Update default/Configuration_adv.h
This commit is contained in:
parent
49027721e9
commit
f39d025a80
@ -1732,7 +1732,6 @@
|
||||
//#define E5_CS_PIN -1
|
||||
|
||||
/**
|
||||
* Use software SPI for TMC2130.
|
||||
* Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160).
|
||||
* The default SW SPI pins are defined the respective pins files,
|
||||
* but you can override or define them here.
|
||||
@ -1774,7 +1773,7 @@
|
||||
//#define SOFTWARE_DRIVER_ENABLE
|
||||
|
||||
/**
|
||||
* TMC2130, TMC2160, TMC2208, TMC5130 and TMC5160 only
|
||||
* TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
|
||||
* Use Trinamic's ultra quiet stepping mode.
|
||||
* When disabled, Marlin will use spreadCycle stepping mode.
|
||||
*/
|
||||
@ -1800,7 +1799,7 @@
|
||||
|
||||
/**
|
||||
* Monitor Trinamic drivers for error conditions,
|
||||
* like overtemperature and short to ground. TMC2208 requires hardware serial.
|
||||
* like overtemperature and short to ground.
|
||||
* In the case of overtemperature Marlin can decrease the driver current until error condition clears.
|
||||
* Other detected conditions can be used to stop the current print.
|
||||
* Relevant g-codes:
|
||||
@ -1818,7 +1817,7 @@
|
||||
#endif
|
||||
|
||||
/**
|
||||
* TMC2130, TMC2160, TMC2208, TMC5130 and TMC5160 only
|
||||
* TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
|
||||
* The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
|
||||
* This mode allows for faster movements at the expense of higher noise levels.
|
||||
* STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
|
||||
@ -1841,7 +1840,7 @@
|
||||
#define E5_HYBRID_THRESHOLD 30
|
||||
|
||||
/**
|
||||
* TMC2130, TMC2160, TMC2660, TMC5130, and TMC5160 only
|
||||
* TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
|
||||
* Use StallGuard2 to sense an obstacle and trigger an endstop.
|
||||
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
|
||||
* X, Y, and Z homing will always be done in spreadCycle mode.
|
||||
@ -1853,7 +1852,7 @@
|
||||
* It is advised to set X/Y/Z_HOME_BUMP_MM to 0.
|
||||
* M914 X/Y/Z to live tune the setting
|
||||
*/
|
||||
//#define SENSORLESS_HOMING // TMC2130 only
|
||||
//#define SENSORLESS_HOMING // StallGuard capable drivers only
|
||||
|
||||
/**
|
||||
* Use StallGuard2 to probe the bed with the nozzle.
|
||||
@ -1861,9 +1860,10 @@
|
||||
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
|
||||
* to move the Z axis. Take extreme care when attempting to enable this feature.
|
||||
*/
|
||||
//#define SENSORLESS_PROBING // TMC2130 only
|
||||
//#define SENSORLESS_PROBING // StallGuard capable drivers only
|
||||
|
||||
#if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
|
||||
// TMC2209: 0...255. TMC2130: -64...63
|
||||
#define X_STALL_SENSITIVITY 8
|
||||
#define Y_STALL_SENSITIVITY 8
|
||||
//#define Z_STALL_SENSITIVITY 8
|
||||
|
Loading…
Reference in New Issue
Block a user