From f0aee4101a21ed2607e6e2d43622252f78b42818 Mon Sep 17 00:00:00 2001 From: whosawhatsis Date: Fri, 8 Mar 2013 13:41:49 -0800 Subject: [PATCH 1/8] regenerated thermistor table 7 Generated with createTemperatureLookup.py. The old table crapped out at 270C, which was a problem for polycarbonate. --- Marlin/thermistortables.h | 112 +++++++++++++++++++------------------- 1 file changed, 57 insertions(+), 55 deletions(-) diff --git a/Marlin/thermistortables.h b/Marlin/thermistortables.h index 76ea32b7b..f8839b096 100644 --- a/Marlin/thermistortables.h +++ b/Marlin/thermistortables.h @@ -254,61 +254,63 @@ const short temptable_6[][2] PROGMEM = { #if (THERMISTORHEATER_0 == 7) || (THERMISTORHEATER_1 == 7) || (THERMISTORHEATER_2 == 7) || (THERMISTORBED == 7) // 100k Honeywell 135-104LAG-J01 const short temptable_7[][2] PROGMEM = { - {1*OVERSAMPLENR, 500}, - {46*OVERSAMPLENR, 270}, //top rating 300C - {50*OVERSAMPLENR, 265}, - {54*OVERSAMPLENR, 260}, - {58*OVERSAMPLENR, 255}, - {62*OVERSAMPLENR, 250}, - {67*OVERSAMPLENR, 245}, - {72*OVERSAMPLENR, 240}, - {79*OVERSAMPLENR, 235}, - {85*OVERSAMPLENR, 230}, - {91*OVERSAMPLENR, 225}, - {99*OVERSAMPLENR, 220}, - {107*OVERSAMPLENR, 215}, - {116*OVERSAMPLENR, 210}, - {126*OVERSAMPLENR, 205}, - {136*OVERSAMPLENR, 200}, - {149*OVERSAMPLENR, 195}, - {160*OVERSAMPLENR, 190}, - {175*OVERSAMPLENR, 185}, - {191*OVERSAMPLENR, 180}, - {209*OVERSAMPLENR, 175}, - {224*OVERSAMPLENR, 170}, - {246*OVERSAMPLENR, 165}, - {267*OVERSAMPLENR, 160}, - {293*OVERSAMPLENR, 155}, - {316*OVERSAMPLENR, 150}, - {340*OVERSAMPLENR, 145}, - {364*OVERSAMPLENR, 140}, - {396*OVERSAMPLENR, 135}, - {425*OVERSAMPLENR, 130}, - {460*OVERSAMPLENR, 125}, - {489*OVERSAMPLENR, 120}, - {526*OVERSAMPLENR, 115}, - {558*OVERSAMPLENR, 110}, - {591*OVERSAMPLENR, 105}, - {628*OVERSAMPLENR, 100}, - {660*OVERSAMPLENR, 95}, - {696*OVERSAMPLENR, 90}, - {733*OVERSAMPLENR, 85}, - {761*OVERSAMPLENR, 80}, - {794*OVERSAMPLENR, 75}, - {819*OVERSAMPLENR, 70}, - {847*OVERSAMPLENR, 65}, - {870*OVERSAMPLENR, 60}, - {892*OVERSAMPLENR, 55}, - {911*OVERSAMPLENR, 50}, - {929*OVERSAMPLENR, 45}, - {944*OVERSAMPLENR, 40}, - {959*OVERSAMPLENR, 35}, - {971*OVERSAMPLENR, 30}, - {981*OVERSAMPLENR, 25}, - {989*OVERSAMPLENR, 20}, - {994*OVERSAMPLENR, 15}, - {1001*OVERSAMPLENR, 10}, - {1005*OVERSAMPLENR, 5}, + {1*OVERSAMPLENR, 941}, + {19*OVERSAMPLENR, 362}, + {37*OVERSAMPLENR, 299}, //top rating 300C + {55*OVERSAMPLENR, 266}, + {73*OVERSAMPLENR, 245}, + {91*OVERSAMPLENR, 229}, + {109*OVERSAMPLENR, 216}, + {127*OVERSAMPLENR, 206}, + {145*OVERSAMPLENR, 197}, + {163*OVERSAMPLENR, 190}, + {181*OVERSAMPLENR, 183}, + {199*OVERSAMPLENR, 177}, + {217*OVERSAMPLENR, 171}, + {235*OVERSAMPLENR, 166}, + {253*OVERSAMPLENR, 162}, + {271*OVERSAMPLENR, 157}, + {289*OVERSAMPLENR, 153}, + {307*OVERSAMPLENR, 149}, + {325*OVERSAMPLENR, 146}, + {343*OVERSAMPLENR, 142}, + {361*OVERSAMPLENR, 139}, + {379*OVERSAMPLENR, 135}, + {397*OVERSAMPLENR, 132}, + {415*OVERSAMPLENR, 129}, + {433*OVERSAMPLENR, 126}, + {451*OVERSAMPLENR, 123}, + {469*OVERSAMPLENR, 121}, + {487*OVERSAMPLENR, 118}, + {505*OVERSAMPLENR, 115}, + {523*OVERSAMPLENR, 112}, + {541*OVERSAMPLENR, 110}, + {559*OVERSAMPLENR, 107}, + {577*OVERSAMPLENR, 105}, + {595*OVERSAMPLENR, 102}, + {613*OVERSAMPLENR, 99}, + {631*OVERSAMPLENR, 97}, + {649*OVERSAMPLENR, 94}, + {667*OVERSAMPLENR, 92}, + {685*OVERSAMPLENR, 89}, + {703*OVERSAMPLENR, 86}, + {721*OVERSAMPLENR, 84}, + {739*OVERSAMPLENR, 81}, + {757*OVERSAMPLENR, 78}, + {775*OVERSAMPLENR, 75}, + {793*OVERSAMPLENR, 72}, + {811*OVERSAMPLENR, 69}, + {829*OVERSAMPLENR, 66}, + {847*OVERSAMPLENR, 62}, + {865*OVERSAMPLENR, 59}, + {883*OVERSAMPLENR, 55}, + {901*OVERSAMPLENR, 51}, + {919*OVERSAMPLENR, 46}, + {937*OVERSAMPLENR, 41}, + {955*OVERSAMPLENR, 35}, + {973*OVERSAMPLENR, 27}, + {991*OVERSAMPLENR, 17}, + {1009*OVERSAMPLENR, 1} {1023*OVERSAMPLENR, 0} //to allow internal 0 degrees C }; #endif From 6a61a3c0b4365d4d0887dbbff94d38e452cbe4c7 Mon Sep 17 00:00:00 2001 From: whosawhatsis Date: Fri, 8 Mar 2013 16:15:49 -0800 Subject: [PATCH 2/8] missing comma in last commit --- Marlin/thermistortables.