Add Formbot Raptor2 and Raise3D pins (#12532)
* Add Formbot Raptor2 board * Add Raise3D Rumba board
This commit is contained in:
InsanityAutomation
Scott Lahteine
parent
6aae199572
commit
dec721c52b
@ -204,12 +204,16 @@ else ifeq ($(HARDWARE_MOTHERBOARD),68)
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),72)
|
||||
# Rumba
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),80)
|
||||
# Raise3D Rumba
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),333)
|
||||
# Formbot T-Rex 2 Plus
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),95)
|
||||
# Formbot T-Rex 3
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),96)
|
||||
# Formbot Raptor
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),97)
|
||||
# Formbot Raptor 2
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),98)
|
||||
# bq ZUM Mega 3D
|
||||
else ifeq ($(HARDWARE_MOTHERBOARD),503)
|
||||
# MakeBoard Mini v2.1.2 is a control board sold by MicroMake
|
||||
|
||||
@ -73,9 +73,11 @@
|
||||
#define BOARD_AZTEEG_X3_PRO 68 // Azteeg X3 Pro
|
||||
#define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
#define BOARD_RUMBA 80 // Rumba
|
||||
#define BOARD_RUMBA_RAISE3D 333 // Raise3D N series Rumba derivative
|
||||
#define BOARD_FORMBOT_TREX2PLUS 95 // Formbot T-Rex 2 Plus
|
||||
#define BOARD_FORMBOT_TREX3 96 // Formbot T-Rex 3
|
||||
#define BOARD_FORMBOT_RAPTOR 97 // Formbot Raptor
|
||||
#define BOARD_FORMBOT_RAPTOR2 98 // Formbot Raptor 2
|
||||
#define BOARD_BQ_ZUM_MEGA_3D 503 // bq ZUM Mega 3D
|
||||
#define BOARD_MAKEBOARD_MINI 431 // MakeBoard Mini v2.1.2 is a control board sold by MicroMake
|
||||
#define BOARD_TRIGORILLA_13 343 // TriGorilla Anycubic version 1.3 based on RAMPS EFB
|
||||
|
||||
@ -132,12 +132,16 @@
|
||||
#include "pins_ULTIMAIN_2.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(FORMBOT_RAPTOR)
|
||||
#include "pins_FORMBOT_RAPTOR.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(FORMBOT_RAPTOR2)
|
||||
#include "pins_FORMBOT_RAPTOR2.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(FORMBOT_TREX2PLUS)
|
||||
#include "pins_FORMBOT_TREX2PLUS.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(FORMBOT_TREX3)
|
||||
#include "pins_FORMBOT_TREX3.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(RUMBA)
|
||||
#include "pins_RUMBA.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(RUMBA_RAISE3D)
|
||||
#include "pins_RUMBA_RAISE3D.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(BQ_ZUM_MEGA_3D)
|
||||
#include "pins_BQ_ZUM_MEGA_3D.h" // ATmega2560 env:megaatmega2560
|
||||
#elif MB(MAKEBOARD_MINI)
|
||||
|
||||
@ -21,7 +21,7 @@
|
||||
*/
|
||||
|
||||
/**
|
||||
* Formbot pin assignments
|
||||
* Formbot Raptor pin assignments
|
||||
*/
|
||||
|
||||
#ifndef __AVR_ATmega2560__
|
||||
@ -32,8 +32,12 @@
|
||||
#error "Formbot supports up to 3 hotends / E-steppers. Comment this line to keep going."
