)
     _TMC_DEFINE(E3);
   #endif
+  #if ENABLED(E4_IS_TMC)
+    _TMC_DEFINE(E4);
+  #endif
 
   #define _TMC_INIT(A) do{ \
     stepper##A.setMicrosteps(A##_MICROSTEPS); \
@@ -112,6 +115,9 @@
     #if ENABLED(E3_IS_TMC)
       _TMC_INIT(E3);
     #endif
+    #if ENABLED(E4_IS_TMC)
+      _TMC_INIT(E4);
+    #endif
   }
 
 #endif // HAVE_TMCDRIVER
@@ -157,6 +163,9 @@
   #if ENABLED(E3_IS_TMC2130)
     _TMC2130_DEFINE(E3);
   #endif
+  #if ENABLED(E4_IS_TMC2130)
+    _TMC2130_DEFINE(E4);
+  #endif
 
   // Use internal reference voltage for current calculations. This is the default.
   // Following values from Trinamic's spreadsheet with values for a NEMA17 (42BYGHW609)
@@ -213,6 +222,9 @@
     #if ENABLED(E3_IS_TMC2130)
       _TMC2130_INIT(E3);
     #endif
+    #if ENABLED(E4_IS_TMC2130)
+      _TMC2130_INIT(E4);
+    #endif
 
     TMC2130_ADV()
   }
@@ -260,6 +272,9 @@
   #if ENABLED(E3_IS_L6470)
     _L6470_DEFINE(E3);
   #endif
+  #if ENABLED(E4_IS_L6470)
+    _L6470_DEFINE(E4);
+  #endif
 
   #define _L6470_INIT(A) do{ \
     stepper##A.init(A##_K_VAL); \
@@ -300,6 +315,9 @@
     #if ENABLED(E3_IS_L6470)
       _L6470_INIT(E3);
     #endif
+    #if ENABLED(E4_IS_L6470)
+      _L6470_INIT(E4);
+    #endif
   }
 
 #endif // HAVE_L6470DRIVER

Marlin/stepper_indirection.h

@@ -381,6 +381,37 @@
 #define E3_STEP_WRITE(STATE) WRITE(E3_STEP_PIN,STATE)
 #define E3_STEP_READ READ(E3_STEP_PIN)
 
+// E4 Stepper
+#if ENABLED(HAVE_L6470DRIVER) && ENABLED(E4_IS_L6470)
+  extern L6470 stepperE4;
+  #define E4_ENABLE_INIT NOOP
+  #define E4_ENABLE_WRITE(STATE) do{ if (STATE) stepperE4.Step_Clock(stepperE4.getStatus() & STATUS_HIZ); else stepperE4.softFree(); }while(0)
+  #define E4_ENABLE_READ (stepperE4.getStatus() & STATUS_HIZ)
+  #define E4_DIR_INIT NOOP
+  #define E4_DIR_WRITE(STATE) stepperE4.Step_Clock(STATE)
+  #define E4_DIR_READ (stepperE4.getStatus() & STATUS_DIR)
+#else
+  #if ENABLED(HAVE_TMCDRIVER) && ENABLED(E4_IS_TMC)
+    extern TMC26XStepper stepperE4;
+    #define E4_ENABLE_INIT NOOP
+    #define E4_ENABLE_WRITE(STATE) stepperE4.setEnabled(STATE)
+    #define E4_ENABLE_READ stepperE4.isEnabled()
+  #else
+    #if ENABLED(HAVE_TMC2130) && ENABLED(E4_IS_TMC2130)
+      extern TMC2130Stepper stepperE4;
+    #endif
+    #define E4_ENABLE_INIT SET_OUTPUT(E4_ENABLE_PIN)
+    #define E4_ENABLE_WRITE(STATE) WRITE(E4_ENABLE_PIN,STATE)
+    #define E4_ENABLE_READ READ(E4_ENABLE_PIN)
+  #endif
+  #define E4_DIR_INIT SET_OUTPUT(E4_DIR_PIN)
+  #define E4_DIR_WRITE(STATE) WRITE(E4_DIR_PIN,STATE)
+  #define E4_DIR_READ READ(E4_DIR_PIN)
+#endif
+#define E4_STEP_INIT SET_OUTPUT(E4_STEP_PIN)
+#define E4_STEP_WRITE(STATE) WRITE(E4_STEP_PIN,STATE)
+#define E4_STEP_READ READ(E4_STEP_PIN)
+
 /**
  * Extruder indirection for the single E axis
  */