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Marlin/thermistortables.h b/Marlin/thermistortables.h index f8839b096..e3d28ba28 100644 --- a/Marlin/thermistortables.h +++ b/Marlin/thermistortables.h @@ -310,7 +310,7 @@ const short temptable_7[][2] PROGMEM = { {955*OVERSAMPLENR, 35}, {973*OVERSAMPLENR, 27}, {991*OVERSAMPLENR, 17}, - {1009*OVERSAMPLENR, 1} + {1009*OVERSAMPLENR, 1}, {1023*OVERSAMPLENR, 0} //to allow internal 0 degrees C }; #endif From 7c47e7162d725c61764e43e2817878f55cecdd2a Mon Sep 17 00:00:00 2001 From: Ryan Turner Date: Mon, 18 Mar 2013 22:53:37 -0500 Subject: [PATCH 3/8] Adding Maker's Tool Works heated bed thermistor --- Marlin/thermistortables.h | 78 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 78 insertions(+) diff --git a/Marlin/thermistortables.h b/Marlin/thermistortables.h index 76ea32b7b..8496ae1be 100644 --- a/Marlin/thermistortables.h +++ b/Marlin/thermistortables.h @@ -554,6 +554,84 @@ const short temptable_55[][2] PROGMEM = { }; #endif +#if (THERMISTORHEATER_0 == 60) || (THERMISTORHEATER_1 == 60) || (THERMISTORHEATER_2 == 60) || (THERMISTORBED == 60) // Maker's Tool Works Kapton Bed Thermister +const short temptable_60[][2] PROGMEM = { + {51*OVERSAMPLENR, 272}, + {61*OVERSAMPLENR, 258}, + {71*OVERSAMPLENR, 247}, + {81*OVERSAMPLENR, 237}, + {91*OVERSAMPLENR, 229}, + {101*OVERSAMPLENR, 221}, + {131*OVERSAMPLENR, 204}, + {161*OVERSAMPLENR, 190}, + {191*OVERSAMPLENR, 179}, + {231*OVERSAMPLENR, 167}, + {271*OVERSAMPLENR, 157}, + {311*OVERSAMPLENR, 148}, + {351*OVERSAMPLENR, 140}, + {381*OVERSAMPLENR, 135}, + {411*OVERSAMPLENR, 130}, + {441*OVERSAMPLENR, 125}, + {451*OVERSAMPLENR, 123}, + {461*OVERSAMPLENR, 122}, + {471*OVERSAMPLENR, 120}, + {481*OVERSAMPLENR, 119}, + {491*OVERSAMPLENR, 117}, + {501*OVERSAMPLENR, 116}, + {511*OVERSAMPLENR, 114}, + {521*OVERSAMPLENR, 113}, + {531*OVERSAMPLENR, 111}, + {541*OVERSAMPLENR, 110}, + {551*OVERSAMPLENR, 108}, + {561*OVERSAMPLENR, 107}, + {571*OVERSAMPLENR, 105}, + {581*OVERSAMPLENR, 104}, + {591*OVERSAMPLENR, 102}, + {601*OVERSAMPLENR, 101}, + {611*OVERSAMPLENR, 100}, + {621*OVERSAMPLENR, 98}, + {631*OVERSAMPLENR, 97}, + {641*OVERSAMPLENR, 95}, + {651*OVERSAMPLENR, 94}, + {661*OVERSAMPLENR, 92}, + {671*OVERSAMPLENR, 91}, + {681*OVERSAMPLENR, 90}, + {691*OVERSAMPLENR, 88}, + {701*OVERSAMPLENR, 87}, + {711*OVERSAMPLENR, 85}, + {721*OVERSAMPLENR, 84}, + {731*OVERSAMPLENR, 82}, + {741*OVERSAMPLENR, 81}, + {751*OVERSAMPLENR, 79}, + {761*OVERSAMPLENR, 77}, + {771*OVERSAMPLENR, 76}, + {781*OVERSAMPLENR, 74}, + {791*OVERSAMPLENR, 72}, + {801*OVERSAMPLENR, 71}, + {811*OVERSAMPLENR, 69}, + {821*OVERSAMPLENR, 67}, + {831*OVERSAMPLENR, 65}, + {841*OVERSAMPLENR, 63}, + {851*OVERSAMPLENR, 62}, + {861*OVERSAMPLENR, 60}, + {871*OVERSAMPLENR, 57}, + {881*OVERSAMPLENR, 55}, + {891*OVERSAMPLENR, 53}, + {901*OVERSAMPLENR, 51}, + {911*OVERSAMPLENR, 48}, + {921*OVERSAMPLENR, 45}, + {931*OVERSAMPLENR, 42}, + {941*OVERSAMPLENR, 39}, + {951*OVERSAMPLENR, 36}, + {961*OVERSAMPLENR, 32}, + {981*OVERSAMPLENR, 23}, + {991*OVERSAMPLENR, 17}, + {1001*OVERSAMPLENR, 9}, + {1008*OVERSAMPLENR, 0}, +}; +#endif + + #define _TT_NAME(_N) temptable_ ## _N #define TT_NAME(_N) _TT_NAME(_N) From d2b00fe48627eb9b5c3b78720c3faa83cbc69e6a Mon Sep 17 00:00:00 2001 From: blddk Date: Fri, 22 Mar 2013 18:28:16 +0100 Subject: [PATCH 4/8] Removed html and added rumba Found some unwanted html at the bottom of the file which caused it to not be able to compile. Also added rumba as machine. --- Marlin/language.