|
||||
#endif
|
||||
|
||||
#define DEFAULT_MACHINE_NAME "Formbot Raptor"
|
||||
#define BOARD_NAME "Formbot Raptor"
|
||||
#ifndef DEFAULT_MACHINE_NAME
|
||||
#define DEFAULT_MACHINE_NAME "Formbot Raptor"
|
||||
#endif
|
||||
#ifndef BOARD_NAME
|
||||
#define BOARD_NAME "Formbot Raptor"
|
||||
#endif
|
||||
|
||||
//
|
||||
// Servos
|
||||
@ -41,7 +45,6 @@
|
||||
#define SERVO0_PIN 11
|
||||
#define SERVO1_PIN 6
|
||||
#define SERVO2_PIN 5
|
||||
#define SERVO3_PIN -1
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
@ -142,7 +145,9 @@
|
||||
#define HEATER_1_PIN 7
|
||||
#define HEATER_BED_PIN 8
|
||||
|
||||
#define FAN_PIN 9
|
||||
#ifndef FAN_PIN
|
||||
#define FAN_PIN 9
|
||||
#endif
|
||||
|
||||
#if DISABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define FAN1_PIN 4
|
||||
@ -151,7 +156,9 @@
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
#define SDSS 53
|
||||
#ifndef SDSS
|
||||
#define SDSS 53
|
||||
#endif
|
||||
#define LED_PIN 13
|
||||
#define LED4_PIN 5
|
||||
|
||||
|
||||
70
Marlin/src/pins/pins_FORMBOT_RAPTOR2.h
Normal file
70
Marlin/src/pins/pins_FORMBOT_RAPTOR2.h
Normal file
@ -0,0 +1,70 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Formbot Raptor 2 pin assignments
|
||||
*/
|
||||
|
||||
#define DEFAULT_MACHINE_NAME "Formbot Raptor2"
|
||||
#define BOARD_NAME "Formbot Raptor2"
|
||||
|
||||
#define FAN_PIN 6
|
||||
#define SDSS 5
|
||||
|
||||
#include "pins_FORMBOT_RAPTOR.h"
|
||||
|
||||
#ifndef FIL_RUNOUT_PIN
|
||||
#define FIL_RUNOUT_PIN 22
|
||||
#endif
|
||||
|
||||
#define GREEDY_PANEL ( ENABLED(PANEL_ONE) || ENABLED(VIKI2) \
|
||||
|| ENABLED(miniVIKI) || ENABLED(MINIPANEL) \
|
||||
|| ENABLED(REPRAPWORLD_KEYPAD) )
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE)
|
||||
#if !NUM_SERVOS // Try to use servo connector first
|
||||
#define SPINDLE_LASER_ENABLE_PIN 6 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 5
|
||||
#elif !GREEDY_PANEL // Try to use AUX2
|
||||
#define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 65
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)
|
||||
#if NUM_SERVOS <= 1 // Try to use servo connector first
|
||||
#define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM
|
||||
#elif !GREEDY_PANEL // Try to use AUX2
|
||||
#define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#undef GREEDY_PANEL
|
||||
|
||||
#if ENABLED(CASE_LIGHT_ENABLE) && PIN_EXISTS(CASE_LIGHT) && (CASE_LIGHT_PIN == SPINDLE_LASER_ENABLE_PIN || CASE_LIGHT_PIN == SPINDLE_LASER_PWM_PIN)
|
||||
#error "CASE_LIGHT_PIN conflicts with a Spindle / Laser pin."
|
||||
#endif
|
||||
@ -32,13 +32,17 @@
|
||||
#error "RUMBA supports up to 3 hotends / E-steppers. Comment out this line to continue."
