Revert 06f767d..cba5692

This rolls back to commit 06f767d608.
This commit is contained in:
Chris Roadfeldt 2015-03-30 23:51:36 -05:00
parent cba5692673
commit e08f8eed05
7 changed files with 409 additions and 600 deletions

View File

@ -229,6 +229,7 @@ void refresh_cmd_timeout(void);
extern float homing_feedrate[];
extern bool axis_relative_modes[];
extern int feedmultiply;
extern int extrudemultiply; // Sets extrude multiply factor (in percent) for all extruders
extern bool volumetric_enabled;
extern int extruder_multiply[EXTRUDERS]; // sets extrude multiply factor (in percent) for each extruder individually
extern float filament_size[EXTRUDERS]; // cross-sectional area of filament (in millimeters), typically around 1.75 or 2.85, 0 disables the volumetric calculations for the extruder.

File diff suppressed because it is too large Load Diff

View File

@ -369,7 +369,7 @@ static void lcd_implementation_status_screen() {
lcd_printPGM(PSTR("dia:"));
lcd_print(ftostr12ns(filament_width_meas));
lcd_printPGM(PSTR(" factor:"));
lcd_print(itostr3(volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM]));
lcd_print(itostr3(extrudemultiply));
lcd_print('%');
}
#endif

View File

@ -545,7 +545,7 @@ float junction_deviation = 0.1;
block->steps[Z_AXIS] = labs(dz);
block->steps[E_AXIS] = labs(de);
block->steps[E_AXIS] *= volumetric_multiplier[active_extruder];
block->steps[E_AXIS] *= extruder_multiply[active_extruder];
block->steps[E_AXIS] *= extrudemultiply;
block->steps[E_AXIS] /= 100;
block->step_event_count = max(block->steps[X_AXIS], max(block->steps[Y_AXIS], max(block->steps[Z_AXIS], block->steps[E_AXIS])));
@ -679,7 +679,7 @@ float junction_deviation = 0.1;
delta_mm[Y_AXIS] = dy / axis_steps_per_unit[Y_AXIS];
#endif
delta_mm[Z_AXIS] = dz / axis_steps_per_unit[Z_AXIS];
delta_mm[E_AXIS] = (de / axis_steps_per_unit[E_AXIS]) * volumetric_multiplier[active_extruder] * extruder_multiply[active_extruder] / 100.0;
delta_mm[E_AXIS] = (de / axis_steps_per_unit[E_AXIS]) * volumetric_multiplier[active_extruder] * extrudemultiply / 100.0;
if (block->steps[X_AXIS] <= dropsegments && block->steps[Y_AXIS] <= dropsegments && block->steps[Z_AXIS] <= dropsegments) {
block->millimeters = fabs(delta_mm[E_AXIS]);