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/Marlin/language.h b/Marlin/language.h index d17f6f667..51d40a284 100644 --- a/Marlin/language.h +++ b/Marlin/language.h @@ -26,6 +26,9 @@ #if MOTHERBOARD == 7 || MOTHERBOARD == 71 #define MACHINE_NAME "Ultimaker" #define FIRMWARE_URL "http://firmware.ultimaker.com" +#elif MOTHERBOARD == 80 + #define MACHINE_NAME "Rumba" + #define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/" #else #define MACHINE_NAME "Mendel" #define FIRMWARE_URL "http://www.mendel-parts.com" @@ -1461,5 +1464,4 @@ #define MSG_ERR_LONG_EXTRUDE_STOP " liian pitka pursotus estetty" #endif -#endif // ifndef LANGUAGE_H - \ No newline at end of file +#endif // ifndef LANGUAGE_H From 91bea433328568e6da2659141a37a926689aa9b4 Mon Sep 17 00:00:00 2001 From: blddk Date: Fri, 22 Mar 2013 18:29:47 +0100 Subject: [PATCH 5/8] Added rumba pinout --- Marlin/pins.h | 87 +++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 87 insertions(+) diff --git a/Marlin/pins.h b/Marlin/pins.h index f1babfa70..6191ed288 100644 --- a/Marlin/pins.h +++ b/Marlin/pins.h @@ -979,6 +979,93 @@ #endif + +/**************************************************************************************** +* RUMBA pin assignment +* +****************************************************************************************/ +#if MOTHERBOARD == 80 +#define KNOWN_BOARD 1 + +#ifndef __AVR_ATmega2560__ + #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. +#endif + +#define X_STEP_PIN 17 +#define X_DIR_PIN 16 +#define X_ENABLE_PIN 48 +#define X_MIN_PIN 37 +#define X_MAX_PIN 36 + +#define Y_STEP_PIN 54 +#define Y_DIR_PIN 47 +#define Y_ENABLE_PIN 55 +#define Y_MIN_PIN 35 +#define Y_MAX_PIN 34 + +#define Z_STEP_PIN 57 +#define Z_DIR_PIN 56 +#define Z_ENABLE_PIN 62 +#define Z_MIN_PIN 33 +#define Z_MAX_PIN 32 + +#define E0_STEP_PIN 23 +#define E0_DIR_PIN 22 +#define E0_ENABLE_PIN 24 + +#define E1_STEP_PIN 26 +#define E1_DIR_PIN 25 +#define E1_ENABLE_PIN 27 + +#define E2_STEP_PIN 29 +#define E2_DIR_PIN 28 +#define E2_ENABLE_PIN 39 + +#define LED_PIN 13 + +#define FAN_PIN 7 +//additional FAN1 PIN (e.g. useful for electronics fan or light on/off) on PIN 8 + +#define PS_ON_PIN 45 +#define KILL_PIN 46 + +#define HEATER_0_PIN 2 // EXTRUDER 1 +#define HEATER_1_PIN 3 // EXTRUDER 2 +#define HEATER_2_PIN 6 // EXTRUDER 3 +//optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN 8 // EXTRUDER 4 +#define HEATER_BED_PIN 9 // BED + +#define TEMP_0_PIN 15 // ANALOG NUMBERING +#define TEMP_1_PIN 14 // ANALOG NUMBERING +#define TEMP_2_PIN 13 // ANALOG NUMBERING +//optional for extruder 4 or chamber: #define TEMP_2_PIN 12 // ANALOG NUMBERING +#define TEMP_BED_PIN 11 // ANALOG NUMBERING + +#define SDPOWER -1 +#define SDSS 53 +#define SDCARDDETECT 49 +#define BEEPER 44 +#define LCD_PINS_RS 19 +#define LCD_PINS_ENABLE 42 +#define LCD_PINS_D4 18 +#define LCD_PINS_D5 38 +#define LCD_PINS_D6 41 +#define LCD_PINS_D7 40 +#define BTN_EN1 11 +#define BTN_EN2 12 +#define BTN_ENC 43 +//encoder rotation values +#define BLEN_C 2 +#define BLEN_B 1 +#define BLEN_A 0 +#define encrot0 0 +#define encrot1 2 +#define encrot2 3 +#define encrot3 1 + +#endif //MOTHERBOARD==80 + + /**************************************************************************************** * Teensylu 0.7 / Printrboard pin assignments (AT90USB1286) * Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE! From 