|
||||
#endif
|
||||
|
||||
#define DEFAULT_MACHINE_NAME "Rumba"
|
||||
#define BOARD_NAME "Rumba"
|
||||
#ifndef DEFAULT_MACHINE_NAME
|
||||
#define DEFAULT_MACHINE_NAME "Rumba"
|
||||
#endif
|
||||
#ifndef BOARD_NAME
|
||||
#define BOARD_NAME "Rumba"
|
||||
#endif
|
||||
|
||||
//
|
||||
// Servos
|
||||
//
|
||||
#define SERVO0_PIN 5
|
||||
#define SERVO0_PIN 5
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
@ -87,16 +91,20 @@
|
||||
//
|
||||
// Temperature Sensors
|
||||
//
|
||||
#if TEMP_SENSOR_0 == -1
|
||||
#define TEMP_0_PIN 6 // Analog Input (connector *K1* on RUMBA thermocouple ADD ON is used)
|
||||
#else
|
||||
#define TEMP_0_PIN 15 // Analog Input (default connector for thermistor *T0* on rumba board is used)
|
||||
#ifndef TEMP_0_PIN
|
||||
#if TEMP_SENSOR_0 == -1
|
||||
#define TEMP_0_PIN 6 // Analog Input (connector *K1* on RUMBA thermocouple ADD ON is used)
|
||||
#else
|
||||
#define TEMP_0_PIN 15 // Analog Input (default connector for thermistor *T0* on rumba board is used)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if TEMP_SENSOR_1 == -1
|
||||
#define TEMP_1_PIN 5 // Analog Input (connector *K2* on RUMBA thermocouple ADD ON is used)
|
||||
#else
|
||||
#define TEMP_1_PIN 14 // Analog Input (default connector for thermistor *T1* on rumba board is used)
|
||||
#ifndef TEMP_1_PIN
|
||||
#if TEMP_SENSOR_1 == -1
|
||||
#define TEMP_1_PIN 5 // Analog Input (connector *K2* on RUMBA thermocouple ADD ON is used)
|
||||
#else
|
||||
#define TEMP_1_PIN 14 // Analog Input (default connector for thermistor *T1* on rumba board is used)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if TEMP_SENSOR_2 == -1
|
||||
@ -105,7 +113,7 @@
|
||||
#define TEMP_2_PIN 13 // Analog Input (default connector for thermistor *T2* on rumba board is used)
|
||||
#endif
|
||||
|
||||
// optional for extruder 4 or chamber:
|
||||
// Optional for extruder 4 or chamber:
|
||||
//#define TEMP_X_PIN 12 // Analog Input (default connector for thermistor *T3* on rumba board is used)
|
||||
//#define TEMP_CHAMBER_PIN 12 // Analog Input (default connector for thermistor *T3* on rumba board is used)
|
||||
|
||||
@ -142,13 +150,13 @@
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#ifndef SPINDLE_LASER_PWM_PIN
|
||||
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM. Pin 4 interrupts OC0* and OC1* always in use?
|
||||
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM. Pin 4 interrupts OC0* and OC1* always in use?
|
||||
#endif
|
||||
#ifndef SPINDLE_LASER_ENABLE_PIN
|
||||
#define SPINDLE_LASER_ENABLE_PIN 14 // Pin should have a pullup!
|
||||
#endif
|
||||
#ifndef SPINDLE_DIR_PIN
|
||||
#define SPINDLE_DIR_PIN 15
|
||||
#define SPINDLE_DIR_PIN 15
|
||||
#endif
|
||||
|
||||
//
|
||||
@ -162,8 +170,8 @@
|
||||
#define BTN_ENC 43
|
||||
|
||||
#if ENABLED(MKS_12864OLED) || ENABLED(MKS_12864OLED_SSD1306)
|
||||
#define LCD_PINS_DC 38 // Set as output on init
|
||||
#define LCD_PINS_RS 41 // Pull low for 1s to init
|
||||
#define LCD_PINS_DC 38 // Set as output on init
|
||||
#define LCD_PINS_RS 41 // Pull low for 1s to init
|
||||
// DOGM SPI LCD Support
|
||||
#define DOGLCD_CS 19
|
||||
#define DOGLCD_MOSI 42
|
||||
|
||||
30
Marlin/src/pins/pins_RUMBA_RAISE3D.h
Normal file
30
Marlin/src/pins/pins_RUMBA_RAISE3D.h
Normal file
@ -0,0 +1,30 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
#define DEFAULT_MACHINE_NAME "Raise3D N Series"
|
||||
#define BOARD_NAME "Raise3D Rumba"
|
||||
|
||||
// Raise3D uses thermocouples on the standard input pins
|
||||
#define TEMP_0_PIN 15 // Analog Input
|
||||
#define TEMP_1_PIN 14 // Analog Input
|
||||
|
||||
#include "pins_RUMBA.h"
|
||||
Loading…
Reference in New Issue
Block a user