Marlin/ultralcd.cpp

@@ -918,39 +918,26 @@ void kill_screen(const char* lcd_msg) {
   /**
    * Watch temperature callbacks
    */
+  #if HAS_TEMP_HOTEND
     #if WATCH_HOTENDS
-    #if HAS_TEMP_HOTEND
+      #define _WATCH_FUNC(N) thermalManager.start_watching_heater(N)
-      void watch_temp_callback_E0() { thermalManager.start_watching_heater(0); }
-      #if HOTENDS > 1
-        void watch_temp_callback_E1() { thermalManager.start_watching_heater(1); }
-        #if HOTENDS > 2
-          void watch_temp_callback_E2() { thermalManager.start_watching_heater(2); }
-          #if HOTENDS > 3
-            void watch_temp_callback_E3() { thermalManager.start_watching_heater(3); }
-            #if HOTENDS > 4
-              void watch_temp_callback_E4() { thermalManager.start_watching_heater(4); }
-            #endif // HOTENDS > 4
-          #endif // HOTENDS > 3
-        #endif // HOTENDS > 2
-      #endif // HOTENDS > 1
-    #endif
     #else
-    #if HAS_TEMP_HOTEND
+      #define _WATCH_FUNC(N) NOOP
-      void watch_temp_callback_E0() {}
+    #endif
+    void watch_temp_callback_E0() { _WATCH_FUNC(0); }
     #if HOTENDS > 1
-        void watch_temp_callback_E1() {}
+      void watch_temp_callback_E1() { _WATCH_FUNC(1); }
       #if HOTENDS > 2
-          void watch_temp_callback_E2() {}
+        void watch_temp_callback_E2() { _WATCH_FUNC(2); }
         #if HOTENDS > 3
-            void watch_temp_callback_E3() {}
+          void watch_temp_callback_E3() { _WATCH_FUNC(3); }
           #if HOTENDS > 4
-              void watch_temp_callback_E4() {}
+            void watch_temp_callback_E4() { _WATCH_FUNC(4); }
           #endif // HOTENDS > 4
         #endif // HOTENDS > 3
       #endif // HOTENDS > 2
     #endif // HOTENDS > 1
-    #endif
+  #endif // HAS_TEMP_HOTEND
-  #endif
 
   #if WATCH_THE_BED
     void watch_temp_callback_bed() { thermalManager.start_watching_bed(); }
@@ -1905,10 +1892,13 @@ void kill_screen(const char* lcd_msg) {
             case 2: pos_label = PSTR(MSG_MOVE_E MSG_MOVE_E3); break;
             #if E_MANUAL > 3
               case 3: pos_label = PSTR(MSG_MOVE_E MSG_MOVE_E4); break;
-            #endif
+              #if E_MANUAL > 4
-          #endif
+                case 4: pos_label = PSTR(MSG_MOVE_E MSG_MOVE_E5); break;
+              #endif // E_MANUAL > 4
+            #endif // E_MANUAL > 3
+          #endif // E_MANUAL > 2
         }
-      #endif
+      #endif // E_MANUAL > 1
       lcd_implementation_drawedit(pos_label, ftostr41sign(current_position[E_AXIS]));
     }
   }
@@ -1921,9 +1911,12 @@ void kill_screen(const char* lcd_msg) {
       void lcd_move_e2() { _lcd_move_e(2); }
       #if E_MANUAL > 3
         void lcd_move_e3() { _lcd_move_e(3); }
-      #endif
+        #if E_MANUAL > 4
-    #endif
+          void lcd_move_e4() { _lcd_move_e(4); }
-  #endif
+        #endif // E_MANUAL > 4
+      #endif // E_MANUAL > 3
+    #endif // E_MANUAL > 2
+  #endif // E_MANUAL > 1
 
   /**
    *
@@ -1970,9 +1963,12 @@ void kill_screen(const char* lcd_msg) {
       void lcd_move_get_e2_amount()   { _lcd_move_distance_menu(E_AXIS, lcd_move_e2); }
       #if E_MANUAL > 3
         void lcd_move_get_e3_amount() { _lcd_move_distance_menu(E_AXIS, lcd_move_e3); }
-      #endif
+        #if E_MANUAL > 4
-    #endif
+          void lcd_move_get_e4_amount() { _lcd_move_distance_menu(E_AXIS, lcd_move_e4); }
-  #endif
+        #endif // E_MANUAL > 4
+      #endif // E_MANUAL > 3
+    #endif // E_MANUAL > 2
+  #endif // E_MANUAL > 1
 
   /**
    *
@@ -2033,9 +2029,12 @@ void kill_screen(const char* lcd_msg) {
         MENU_ITEM(submenu, MSG_MOVE_E MSG_MOVE_E3, lcd_move_get_e2_amount);
         #if E_MANUAL > 3
           MENU_ITEM(submenu, MSG_MOVE_E MSG_MOVE_E4, lcd_move_get_e3_amount);
-        #endif
+          #if E_MANUAL > 4
-      #endif
+            MENU_ITEM(submenu, MSG_MOVE_E MSG_MOVE_E5, lcd_move_get_e4_amount);
-    #endif
+          #endif // E_MANUAL > 4
+        #endif // E_MANUAL > 3
+      #endif // E_MANUAL > 2
+    #endif // E_MANUAL > 1
 
     END_MENU();
   }
@@ -2239,6 +2238,7 @@ void kill_screen(const char* lcd_msg) {
     // PID-P E2, PID-I E2, PID-D E2, PID-C E2, PID Autotune E2
     // PID-P E3, PID-I E3, PID-D E3, PID-C E3, PID Autotune E3
     // PID-P E4, PID-I E4, PID-D E4, PID-C E4, PID Autotune E4
+    // PID-P E5, PID-I E5, PID-D E5, PID-C E5, PID Autotune E5
     //
     #if ENABLED(PIDTEMP)
 
