Merge pull request #1724 from Natealus/Development

Viki 2 Pins from Manual and Azteeg X3 Pro Endstop Reswap

Marlin/pins_AZTEEG_X3.h

@@ -4,13 +4,33 @@
 
 #include "pins_RAMPS_13.h"
 
-#undef FAN_PIN
 #define FAN_PIN            9 // (Sprinter config)
-
-#undef HEATER_1_PIN
 #define HEATER_1_PIN       -1
 
-#ifdef TEMP_STAT_LEDS
+//LCD Pins//
+
+#if defined(VIKI2) || defined(miniVIKI)
+ #define BEEPER 33
+ // Pins for DOGM SPI LCD Support
+ #define DOGLCD_A0  31 
+ #define DOGLCD_CS  32 
+ #define LCD_SCREEN_ROT_180
+ 
+ //The encoder and click button 
+ #define BTN_EN1 22 
+ #define BTN_EN2 7
+ #define BTN_ENC 12  //the click switch
+ 
+ #define SDSS 53
+ #define SDCARDDETECT -1 // Pin 49 if using display sd interface   
+ 
+  #ifdef TEMP_STAT_LEDS
+   #define STAT_LED_RED 64
+   #define STAT_LED_BLUE 63
+  #endif
+#endif
+
+#elif define TEMP_STAT_LEDS
   #define STAT_LED_RED       6
   #define STAT_LED_BLUE     11
 #endif

Marlin/pins_AZTEEG_X3_PRO.h

@@ -16,23 +16,23 @@
 //
 //This section is to swap the MIN and MAX pins because the X3 Pro comes with only
 //MIN endstops soldered onto the board. Delta code wants the homing endstops to be 
-//the MAX so I swapped them here. Comment them out with // if you want them original.
-//Note: I had to solder on the additional MAX Endstop pins to attach a Z-Probe 
-//endstop switch.
+//the MAX so I swapped them here.
 //
-#undef X_MIN_PIN
-#undef X_MAX_PIN
-#undef Y_MIN_PIN
-#undef Y_MAX_PIN
-#undef Z_MIN_PIN
-#undef Z_MAX_PIN
+ #ifdef DELTA
+  #undef X_MIN_PIN
+  #undef X_MAX_PIN
+  #undef Y_MIN_PIN
+  #undef Y_MAX_PIN
+  #undef Z_MIN_PIN
+  #undef Z_MAX_PIN
 
-#define X_MIN_PIN           2
-#define X_MAX_PIN           3
-#define Y_MIN_PIN          15
-#define Y_MAX_PIN          14
-#define Z_MIN_PIN          19
-#define Z_MAX_PIN          18
+  #define X_MIN_PIN           2
+  #define X_MAX_PIN           3
+  #define Y_MIN_PIN          15
+  #define Y_MAX_PIN          14
+  #define Z_MIN_PIN          19
+  #define Z_MAX_PIN          18
+ #endif
 //
 
 #define E2_STEP_PIN        23
@@ -88,3 +88,26 @@
     #endif
   #endif
 #endif
+
+//LCD Pins//
+
+#if defined(VIKI2) || defined(miniVIKI)
+ #define BEEPER 33
+ // Pins for DOGM SPI LCD Support
+ #define DOGLCD_A0  44
+ #define DOGLCD_CS  45
+ #define LCD_SCREEN_ROT_180
+ 
+ //The encoder and click button
+ #define BTN_EN1 22
+ #define BTN_EN2 7
+ #define BTN_ENC 39  //the click switch
+
+ #define SDSS 53
+ #define SDCARDDETECT 49
+ 
+ #define KILL_PIN 31
+ 
+ #define STAT_LED_RED       32
+ #define STAT_LED_BLUE      35
+#endif

Marlin/pins_PRINTRBOARD.h

@@ -59,6 +59,8 @@
 #define TEMP_1_PIN         -1
 #define TEMP_2_PIN         -1
 
+////LCD Pin Setup////
+
 #define SDPOWER            -1
 #define SDSS                8
 #define LED_PIN            -1
@@ -86,3 +88,24 @@
   //not connected to a pin
   #define SDCARDDETECT -1    
 #endif // ULTRA_LCD && NEWPANEL
+
+#if defined(VIKI2) || defined(miniVIKI)
+ #define BEEPER 32 //FastIO
+ // Pins for DOGM SPI LCD Support
+ #define DOGLCD_A0  42 //Non-FastIO
+ #define DOGLCD_CS  43 //Non-FastIO
+ #define LCD_SCREEN_ROT_180
+ 
+ //The encoder and click button (FastIO Pins)
+ #define BTN_EN1 26 
+ #define BTN_EN2 27
+ #define BTN_ENC 47  //the click switch
+
+ #define SDSS 45
+ #define SDCARDDETECT -1 // FastIO (Manual says 72 I'm not certain cause I can't test) 
+
+ #ifdef TEMP_STAT_LEDS
+  #define STAT_LED_RED      12 //Non-FastIO
+  #define STAT_LED_BLUE     10 //Non-FastIO
+ #endif  
+#endif

Marlin/pins_RAMBO.h

@@ -160,6 +160,26 @@
 
 #endif // ULTRA_LCD
 
+#if defined(VIKI2) || defined(miniVIKI)
+ #define BEEPER 44
+ // Pins for DOGM SPI LCD Support
+ #define DOGLCD_A0  70 
+ #define DOGLCD_CS  71 
+ #define LCD_SCREEN_ROT_180
+  
+ //The encoder and click button 
+ #define BTN_EN1 85 
+ #define BTN_EN2 84
+ #define BTN_ENC 83  //the click switch
+
+ #define SDCARDDETECT -1 // Pin 72 if using easy adapter board   
+
+  #ifdef TEMP_STAT_LEDS
+   #define STAT_LED_RED      22
+   #define STAT_LED_BLUE     32 
+  #endif
+#endif // VIKI2/miniVIKI
+
 #ifdef FILAMENT_SENSOR
   //Filip added pin for Filament sensor analog input 
   #define FILWIDTH_PIN        3