faster GLCD (ST7920 SW-SPI) implementation / fixes
- fixed long menu entries (>14 or >18 chars) caused overrun in dogm lcd implementation - fixed pin set problem when in interrupt - much faster ST7920 SW-SPI implementation - increased ST7920 framebuffer size for more speed
This commit is contained in:
Maik Stohn
parent
971ec35135
commit
da05b3ba94
@ -33,11 +33,11 @@
|
||||
#define LCD_CLICKED (buttons&EN_C)
|
||||
#endif
|
||||
|
||||
// CHANGE_DE begin ***
|
||||
#include <U8glib.h> // DE_U8glib
|
||||
#include <U8glib.h>
|
||||
#include "DOGMbitmaps.h"
|
||||
#include "dogm_font_data_marlin.h"
|
||||
#include "ultralcd.h"
|
||||
#include "ultralcd_st7920_u8glib_rrd.h"
|
||||
|
||||
|
||||
/* Russian language not supported yet, needs custom font
|
||||
@ -74,11 +74,10 @@
|
||||
|
||||
#define FONT_STATUSMENU u8g_font_6x9
|
||||
|
||||
|
||||
// LCD selection
|
||||
#ifdef U8GLIB_ST7920
|
||||
// SPI Com: SCK = en = (D4), MOSI = rw = (RS), CS = di = (ENABLE)
|
||||
U8GLIB_ST7920_128X64_1X u8g(LCD_PINS_D4, LCD_PINS_ENABLE, LCD_PINS_RS);
|
||||
//U8GLIB_ST7920_128X64_RRD u8g(0,0,0);
|
||||
U8GLIB_ST7920_128X64_RRD u8g(0);
|
||||
#else
|
||||
U8GLIB_DOGM128 u8g(DOGLCD_CS, DOGLCD_A0); // HW-SPI Com: CS, A0
|
||||
#endif
|
||||
|
||||
131
Marlin/ultralcd_st7920_u8glib_rrd.h
Normal file
131
Marlin/ultralcd_st7920_u8glib_rrd.h
Normal file
@ -0,0 +1,131 @@
|
||||
#ifndef ULCDST7920_H
|
||||
#define ULCDST7920_H
|
||||
|
||||
#include "Marlin.h"
|
||||
|
||||
#ifdef U8GLIB_ST7920
|
||||
|
||||
//set optimization so ARDUINO optimizes this file
|
||||
#pragma GCC optimize (3)
|
||||
|
||||
#define ST7920_CLK_PIN LCD_PINS_D4
|
||||
#define ST7920_DAT_PIN LCD_PINS_ENABLE
|
||||
#define ST7920_CS_PIN LCD_PINS_RS
|
||||
|
||||
//#define PAGE_HEIGHT 8 //128 byte frambuffer
|
||||
//#define PAGE_HEIGHT 16 //256 byte frambuffer
|
||||
#define PAGE_HEIGHT 32 //512 byte framebuffer
|
||||
|
||||
#define WIDTH 128
|
||||
#define HEIGHT 64
|
||||
|
||||
#include <U8glib.h>
|
||||
|
||||
static void ST7920_SWSPI_SND_8BIT(uint8_t val)
|
||||
{
|
||||
uint8_t i;
|
||||
for( i=0; i<8; i++ )
|
||||
{
|
||||
WRITE(ST7920_CLK_PIN,0);
|
||||
WRITE(ST7920_DAT_PIN,val&0x80);
|
||||
val<<=1;
|
||||
WRITE(ST7920_CLK_PIN,1);
|
||||
}
|
||||
}
|
||||
|
||||
#define ST7920_CS() {WRITE(ST7920_CS_PIN,1);u8g_10MicroDelay();}
|
||||
#define ST7920_NCS() {WRITE(ST7920_CS_PIN,0);}
|
||||
#define ST7920_SET_CMD() {ST7920_SWSPI_SND_8BIT(0xf8);u8g_10MicroDelay();}
|
||||
#define ST7920_SET_DAT() {ST7920_SWSPI_SND_8BIT(0xfa);u8g_10MicroDelay();}
|
||||
#define ST7920_WRITE_BYTE(a) {ST7920_SWSPI_SND_8BIT((a)&0xf0);ST7920_SWSPI_SND_8BIT((a)<<4);u8g_10MicroDelay();}
|
||||
#define ST7920_WRITE_BYTES(p,l) {uint8_t i;for(i=0;i<l;i++){ST7920_SWSPI_SND_8BIT(*p&0xf0);ST7920_SWSPI_SND_8BIT(*p<<4);p++;}u8g_10MicroDelay();}
