From f101e1925779d4d44f89804eeb9cb62a4eaf999e Mon Sep 17 00:00:00 2001 From: George Fu Date: Sun, 17 Jan 2021 14:46:57 +0800 Subject: [PATCH] FYSETC_242 OLED 12864 for S6 (#20767) --- Marlin/src/lcd/dogm/HAL_LCD_class_defines.h | 13 ++ Marlin/src/lcd/dogm/HAL_LCD_com_defines.h | 2 + Marlin/src/lcd/dogm/marlinui_DOGM.h | 16 ++- Marlin/src/lcd/dogm/u8g_dev_ssd1309_12864.cpp | 128 ++++++++++++++++++ Marlin/src/pins/stm32f4/pins_FYSETC_S6.h | 59 ++++---- 5 files changed, 192 insertions(+), 26 deletions(-) create mode 100644 Marlin/src/lcd/dogm/u8g_dev_ssd1309_12864.cpp diff --git a/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h b/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h index 1511c6993..30a5361ab 100644 --- a/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h +++ b/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h @@ -107,3 +107,16 @@ public: : U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset) { } }; + +extern u8g_dev_t u8g_dev_ssd1309_sw_spi; +extern u8g_dev_t u8g_dev_ssd1309_hw_spi; + +class U8GLIB_SSD1309_128X64_HAL : public U8GLIB { +public: + U8GLIB_SSD1309_128X64_HAL(pin_t sck, pin_t mosi, pin_t cs, pin_t a0, pin_t reset = U8G_PIN_NONE) + : U8GLIB(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset) + { } + U8GLIB_SSD1309_128X64_HAL(pin_t cs, pin_t a0, pin_t reset = U8G_PIN_NONE) + : U8GLIB(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset) + { } +}; diff --git a/Marlin/src/lcd/dogm/HAL_LCD_com_defines.h b/Marlin/src/lcd/dogm/HAL_LCD_com_defines.h index 535502f2e..8a707ab41 100644 --- a/Marlin/src/lcd/dogm/HAL_LCD_com_defines.h +++ b/Marlin/src/lcd/dogm/HAL_LCD_com_defines.h @@ -52,7 +52,9 @@ #elif defined(ARDUINO_ARCH_STM32) + uint8_t u8g_com_std_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); uint8_t u8g_com_stm32duino_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); + #define U8G_COM_HAL_SW_SPI_FN u8g_com_std_sw_spi_fn #define U8G_COM_HAL_HW_SPI_FN u8g_com_stm32duino_hw_spi_fn #elif defined(__AVR__) diff --git a/Marlin/src/lcd/dogm/marlinui_DOGM.h b/Marlin/src/lcd/dogm/marlinui_DOGM.h index 16cb70dbd..e5229cd08 100644 --- a/Marlin/src/lcd/dogm/marlinui_DOGM.h +++ b/Marlin/src/lcd/dogm/marlinui_DOGM.h @@ -110,11 +110,9 @@ #define U8G_CLASS U8GLIB_MINI12864_2X // 8 stripes (HW-SPI) #endif -#elif EITHER(MKS_12864OLED_SSD1306, FYSETC_242_OLED_12864) +#elif ENABLED(MKS_12864OLED_SSD1306) // MKS 128x64 (SSD1306) OLED I2C LCD - // - or - - // FYSETC OLED 2.42" 128 × 64 FULL GRAPHICS CONTROLLER #define FORCE_SOFT_SPI // SW-SPI @@ -124,6 +122,18 @@ #define U8G_CLASS U8GLIB_SSD1306_128X64 // 8 stripes #endif +#elif ENABLED(FYSETC_242_OLED_12864) + + // FYSETC OLED 2.42" 128 × 64 FULL GRAPHICS CONTROLLER + + #define FORCE_SOFT_SPI // SW-SPI + + #if ENABLED(ALTERNATIVE_LCD) + #define U8G_CLASS U8GLIB_SSD1306_128X64_2X // 4 stripes + #else + #define U8G_CLASS U8GLIB_SSD1309_128X64_HAL + #endif + #elif ENABLED(ZONESTAR_12864OLED_SSD1306) // Zonestar SSD1306 OLED SPI LCD diff --git