@@ -2350,8 +2350,11 @@ void kill_screen(const char* lcd_msg) {
       void _reset_e2_acceleration_rate() { _reset_e_acceleration_rate(2); }
       #if E_STEPPERS > 3
         void _reset_e3_acceleration_rate() { _reset_e_acceleration_rate(3); }
-      #endif
+        #if E_STEPPERS > 4
-    #endif
+          void _reset_e4_acceleration_rate() { _reset_e_acceleration_rate(4); }
+        #endif // E_STEPPERS > 4
+      #endif // E_STEPPERS > 3
+    #endif // E_STEPPERS > 2
   #endif
 
   void _planner_refresh_positioning() { planner.refresh_positioning(); }
@@ -2368,8 +2371,11 @@ void kill_screen(const char* lcd_msg) {
       void _planner_refresh_e2_positioning() { _reset_e_acceleration_rate(2); }
       #if E_STEPPERS > 3
         void _planner_refresh_e3_positioning() { _reset_e_acceleration_rate(3); }
-      #endif
+        #if E_STEPPERS > 4
-    #endif
+          void _planner_refresh_e4_positioning() { _reset_e_acceleration_rate(4); }
+        #endif // E_STEPPERS > 4
+      #endif // E_STEPPERS > 3
+    #endif // E_STEPPERS > 2
   #endif
 
   /**
@@ -2411,9 +2417,12 @@ void kill_screen(const char* lcd_msg) {
       #if E_STEPPERS > 2
         MENU_ITEM_EDIT(float3, MSG_VMAX MSG_E3, &planner.max_feedrate_mm_s[E_AXIS + 2], 1, 999);
         #if E_STEPPERS > 3
-          MENU_ITEM_EDIT(float3, MSG_VMAX MSG_E3, &planner.max_feedrate_mm_s[E_AXIS + 3], 1, 999);
+          MENU_ITEM_EDIT(float3, MSG_VMAX MSG_E4, &planner.max_feedrate_mm_s[E_AXIS + 3], 1, 999);
-        #endif
+          #if E_STEPPERS > 4
-      #endif
+            MENU_ITEM_EDIT(float3, MSG_VMAX MSG_E5, &planner.max_feedrate_mm_s[E_AXIS + 4], 1, 999);
+          #endif // E_STEPPERS > 4
+        #endif // E_STEPPERS > 3
+      #endif // E_STEPPERS > 2
     #else
       MENU_ITEM_EDIT(float3, MSG_VMAX MSG_E, &planner.max_feedrate_mm_s[E_AXIS], 1, 999);
     #endif
@@ -2436,8 +2445,11 @@ void kill_screen(const char* lcd_msg) {
         MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_E3, &planner.max_acceleration_mm_per_s2[E_AXIS + 2], 100, 99000, _reset_e2_acceleration_rate);
         #if E_STEPPERS > 3
           MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_E4, &planner.max_acceleration_mm_per_s2[E_AXIS + 3], 100, 99000, _reset_e3_acceleration_rate);
-        #endif
+          #if E_STEPPERS > 4
-      #endif
+            MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_E5, &planner.max_acceleration_mm_per_s2[E_AXIS + 4], 100, 99000, _reset_e4_acceleration_rate);
+          #endif // E_STEPPERS > 4
+        #endif // E_STEPPERS > 3
+      #endif // E_STEPPERS > 2
     #else
       MENU_ITEM_EDIT_CALLBACK(long5, MSG_AMAX MSG_E, &planner.max_acceleration_mm_per_s2[E_AXIS], 100, 99000, _reset_acceleration_rates);
     #endif
@@ -2460,8 +2472,11 @@ void kill_screen(const char* lcd_msg) {
         MENU_ITEM_EDIT_CALLBACK(float62, MSG_E3STEPS, &planner.axis_steps_per_mm[E_AXIS + 2], 5, 9999, _planner_refresh_e2_positioning);
         #if E_STEPPERS > 3
           MENU_ITEM_EDIT_CALLBACK(float62, MSG_E4STEPS, &planner.axis_steps_per_mm[E_AXIS + 3], 5, 9999, _planner_refresh_e3_positioning);
-        #endif
+          #if E_STEPPERS > 4
-      #endif
+            MENU_ITEM_EDIT_CALLBACK(float62, MSG_E5STEPS, &planner.axis_steps_per_mm[E_AXIS + 4], 5, 9999, _planner_refresh_e4_positioning);
+          #endif // E_STEPPERS > 4
+        #endif // E_STEPPERS > 3
+      #endif // E_STEPPERS > 2
     #else
       MENU_ITEM_EDIT_CALLBACK(float62, MSG_ESTEPS, &planner.axis_steps_per_mm[E_AXIS], 5, 9999, _planner_refresh_positioning);
     #endif