Initial Configuration.h for Felix 2.0/3.0
This commit is contained in:
chrono
parent
2e172f38bd
commit
c7fb1b70f2
@ -8,7 +8,7 @@
|
||||
//===========================================================================
|
||||
/*
|
||||
Here are some standard links for getting your machine calibrated:
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
@ -59,7 +59,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_ULTIMAKER
|
||||
#define MOTHERBOARD BOARD_FELIX2
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
@ -79,7 +79,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
#define POWER_SUPPLY 1
|
||||
|
||||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
// #define PS_DEFAULT_OFF
|
||||
#define PS_DEFAULT_OFF
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
@ -104,7 +104,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
||||
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
|
||||
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||||
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
|
||||
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
|
||||
// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
||||
//
|
||||
@ -118,16 +118,16 @@ Here are some standard links for getting your machine calibrated:
|
||||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 -1
|
||||
#define TEMP_SENSOR_1 -1
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 1
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
|
||||
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
|
||||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
@ -187,10 +187,10 @@ Here are some standard links for getting your machine calibrated:
|
||||
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
// Ultimaker
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
// Felix 2.0+ electronics with v4 Hotend
|
||||
#define DEFAULT_Kp 12
|
||||
#define DEFAULT_Ki 0.84
|
||||
#define DEFAULT_Kd 85
|
||||
|
||||
// MakerGear
|
||||
// #define DEFAULT_Kp 7.0
|
||||
@ -263,15 +263,15 @@ The issue: If a thermistor come off, it will read a lower temperature than actua
|
||||
The system will turn the heater on forever, burning up the filament and anything
|
||||
else around.
|
||||
|
||||
After the temperature reaches the target for the first time, this feature will
|
||||
start measuring for how long the current temperature stays below the target
|
||||
After the temperature reaches the target for the first time, this feature will
|
||||
start measuring for how long the current temperature stays below the target
|
||||
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
|
||||
|
||||
If it stays longer than _PERIOD, it means the thermistor temperature
|
||||
cannot catch up with the target, so something *may be* wrong. Then, to be on the
|
||||
safe side, the system will he halt.
|
||||
|
||||
Bear in mind the count down will just start AFTER the first time the
|
||||
Bear in mind the count down will just start AFTER the first time the
|
||||
thermistor temperature is over the target, so you will have no problem if
|
||||
your extruder heater takes 2 minutes to hit the target on heating.
|
||||
|
||||
@ -321,13 +321,13 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
||||
#endif
|
||||
|
||||
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
||||
const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
//#define DISABLE_MAX_ENDSTOPS
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
@ -344,7 +344,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||
|
||||
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
@ -361,11 +361,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
||||
// Travel limits after homing (units are in mm)
|
||||
#define X_MAX_POS 205
|
||||
#define X_MAX_POS 245
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MAX_POS 205
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MAX_POS 235
|
||||
#define Z_MIN_POS 0
|
||||
|
||||
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
|
||||
@ -378,7 +378,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
//===========================================================================
|
||||
|
||||
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
|
||||
#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
//#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
@ -487,9 +487,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
|
||||
@ -510,12 +510,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
|
||||
// default settings
|
||||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker
|
||||
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164}
|
||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_ACCELERATION 1750 //1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 5000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
@ -524,8 +525,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 0.4 // (mm/sec)
|
||||
#define DEFAULT_XYJERK 10 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 0.3 //0.4 // (mm/sec)
|
||||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
|
||||
@ -570,7 +571,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
//#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
|
||||
|
||||
//#define ULTRA_LCD //general LCD support, also 16x2
|
||||
@ -636,13 +637,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define ULTRA_LCD //general LCD support, also 16x2
|
||||
#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||||
#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
|
||||
|
||||
#ifdef miniVIKI
|
||||
#define DEFAULT_LCD_CONTRAST 95
|
||||
#else
|
||||
#define DEFAULT_LCD_CONTRAST 40
|
||||
#endif
|
||||
|
||||
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
@ -733,7 +734,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
//#define SAV_3DLCD
|
||||
#ifdef SAV_3DLCD
|
||||
@ -774,7 +775,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#endif
|
||||
|
||||
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
//#define FAST_PWM_FAN
|
||||
#define FAST_PWM_FAN
|
||||
|
||||
// Temperature status LEDs that display the hotend and bet temperature.
|
||||
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
||||
@ -831,9 +832,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
* Support for a filament diameter sensor
|
||||
* Also allows adjustment of diameter at print time (vs at slicing)
|
||||
* Single extruder only at this point (extruder 0)
|
||||
*
|
||||
*
|
||||
* Motherboards
|
||||
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
|
||||
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
|
||||
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
|
||||
* 301 - Rambo - uses Analog input 3
|
||||
* Note may require analog pins to be defined for different motherboards
|
||||
@ -850,7 +851,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
||||
//defines used in the code
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
||||
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
|
||||
//#define FILAMENT_LCD_DISPLAY
|
||||
@ -864,3 +865,4 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#include "thermistortables.h"
|
||||
|
||||
#endif //__CONFIGURATION_H
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user