a/Marlin/src/lcd/dogm/u8g_dev_ssd1309_12864.cpp b/Marlin/src/lcd/dogm/u8g_dev_ssd1309_12864.cpp new file mode 100644 index 000000000..8ba19216b --- /dev/null +++ b/Marlin/src/lcd/dogm/u8g_dev_ssd1309_12864.cpp @@ -0,0 +1,128 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#include "../../inc/MarlinConfigPre.h" + +#if HAS_MARLINUI_U8GLIB + +#include "HAL_LCD_com_defines.h" +#include + +#define WIDTH 128 +#define HEIGHT 64 +#define PAGE_HEIGHT 8 + +// SSD1309 init sequence +static const uint8_t u8g_dev_ssd1309_128x64_init_seq[] PROGMEM = { + U8G_ESC_CS(0), // Disable chip + U8G_ESC_ADR(0), // Instruction mode + U8G_ESC_RST(1), // Do reset low pulse with (1*16)+2 milliseconds + U8G_ESC_CS(1), // Enable chip + + 0xFD,0x12, // Command Lock + 0xAE, // Set Display Off + 0xD5,0xA0, // Set Display Clock Divide Ratio/Oscillator Frequency + 0xA8,0x3F, // Set Multiplex Ratio + 0x3D,0x00, // Set Display Offset + 0x40, // Set Display Start Line + 0xA1, // Set Segment Re-Map + 0xC8, // Set COM Output Scan Direction + 0xDA,0x12, // Set COM Pins Hardware Configuration + 0x81,0xDF, // Set Current Control + 0xD9,0x82, // Set Pre-Charge Period + 0xDB,0x34, // Set VCOMH Deselect Level + 0xA4, // Set Entire Display On/Off + 0xA6, // Set Normal/Inverse Display + U8G_ESC_VCC(1), // Power up VCC & Stabilized + U8G_ESC_DLY(50), + 0xAF, // Set Display On + U8G_ESC_DLY(50), + U8G_ESC_CS(0), // Disable chip + U8G_ESC_END // End of sequence +}; + +// Select one init sequence here +#define u8g_dev_ssd1309_128x64_init_seq u8g_dev_ssd1309_128x64_init_seq + +static const uint8_t u8g_dev_ssd1309_128x64_data_start[] PROGMEM = { + U8G_ESC_ADR(0), // Instruction mode + U8G_ESC_CS(1), // Enable chip + 0x010, // Set upper 4 bit of the col adr to 0 + 0x000, // Set lower 4 bit of the col adr to 4 + U8G_ESC_END // End of sequence +}; + +static const uint8_t u8g_dev_ssd13xx_sleep_on[] PROGMEM = { + U8G_ESC_ADR(0), // Instruction mode + U8G_ESC_CS(1), // Enable chip + 0x0AE, // Display off + U8G_ESC_CS(0), // Disable chip + U8G_ESC_END // End of sequence +}; + +static const uint8_t u8g_dev_ssd13xx_sleep_off[] PROGMEM = { + U8G_ESC_ADR(0), // Instruction mode + U8G_ESC_CS(1), // Enable chip + 0x0AF, // Display on + U8G_ESC_DLY(50), // Delay 50 ms + U8G_ESC_CS(0), // Disable chip + U8G_ESC_END // End of sequence +}; + +uint8_t u8g_dev_ssd1309_128x64_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) { + switch(msg) { + case U8G_DEV_MSG_INIT: + u8g_InitCom(u8g, dev, U8G_SPI_CLK_CYCLE_300NS); + u8g_WriteEscSeqP(u8g, dev, u8g_dev_ssd1309_128x64_init_seq); + break; + case U8G_DEV_MSG_STOP: + break; + case U8G_DEV_MSG_PAGE_NEXT: { + u8g_pb_t *pb = (u8g_pb_t *)(dev->dev_mem); + u8g_WriteEscSeqP(u8g, dev, u8g_dev_ssd1309_128x64_data_start); + u8g_WriteByte(u8g, dev, 0x0B0 | pb->p.page); // Select current page (SSD1306) + u8g_SetAddress(u8g, dev, 1); // Data mode + if (u8g_pb_WriteBuffer(pb, u8g, dev) == 0) return 0; + u8g_SetChipSelect(u8g, dev, 0); + } + break; + case U8G_DEV_MSG_CONTRAST: + u8g_SetChipSelect(u8g, dev, 