72419f69a91b13faab3c62dd62a918a6f5e3fc23 Mon Sep 17 00:00:00 2001 From: blddk Date: Fri, 22 Mar 2013 18:41:54 +0100 Subject: [PATCH 6/8] Added rumba --- Marlin/Configuration.h | 1 + 1 file changed, 1 insertion(+) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 8031272db..54929bac3 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -38,6 +38,7 @@ // 7 = Ultimaker // 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare) // 8 = Teensylu +// 80 = Rumba // 81 = Printrboard (AT90USB1286) // 82 = Brainwave (AT90USB646) // 9 = Gen3+ From e5a853a3d01732633b99156b3466013a1b4016c7 Mon Sep 17 00:00:00 2001 From: blddk Date: Fri, 22 Mar 2013 18:49:05 +0100 Subject: [PATCH 7/8] Added automated extruder fan function --- Marlin/Marlin_main.cpp | 4285 ++++++++++++++++++++-------------------- 1 file changed, 2157 insertions(+), 2128 deletions(-) diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp index 372554617..fa3681ec7 100644 --- a/Marlin/Marlin_main.cpp +++ b/Marlin/Marlin_main.cpp @@ -1,2132 +1,2161 @@ -/* -*- c++ -*- */ - -/* - Reprap firmware based on Sprinter and grbl. - Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm - - This program is free software: you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation, either version 3 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program. If not, see . - */ - -/* - This firmware is a mashup between Sprinter and grbl. - (https://github.com/kliment/Sprinter) - (https://github.com/simen/grbl/tree) - - It has preliminary support for Matthew Roberts advance algorithm - http://reprap.org/pipermail/reprap-dev/2011-May/003323.html - */ - -#include "Marlin.h" - -#include "ultralcd.h" -#include "planner.h" -#include "stepper.h" -#include "temperature.h" -#include "motion_control.h" -#include "cardreader.h" -#include "watchdog.h" -#include "ConfigurationStore.h" -#include "language.h" -#include "pins_arduino.h" - -#if DIGIPOTSS_PIN > -1 -#include -#endif - -#define VERSION_STRING "1.0.0" - -// look here for descriptions of gcodes: http://linuxcnc.org/handbook/gcode/g-code.html -// http://objects.reprap.org/wiki/Mendel_User_Manual:_RepRapGCodes - -//Implemented Codes -//------------------- -// G0 -> G1 -// G1 - Coordinated Movement X Y Z E -// G2 - CW ARC -// G3 - CCW ARC -// G4 - Dwell S or P -// G10 - retract filament according to settings of M207 -// G11 - retract recover filament according to settings of M208 -// G28 - Home all Axis -// G90 - Use Absolute Coordinates -// G91 - Use Relative Coordinates -// G92 - Set current position to cordinates given - -//RepRap M Codes -// M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled) -// M1 - Same as M0 -// M104 - Set extruder target temp -// M105 - Read current temp -// M106 - Fan on -// M107 - Fan off -// M109 - Wait for extruder current temp to reach target temp. -// M114 - Display current position - -//Custom M Codes -// M17 - Enable/Power all stepper motors -// M18 - Disable all stepper motors; same as M84 -// M20 - List SD card -// M21 - Init SD card -// M22 - Release SD card -// M23 - Select SD file (M23 filename.g) -// M24 - Start/resume SD print -// M25 - Pause SD print -// M26 - Set SD position in bytes (M26 S12345) -// M27 - Report SD print status -// M28 - Start SD write (M28 filename.g) -// M29 - Stop SD write -// M30 - Delete file from SD (M30 filename.g) -// M31 - Output time since last M109 or SD card start to serial -// M42 - Change pin status via gcode Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used. -// M80 - Turn on Power Supply -// M81 - Turn off Power Supply -// M82 - Set E codes absolute (default) -// M83 - Set E codes relative while in Absolute Coordinates (G90) mode -// M84 - Disable steppers until next move, -// or use S to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout. -// M85 - Set inactivity shutdown timer with parameter S. To disable set zero (default) -// M92 - Set axis_steps_per_unit - same syntax as G92 -// M114 - Output current position to serial port -// M115 - Capabilities string -// M117 - display message -// M119 - Output Endstop status to serial port -// M140 - Set bed target temp -// M190 - Wait for bed current temp to reach target temp. -// M200 - Set filament diameter -// M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000) -// M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!! -// M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec -// M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate -// M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk -// M206 - set additional homeing offset -// M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop] -// M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec] -// M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. -// M218 - set hotend offset (in mm): T X Y -// M220 S- set speed factor override percentage -// M221 S- set extrude factor override percentage -// M240 - Trigger a camera to take a photograph -// M301 - Set PID parameters P I and D -// M302 - Allow cold extrudes -// M303 - PID relay autotune S sets the target temperature. (default target temperature = 150C) -// M304 - Set bed PID parameters P I and D -// M400 - Finish all moves -// M500 - stores paramters in EEPROM -// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). -// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. -// M503 - print the current settings (from memory not from eeprom) -// M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) -// M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] -// M907 - Set digital trimpot motor current using axis codes. -// M908 - Control digital trimpot directly. -// M350 - Set microstepping mode. -// M351 - Toggle MS1 MS2 pins directly. -// M999 - Restart after being stopped by error - -//Stepper Movement Variables - -//=========================================================================== -//=============================imported variables============================ -//=========================================================================== - - -//=========================================================================== -//=============================public variables============================= -//=========================================================================== -#ifdef SDSUPPORT -CardReader card; -#endif -float homing_feedrate[] = HOMING_FEEDRATE; -bool axis_relative_modes[] = AXIS_RELATIVE_MODES; -int feedmultiply=100; //100->1 200->2 -int saved_feedmultiply; -int extrudemultiply=100; //100->1 200->2 -float current_position[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0 }; -float add_homeing[3]={0,0,0}; -float min_pos[3] = { X_MIN_POS, Y_MIN_POS, Z_MIN_POS }; -float max_pos[3] = { X_MAX_POS, Y_MAX_POS, Z_MAX_POS }; -// Extruder offset, only in XY plane +/* -*- c++ -*- */ + +/* + Reprap firmware based on Sprinter and grbl. + Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + + This program is free software: you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation, either version 3 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program. If not, see . + */ + +/* + This firmware is a mashup between Sprinter and grbl. + (https://github.com/kliment/Sprinter) + (https://github.com/simen/grbl/tree) + + It has preliminary support for Matthew Roberts advance algorithm + http://reprap.org/pipermail/reprap-dev/2011-May/003323.html + */ + +#include "Marlin.h" + +#include "ultralcd.h" +#include "planner.h" +#include "stepper.h" +#include "temperature.h" +#include "motion_control.h" +#include "cardreader.h" +#include "watchdog.h" +#include "ConfigurationStore.h" +#include "language.h" +#include "pins_arduino.h" + +#if DIGIPOTSS_PIN > -1 +#include +#endif + +#define VERSION_STRING "1.0.0" + +// look here for descriptions of gcodes: http://linuxcnc.org/handbook/gcode/g-code.html +// http://objects.reprap.org/wiki/Mendel_User_Manual:_RepRapGCodes + +//Implemented Codes +//------------------- +// G0 -> G1 +// G1 - Coordinated Movement X Y Z E +// G2 - CW ARC +// G3 - CCW ARC +// G4 - Dwell S or P +// G10 - retract filament according to settings of M207 +// G11 - retract recover filament according to settings of M208 +// G28 - Home all Axis +// G90 - Use Absolute Coordinates +// G91 - Use Relative Coordinates +// G92 - Set current position to cordinates given + +//RepRap M Codes +// M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled) +// M1 - Same as M0 +// M104 - Set extruder target temp +// M105 - Read current temp +// M106 - Fan on +// M107 - Fan off +// M109 - Wait for extruder current temp to reach target temp. +// M114 - Display current position + +//Custom M Codes +// M17 - Enable/Power all stepper motors +// M18 - Disable all stepper motors; same as M84 +// M20 - List SD card +// M21 - Init SD card +// M22 - Release SD card +// M23 - Select SD file (M23 filename.g) +// M24 - Start/resume SD print +// M25 - Pause SD print +// M26 - Set SD position in bytes (M26 S12345) +// M27 - Report SD print status +// M28 - Start SD write (M28 filename.g) +// M29 - Stop SD write +// M30 - Delete file from SD (M30 filename.g) +// M31 - Output time since last M109 or SD card start to serial +// M42 - Change pin status via gcode Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used. +// M80 - Turn on Power Supply +// M81 - Turn off Power Supply +// M82 - Set E codes absolute (default) +// M83 - Set E codes relative while in Absolute Coordinates (G90) mode +// M84 - Disable steppers until next move, +// or use S to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout. +// M85 - Set inactivity shutdown timer with parameter S. To disable set zero (default) +// M92 - Set axis_steps_per_unit - same syntax as G92 +// M114 - Output current position to serial port +// M115 - Capabilities string +// M117 - display message +// M119 - Output Endstop status to serial port +// M140 - Set bed target temp +// M190 - Wait for bed current temp to reach target temp. +// M200 - Set filament diameter +// M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000) +// M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!! +// M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec +// M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate +// M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk +// M206 - set additional homeing offset +// M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop] +// M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec] +// M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. +// M218 - set hotend offset (in mm): T X Y +// M220 S- set speed factor override percentage +// M221 S- set extrude factor override percentage +// M240 - Trigger a camera to take a photograph +// M301 - Set PID parameters P I and D +// M302 - Allow cold extrudes +// M303 - PID relay autotune S sets the target temperature. (default target temperature = 150C) +// M304 - Set bed PID parameters P I and D +// M400 - Finish all moves +// M500 - stores paramters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +// M503 - print the current settings (from memory not from eeprom) +// M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) +// M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] +// M907 - Set digital trimpot motor current using axis codes. +// M908 - Control digital trimpot directly. +// M350 - Set microstepping mode. +// M351 - Toggle MS1 MS2 pins directly. +// M999 - Restart after being stopped by error + +//Stepper Movement Variables + +//=========================================================================== +//=============================imported variables============================ +//=========================================================================== + + +//=========================================================================== +//=============================public variables============================= +//=========================================================================== +#ifdef SDSUPPORT +CardReader card; +#endif +float homing_feedrate[] = HOMING_FEEDRATE; +bool axis_relative_modes[] = AXIS_RELATIVE_MODES; +int feedmultiply=100; //100->1 200->2 +int saved_feedmultiply; +int extrudemultiply=100; //100->1 200->2 +float current_position[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0 }; +float add_homeing[3]={0,0,0}; +float min_pos[3] = { X_MIN_POS, Y_MIN_POS, Z_MIN_POS }; +float max_pos[3] = { X_MAX_POS, Y_MAX_POS, Z_MAX_POS }; +// Extruder offset, only in XY plane #if EXTRUDERS > 1 -float extruder_offset[2][EXTRUDERS] = { -#if defined(EXTRUDER_OFFSET_X) && defined(EXTRUDER_OFFSET_Y) - EXTRUDER_OFFSET_X, EXTRUDER_OFFSET_Y -#endif +float extruder_offset[2][EXTRUDERS] = { +#if defined(EXTRUDER_OFFSET_X) && defined(EXTRUDER_OFFSET_Y) + EXTRUDER_OFFSET_X, EXTRUDER_OFFSET_Y +#endif }; -#endif -uint8_t active_extruder = 0; -int fanSpeed=0; - -#ifdef FWRETRACT - bool autoretract_enabled=true; - bool retracted=false; - float retract_length=3, retract_feedrate=17*60, retract_zlift=0.8; - float retract_recover_length=0, retract_recover_feedrate=8*60; -#endif - -//=========================================================================== -//=============================private variables============================= -//=========================================================================== -const char axis_codes[NUM_AXIS] = {'X', 'Y', 'Z', 'E'}; -static float destination[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0}; -static float offset[3] = {0.0, 0.0, 0.0}; -static bool home_all_axis = true; -static float feedrate = 1500.0, next_feedrate, saved_feedrate; -static long gcode_N, gcode_LastN, Stopped_gcode_LastN = 0; - -static bool relative_mode = false; //Determines Absolute or Relative Coordinates - -static char cmdbuffer[BUFSIZE][MAX_CMD_SIZE]; -static bool fromsd[BUFSIZE]; -static int bufindr = 0; -static int bufindw = 0; -static int buflen = 0; -//static int i = 0; -static char serial_char; -static int serial_count = 0; -static boolean comment_mode = false; -static char *strchr_pointer; // just a pointer to find chars in the cmd string like X, Y, Z, E, etc - -const int sensitive_pins[] = SENSITIVE_PINS; // Sensitive pin list for M42 - -//static float tt = 0; -//static float bt = 0; - -//Inactivity shutdown variables -static unsigned long previous_millis_cmd = 0; -static unsigned long max_inactive_time = 0; -static unsigned long stepper_inactive_time = DEFAULT_STEPPER_DEACTIVE_TIME*1000l; - -unsigned long starttime=0; -unsigned long stoptime=0; - -static uint8_t tmp_extruder; - - -bool Stopped=false; - -//=========================================================================== -//=============================ROUTINES============================= -//=========================================================================== - -void