View File

@ -515,36 +515,31 @@ ISR(TIMER1_COMPA_vect) {
}
if (TEST(out_bits, Z_AXIS)) { // -direction
Z_APPLY_DIR(INVERT_Z_DIR,0);
count_direction[Z_AXIS] = -1;
if (check_endstops) {
#if defined(Z_MIN_PIN) && Z_MIN_PIN >= 0
#ifdef Z_DUAL_ENDSTOPS
bool z_min_endstop = READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING,
z2_min_endstop =
#if defined(Z2_MIN_PIN) && Z2_MIN_PIN >= 0
READ(Z2_MIN_PIN) != Z2_MIN_ENDSTOP_INVERTING
#else
z_min_endstop
#endif
;
bool z_min_both = z_min_endstop && old_z_min_endstop,
z2_min_both = z2_min_endstop && old_z2_min_endstop;
if ((z_min_both || z2_min_both) && current_block->steps[Z_AXIS] > 0) {
if (check_endstops)
{
#if defined(Z_MIN_PIN) && Z_MIN_PIN > -1
#ifndef Z_DUAL_ENDSTOPS
UPDATE_ENDSTOP(z, Z, min, MIN);
#else
bool z_min_endstop=(READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING);
#if defined(Z2_MIN_PIN) && Z2_MIN_PIN > -1
bool z2_min_endstop=(READ(Z2_MIN_PIN) != Z2_MIN_ENDSTOP_INVERTING);
#else
bool z2_min_endstop=z_min_endstop;
#endif
if(((z_min_endstop && old_z_min_endstop) || (z2_min_endstop && old_z2_min_endstop)) && (current_block->steps[Z_AXIS] > 0))
{
endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS];
endstop_z_hit = true;
if (!performing_homing || (performing_homing && z_min_both && z2_min_both)) //if not performing home or if both endstops were trigged during homing...
endstop_z_hit=true;
if (!(performing_homing) || ((performing_homing)&&(z_min_endstop && old_z_min_endstop)&&(z2_min_endstop && old_z2_min_endstop))) //if not performing home or if both endstops were trigged during homing...
{
step_events_completed = current_block->step_event_count;
}
}
old_z_min_endstop = z_min_endstop;
old_z2_min_endstop = z2_min_endstop;
<<<<<<< HEAD
#endif
#endif
@ -561,55 +556,37 @@ ISR(TIMER1_COMPA_vect) {
old_z_probe_endstop = z_probe_endstop;
#endif
}
=======
#else // !Z_DUAL_ENDSTOPS
UPDATE_ENDSTOP(z, Z, min, MIN);
#endif // !Z_DUAL_ENDSTOPS
#endif // Z_MIN_PIN
} // check_endstops
>>>>>>> MarlinFirmware/Development
}
else { // +direction
Z_APPLY_DIR(!INVERT_Z_DIR,0);
count_direction[Z_AXIS] = 1;
if (check_endstops) {
#if defined(Z_MAX_PIN) && Z_MAX_PIN >= 0
#ifdef Z_DUAL_ENDSTOPS
bool z_max_endstop = READ(Z_MAX_PIN) != Z_MAX_ENDSTOP_INVERTING,
z2_max_endstop =
#if defined(Z2_MAX_PIN) && Z2_MAX_PIN >= 0
READ(Z2_MAX_PIN) != Z2_MAX_ENDSTOP_INVERTING
#else
z_max_endstop
#endif
;
bool z_max_both = z_max_endstop && old_z_max_endstop,
z2_max_both = z2_max_endstop && old_z2_max_endstop;
if ((z_max_both || z2_max_both) && current_block->steps[Z_AXIS] > 0) {
#ifndef Z_DUAL_ENDSTOPS
UPDATE_ENDSTOP(z, Z, max, MAX);
#else
bool z_max_endstop=(READ(Z_MAX_PIN) != Z_MAX_ENDSTOP_INVERTING);
#if defined(Z2_MAX_PIN) && Z2_MAX_PIN > -1
bool z2_max_endstop=(READ(Z2_MAX_PIN) != Z2_MAX_ENDSTOP_INVERTING);
#else
bool z2_max_endstop=z_max_endstop;
#endif
if(((z_max_endstop && old_z_max_endstop) || (z2_max_endstop && old_z2_max_endstop)) && (current_block->steps[Z_AXIS] > 0))
{
endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS];
endstop_z_hit = true;
endstop_z_hit=true;
// if (z_max_both) SERIAL_ECHOLN("z_max_endstop = true");
// if (z2_max_both) SERIAL_ECHOLN("z2_max_endstop = true");
// if (z_max_endstop && old_z_max_endstop) SERIAL_ECHOLN("z_max_endstop = true");
// if (z2_max_endstop && old_z2_max_endstop) SERIAL_ECHOLN("z2_max_endstop = true");
if (!performing_homing || (performing_homing && z_max_both && z2_max_both)) //if not performing home or if both endstops were trigged during homing...
if (!(performing_homing) || ((performing_homing)&&(z_max_endstop && old_z_max_endstop)&&(z2_max_endstop && old_z2_max_endstop))) //if not performing home or if both endstops were trigged during homing...
{
step_events_completed = current_block->step_event_count;
}
}
old_z_max_endstop = z_max_endstop;
old_z2_max_endstop = z2_max_endstop;
<<<<<<< HEAD
#endif
#endif
@ -626,34 +603,20 @@ ISR(TIMER1_COMPA_vect) {
#endif
}
}
=======
#else // !Z_DUAL_ENDSTOPS
UPDATE_ENDSTOP(z, Z, max, MAX);
#endif // !Z_DUAL_ENDSTOPS
#endif // Z_MAX_PIN
} // check_endstops
} // +direction
>>>>>>> MarlinFirmware/Development
#ifndef ADVANCE
if (TEST(out_bits, E_AXIS)) { // -direction
REV_E_DIR();
count_direction[E_AXIS] = -1;
count_direction[E_AXIS]=-1;
}
else { // +direction
NORM_E_DIR();
count_direction[E_AXIS] = 1;
count_direction[E_AXIS]=1;
}
#endif //!ADVANCE
// Take multiple steps per interrupt (For high speed moves)
for (int8_t i = 0; i < step_loops; i++) {
for (int8_t i=0; i < step_loops; i++) {
#ifndef AT90USB
MSerial.checkRx(); // Check for serial chars.
#endif