1); + u8g_SetAddress(u8g, dev, 0); // Instruction mode + u8g_WriteByte(u8g, dev, 0x081); + u8g_WriteByte(u8g, dev, (*(uint8_t *)arg) ); // 11 Jul 2015: fixed contrast calculation + u8g_SetChipSelect(u8g, dev, 0); + return 1; + case U8G_DEV_MSG_SLEEP_ON: + u8g_WriteEscSeqP(u8g, dev, u8g_dev_ssd13xx_sleep_on); + return 1; + case U8G_DEV_MSG_SLEEP_OFF: + u8g_WriteEscSeqP(u8g, dev, u8g_dev_ssd13xx_sleep_off); + return 1; + } + return u8g_dev_pb8v1_base_fn(u8g, dev, msg, arg); +} + +uint8_t u8g_dev_ssd1309_buf[WIDTH*2] U8G_NOCOMMON ; +u8g_pb_t u8g_dev_ssd1309_pb = { {8, HEIGHT, 0, 0, 0}, WIDTH, u8g_dev_ssd1309_buf}; +u8g_dev_t u8g_dev_ssd1309_sw_spi = { u8g_dev_ssd1309_128x64_fn, &u8g_dev_ssd1309_pb, U8G_COM_HAL_SW_SPI_FN }; + +#endif // HAS_MARLINUI_U8GLIB diff --git a/Marlin/src/pins/stm32f4/pins_FYSETC_S6.h b/Marlin/src/pins/stm32f4/pins_FYSETC_S6.h index 7d435c8cd..a28077564 100644 --- a/Marlin/src/pins/stm32f4/pins_FYSETC_S6.h +++ b/Marlin/src/pins/stm32f4/pins_FYSETC_S6.h @@ -198,7 +198,27 @@ // // LCD / Controller // -#if HAS_WIRED_LCD +#if ENABLED(FYSETC_242_OLED_12864) + + #define BTN_EN1 PC9 + #define BTN_EN2 PD1 + #define BTN_ENC PA8 + + #define BEEPER_PIN PC6 + + #define LCD_PINS_DC PC12 + #define LCD_PINS_RS PC7 // LCD_RST + #define DOGLCD_CS PD2 + #define DOGLCD_MOSI PC10 + #define DOGLCD_SCK PC11 + #define DOGLCD_A0 LCD_PINS_DC + #define FORCE_SOFT_SPI + + #define KILL_PIN -1 // NC + #define NEOPIXEL_PIN PD0 + +#elif HAS_WIRED_LCD + #define BEEPER_PIN PC9 #define BTN_ENC PA8 @@ -211,11 +231,6 @@ #define LCD_PINS_ENABLE PD1 #define LCD_PINS_D4 PC12 - // CR10_STOCKDISPLAY default timing is too fast - #undef BOARD_ST7920_DELAY_1 - #undef BOARD_ST7920_DELAY_2 - #undef BOARD_ST7920_DELAY_3 - #else #define LCD_PINS_RS PD2 @@ -229,7 +244,7 @@ #define LCD_PINS_D4 PC10 #if ENABLED(FYSETC_MINI_12864) - // See https://wiki.fysetc.com/Mini12864_Panel + // See https://wiki.fysetc.com/Mini12864_Panel #define DOGLCD_CS PC11 #define DOGLCD_A0 PD2 #if ENABLED(FYSETC_GENERIC_12864_1_1) @@ -249,36 +264,34 @@ #elif ENABLED(FYSETC_MINI_12864_2_1) #define NEOPIXEL_PIN PC12 #endif - #endif // !FYSETC_MINI_12864 + #endif #if IS_ULTIPANEL #define LCD_PINS_D5 PC12 #define LCD_PINS_D6 PD0 #define LCD_PINS_D7 PD1 - #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder #endif - #endif #endif - // Alter timing for graphical display - #if HAS_MARLINUI_U8GLIB - #ifndef BOARD_ST7920_DELAY_1 - #define BOARD_ST7920_DELAY_1 DELAY_NS(96) - #endif - #ifndef BOARD_ST7920_DELAY_2 - #define BOARD_ST7920_DELAY_2 DELAY_NS(48) - #endif - #ifndef BOARD_ST7920_DELAY_3 - #define BOARD_ST7920_DELAY_3 DELAY_NS(640) - #endif - #endif - #endif // HAS_WIRED_LCD +// Alter timing for graphical display +#if HAS_MARLINUI_U8GLIB + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(96) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(48) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(640) + #endif +#endif + #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN PB6 #endif