Added CoreXY support (Thanks Ilan Moyer)
This commit is contained in:
parent
aa65fe22ed
commit
ea2c19f978
@ -35,9 +35,7 @@
|
||||
#define MOTHERBOARD 7
|
||||
#endif
|
||||
|
||||
/// Comment out the following line to enable normal kinematics
|
||||
|
||||
#define COREXY
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
@ -131,6 +129,9 @@
|
||||
//=============================Mechanical Settings===========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// corse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
@ -172,7 +173,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
#define DISABLE_E false // For all extruders
|
||||
|
||||
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
@ -184,8 +185,8 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
|
||||
#define Y_HOME_DIR -1
|
||||
#define Z_HOME_DIR -1
|
||||
|
||||
#define min_software_endstops false //If true, axis won't move to coordinates less than HOME_POS.
|
||||
#define max_software_endstops false //If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
#define min_software_endstops true //If true, axis won't move to coordinates less than HOME_POS.
|
||||
#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
#define X_MAX_LENGTH 205
|
||||
#define Y_MAX_LENGTH 205
|
||||
#define Z_MAX_LENGTH 200
|
||||
|
@ -488,16 +488,16 @@ ISR(TIMER1_COMPA_vect)
|
||||
if (counter_x > 0) {
|
||||
WRITE(X_STEP_PIN, HIGH);
|
||||
counter_x -= current_block->step_event_count;
|
||||
WRITE(X_STEP_PIN, LOW);
|
||||
count_position[X_AXIS]+=count_direction[X_AXIS];
|
||||
WRITE(X_STEP_PIN, LOW);
|
||||
}
|
||||
|
||||
counter_y += current_block->steps_y;
|
||||
if (counter_y > 0) {
|
||||
WRITE(Y_STEP_PIN, HIGH);
|
||||
|
||||
counter_y -= current_block->step_event_count;
|
||||
count_position[Y_AXIS]+=count_direction[Y_AXIS];
|
||||
WRITE(Y_STEP_PIN, LOW);
|
||||
|
||||
}
|
||||
#endif
|
||||
|
||||
@ -508,19 +508,19 @@ ISR(TIMER1_COMPA_vect)
|
||||
if ((counter_x > 0)&&!(counter_y>0)){ //X step only
|
||||
WRITE(X_STEP_PIN, HIGH);
|
||||
WRITE(Y_STEP_PIN, HIGH);
|
||||
counter_x -= current_block->step_event_count;
|
||||
counter_x -= current_block->step_event_count;
|
||||
count_position[X_AXIS]+=count_direction[X_AXIS];
|
||||
WRITE(X_STEP_PIN, LOW);
|
||||
WRITE(Y_STEP_PIN, LOW);
|
||||
count_position[X_AXIS]+=count_direction[X_AXIS];
|
||||
}
|
||||
|
||||
if (!(counter_x > 0)&&(counter_y>0)){ //Y step only
|
||||
WRITE(X_STEP_PIN, HIGH);
|
||||
WRITE(Y_STEP_PIN, HIGH);
|
||||
counter_y -= current_block->step_event_count;
|
||||
counter_y -= current_block->step_event_count;
|
||||
count_position[Y_AXIS]+=count_direction[Y_AXIS];
|
||||
WRITE(X_STEP_PIN, LOW);
|
||||
WRITE(Y_STEP_PIN, LOW);
|
||||
count_position[Y_AXIS]+=count_direction[Y_AXIS];
|
||||
}
|
||||
|
||||
if ((counter_x > 0)&&(counter_y>0)){ //step in both axes
|
||||
@ -553,8 +553,8 @@ ISR(TIMER1_COMPA_vect)
|
||||
if (counter_z > 0) {
|
||||
WRITE(Z_STEP_PIN, HIGH);
|
||||
counter_z -= current_block->step_event_count;
|
||||
WRITE(Z_STEP_PIN, LOW);
|
||||
count_position[Z_AXIS]+=count_direction[Z_AXIS];
|
||||
WRITE(Z_STEP_PIN, LOW);
|
||||
}
|
||||
|
||||
#ifndef ADVANCE
|
||||
@ -562,8 +562,8 @@ ISR(TIMER1_COMPA_vect)
|
||||
if (counter_e > 0) {
|
||||
WRITE_E_STEP(HIGH);
|
||||
counter_e -= current_block->step_event_count;
|
||||
WRITE_E_STEP(LOW);
|
||||
count_position[E_AXIS]+=count_direction[E_AXIS];
|
||||
WRITE_E_STEP(LOW);
|
||||
}
|
||||
#endif //!ADVANCE
|
||||
step_events_completed += 1;
|
||||
|
@ -44,6 +44,7 @@ Features:
|
||||
* Updated sdcardlib
|
||||
* Heater power reporting. Useful for PID monitoring.
|
||||
* PID tuning
|
||||
* CoreXY kinematics (www.corexy.com/theory.html)
|
||||
|
||||
The default baudrate is 250000. This baudrate has less jitter and hence errors than the usual 115200 baud, but is less supported by drivers and host-environments.
|
||||
|
||||
|
Loading…
Reference in New Issue
Block a user