View File

@ -485,7 +485,7 @@ static void lcd_tune_menu() {
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_BED, &target_temperature_bed, 0, BED_MAXTEMP - 15);
#endif
MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_FAN_SPEED, &fanSpeed, 0, 255);
MENU_ITEM_EDIT(int3, MSG_FLOW, &extruder_multiply[active_extruder], 10, 999);
MENU_ITEM_EDIT(int3, MSG_FLOW, &extrudemultiply, 10, 999);
MENU_ITEM_EDIT(int3, MSG_FLOW MSG_F0, &extruder_multiply[0], 10, 999);
#if TEMP_SENSOR_1 != 0
MENU_ITEM_EDIT(int3, MSG_FLOW MSG_F1, &extruder_multiply[1], 10, 999);

View File

@ -624,7 +624,7 @@ static void lcd_implementation_status_screen()
static void lcd_implementation_drawmenu_generic(bool sel, uint8_t row, const char* pstr, char pre_char, char post_char) {
char c;
uint8_t n = LCD_WIDTH - 2;
uint8_t n = LCD_WIDTH - 1 - (LCD_WIDTH < 20 ? 1 : 2);
lcd.setCursor(0, row);
lcd.print(sel ? pre_char : ' ');
while ((c = pgm_read_byte(pstr)) && n > 0) {
@ -633,11 +633,12 @@ static void lcd_implementation_drawmenu_generic(bool sel, uint8_t row, const cha
}
while(n--) lcd.print(' ');
lcd.print(post_char);
lcd.print(' ');
}
static void lcd_implementation_drawmenu_setting_edit_generic(bool sel, uint8_t row, const char* pstr, char pre_char, char* data) {
char c;
uint8_t n = LCD_WIDTH - 2 - lcd_strlen(data);
uint8_t n = LCD_WIDTH - 1 - (LCD_WIDTH < 20 ? 1 : 2) - lcd_strlen(data);
lcd.setCursor(0, row);
lcd.print(sel ? pre_char : ' ');
while ((c = pgm_read_byte(pstr)) && n > 0) {
@ -650,7 +651,7 @@ static void lcd_implementation_drawmenu_setting_edit_generic(bool sel, uint8_t r
}
static void lcd_implementation_drawmenu_setting_edit_generic_P(bool sel, uint8_t row, const char* pstr, char pre_char, const char* data) {
char c;
uint8_t n = LCD_WIDTH - 2 - lcd_strlen_P(data);
uint8_t n = LCD_WIDTH - 1 - (LCD_WIDTH < 20 ? 1 : 2) - lcd_strlen_P(data);
lcd.setCursor(0, row);
lcd.print(sel ? pre_char : ' ');
while ((c = pgm_read_byte(pstr)) && n > 0) {
@ -687,11 +688,11 @@ void lcd_implementation_drawedit(const char* pstr, char* value) {
lcd.setCursor(1, 1);
lcd_printPGM(pstr);
lcd.print(':');
lcd.setCursor(LCD_WIDTH - lcd_strlen(value), 1);
lcd.setCursor(LCD_WIDTH - (LCD_WIDTH < 20 ? 0 : 1) - lcd_strlen(value), 1);
lcd_print(value);
}
static void lcd_implementation_drawmenu_sd(bool sel, uint8_t row, const char* pstr, const char* filename, char* longFilename, uint8_t concat, char post_char) {
static void lcd_implementation_drawmenu_sd(bool sel, uint8_t row, const char* pstr, const char* filename, char* longFilename, uint8_t concat) {
char c;
uint8_t n = LCD_WIDTH - concat;
lcd.setCursor(0, row);
@ -705,15 +706,14 @@ static void lcd_implementation_drawmenu_sd(bool sel, uint8_t row, const char* ps
filename++;
}
while (n--) lcd.print(' ');
lcd.print(post_char);
}
static void lcd_implementation_drawmenu_sdfile(bool sel, uint8_t row, const char* pstr, const char* filename, char* longFilename) {
lcd_implementation_drawmenu_sd(sel, row, pstr, filename, longFilename, 2, ' ');
lcd_implementation_drawmenu_sd(sel, row, pstr, filename, longFilename, 1);
}
static void lcd_implementation_drawmenu_sddirectory(bool sel, uint8_t row, const char* pstr, const char* filename, char* longFilename) {
lcd_implementation_drawmenu_sd(sel, row, pstr, filename, longFilename, 2, LCD_STR_FOLDER[0]);
lcd_implementation_drawmenu_sd(sel, row, pstr, filename, longFilename, 2);
}
#define lcd_implementation_drawmenu_back(sel, row, pstr, data) lcd_implementation_drawmenu_generic(sel, row, pstr, LCD_STR_UPLEVEL[0], LCD_STR_UPLEVEL[0])