|
||||
|
||||
uint8_t u8g_dev_rrd_st7920_128x64_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg)
|
||||
{
|
||||
uint8_t i,y;
|
||||
switch(msg)
|
||||
{
|
||||
case U8G_DEV_MSG_INIT:
|
||||
{
|
||||
SET_OUTPUT(ST7920_CS_PIN);
|
||||
WRITE(ST7920_CS_PIN,0);
|
||||
SET_OUTPUT(ST7920_DAT_PIN);
|
||||
WRITE(ST7920_DAT_PIN,0);
|
||||
SET_OUTPUT(ST7920_CLK_PIN);
|
||||
WRITE(ST7920_CLK_PIN,1);
|
||||
|
||||
ST7920_CS();
|
||||
u8g_Delay(90); //initial delay for boot up
|
||||
ST7920_SET_CMD();
|
||||
ST7920_WRITE_BYTE(0x08); //display off, cursor+blink off
|
||||
ST7920_WRITE_BYTE(0x01); //clear CGRAM ram
|
||||
u8g_Delay(10); //delay for cgram clear
|
||||
ST7920_WRITE_BYTE(0x3E); //extended mode + gdram active
|
||||
for(y=0;y<HEIGHT/2;y++) //clear GDRAM
|
||||
{
|
||||
ST7920_WRITE_BYTE(0x80|y); //set y
|
||||
ST7920_WRITE_BYTE(0x80); //set x = 0
|
||||
ST7920_SET_DAT();
|
||||
for(i=0;i<2*WIDTH/8;i++) //2x width clears both segments
|
||||
ST7920_WRITE_BYTE(0);
|
||||
ST7920_SET_CMD();
|
||||
}
|
||||
ST7920_WRITE_BYTE(0x0C); //display on, cursor+blink off
|
||||
ST7920_NCS();
|
||||
}
|
||||
break;
|
||||
|
||||
case U8G_DEV_MSG_STOP:
|
||||
break;
|
||||
case U8G_DEV_MSG_PAGE_NEXT:
|
||||
{
|
||||
uint8_t *ptr;
|
||||
u8g_pb_t *pb = (u8g_pb_t *)(dev->dev_mem);
|
||||
y = pb->p.page_y0;
|
||||
ptr = (uint8_t*)pb->buf;
|
||||
|
||||
ST7920_CS();
|
||||
for( i = 0; i < PAGE_HEIGHT; i ++ )
|
||||
{
|
||||
ST7920_SET_CMD();
|
||||
if ( y < 32 )
|
||||
{
|
||||
ST7920_WRITE_BYTE(0x80 | y); //y
|
||||
ST7920_WRITE_BYTE(0x80); //x=0
|
||||
}
|
||||
else
|
||||
{
|
||||
ST7920_WRITE_BYTE(0x80 | (y-32)); //y
|
||||
ST7920_WRITE_BYTE(0x80 | 8); //x=64
|
||||
}
|
||||
|
||||
ST7920_SET_DAT();
|
||||
ST7920_WRITE_BYTES(ptr,WIDTH/8); //ptr is incremented inside of macro
|
||||
y++;
|
||||
}
|
||||
ST7920_NCS();
|
||||
}
|
||||
break;
|
||||
}
|
||||
#if PAGE_HEIGHT == 8
|
||||
return u8g_dev_pb8h1_base_fn(u8g, dev, msg, arg);
|
||||
#elif PAGE_HEIGHT == 16
|
||||
return u8g_dev_pb16h1_base_fn(u8g, dev, msg, arg);
|
||||
#else
|
||||
return u8g_dev_pb32h1_base_fn(u8g, dev, msg, arg);
|
||||
#endif
|
||||
}
|
||||
|
||||
uint8_t u8g_dev_st7920_128x64_rrd_buf[WIDTH*(PAGE_HEIGHT/8)] U8G_NOCOMMON;
|
||||
u8g_pb_t u8g_dev_st7920_128x64_rrd_pb = {{PAGE_HEIGHT,HEIGHT,0,0,0},WIDTH,u8g_dev_st7920_128x64_rrd_buf};
|
||||
u8g_dev_t u8g_dev_st7920_128x64_rrd_sw_spi = {u8g_dev_rrd_st7920_128x64_fn,&u8g_dev_st7920_128x64_rrd_pb,&u8g_com_null_fn};
|
||||
|
||||
class U8GLIB_ST7920_128X64_RRD : public U8GLIB
|
||||
{
|
||||
public:
|
||||
U8GLIB_ST7920_128X64_RRD(uint8_t dummy) : U8GLIB(&u8g_dev_st7920_128x64_rrd_sw_spi) {}
|
||||
};
|
||||
|
||||
|
||||
#endif //U8GLIB_ST7920
|
||||
#endif //ULCDST7920_H
|
||||
Loading…
Reference in New Issue
Block a user