get_arc_coordinates(); -bool setTargetedHotend(int code); - -void serial_echopair_P(const char *s_P, float v) - { serialprintPGM(s_P); SERIAL_ECHO(v); } -void serial_echopair_P(const char *s_P, double v) - { serialprintPGM(s_P); SERIAL_ECHO(v); } -void serial_echopair_P(const char *s_P, unsigned long v) - { serialprintPGM(s_P); SERIAL_ECHO(v); } - -extern "C"{ - extern unsigned int __bss_end; - extern unsigned int __heap_start; - extern void *__brkval; - - int freeMemory() { - int free_memory; - - if((int)__brkval == 0) - free_memory = ((int)&free_memory) - ((int)&__bss_end); - else - free_memory = ((int)&free_memory) - ((int)__brkval); - - return free_memory; - } -} - -//adds an command to the main command buffer -//thats really done in a non-safe way. -//needs overworking someday -void enquecommand(const char *cmd) -{ - if(buflen < BUFSIZE) - { - //this is dangerous if a mixing of serial and this happsens - strcpy(&(cmdbuffer[bufindw][0]),cmd); - SERIAL_ECHO_START; - SERIAL_ECHOPGM("enqueing \""); - SERIAL_ECHO(cmdbuffer[bufindw]); - SERIAL_ECHOLNPGM("\""); - bufindw= (bufindw + 1)%BUFSIZE; - buflen += 1; - } -} - -void enquecommand_P(const char *cmd) -{ - if(buflen < BUFSIZE) - { - //this is dangerous if a mixing of serial and this happsens - strcpy_P(&(cmdbuffer[bufindw][0]),cmd); - SERIAL_ECHO_START; - SERIAL_ECHOPGM("enqueing \""); - SERIAL_ECHO(cmdbuffer[bufindw]); - SERIAL_ECHOLNPGM("\""); - bufindw= (bufindw + 1)%BUFSIZE; - buflen += 1; - } -} - -void setup_killpin() -{ - #if( KILL_PIN>-1 ) - pinMode(KILL_PIN,INPUT); - WRITE(KILL_PIN,HIGH); - #endif -} - -void setup_photpin() -{ - #ifdef PHOTOGRAPH_PIN - #if (PHOTOGRAPH_PIN > -1) - SET_OUTPUT(PHOTOGRAPH_PIN); - WRITE(PHOTOGRAPH_PIN, LOW); - #endif - #endif -} - -void setup_powerhold() -{ - #ifdef SUICIDE_PIN - #if (SUICIDE_PIN> -1) - SET_OUTPUT(SUICIDE_PIN); - WRITE(SUICIDE_PIN, HIGH); - #endif - #endif - #if (PS_ON_PIN > -1) - SET_OUTPUT(PS_ON_PIN); - WRITE(PS_ON_PIN, PS_ON_AWAKE); - #endif -} - -void suicide() -{ - #ifdef SUICIDE_PIN - #if (SUICIDE_PIN> -1) - SET_OUTPUT(SUICIDE_PIN); - WRITE(SUICIDE_PIN, LOW); - #endif - #endif -} - -void setup() -{ - setup_killpin(); - setup_powerhold(); - MYSERIAL.begin(BAUDRATE); - SERIAL_PROTOCOLLNPGM("start"); - SERIAL_ECHO_START; - - // Check startup - does nothing if bootloader sets MCUSR to 0 - byte mcu = MCUSR; - if(mcu & 1) SERIAL_ECHOLNPGM(MSG_POWERUP); - if(mcu & 2) SERIAL_ECHOLNPGM(MSG_EXTERNAL_RESET); - if(mcu & 4) SERIAL_ECHOLNPGM(MSG_BROWNOUT_RESET); - if(mcu & 8) SERIAL_ECHOLNPGM(MSG_WATCHDOG_RESET); - if(mcu & 32) SERIAL_ECHOLNPGM(MSG_SOFTWARE_RESET); - MCUSR=0; - - SERIAL_ECHOPGM(MSG_MARLIN); - SERIAL_ECHOLNPGM(VERSION_STRING); - #ifdef STRING_VERSION_CONFIG_H - #ifdef STRING_CONFIG_H_AUTHOR - SERIAL_ECHO_START; - SERIAL_ECHOPGM(MSG_CONFIGURATION_VER); - SERIAL_ECHOPGM(STRING_VERSION_CONFIG_H); - SERIAL_ECHOPGM(MSG_AUTHOR); - SERIAL_ECHOLNPGM(STRING_CONFIG_H_AUTHOR); - SERIAL_ECHOPGM("Compiled: "); - SERIAL_ECHOLNPGM(__DATE__); - #endif - #endif - SERIAL_ECHO_START; - SERIAL_ECHOPGM(MSG_FREE_MEMORY); - SERIAL_ECHO(freeMemory()); - SERIAL_ECHOPGM(MSG_PLANNER_BUFFER_BYTES); - SERIAL_ECHOLN((int)sizeof(block_t)*BLOCK_BUFFER_SIZE); - for(int8_t i = 0; i < BUFSIZE; i++) - { - fromsd[i] = false; - } - - Config_RetrieveSettings(); // loads data from EEPROM if available - - for(int8_t i=0; i < NUM_AXIS; i++) - { - axis_steps_per_sqr_second[i] = max_acceleration_units_per_sq_second[i] * axis_steps_per_unit[i]; - } - - - tp_init(); // Initialize temperature loop - plan_init(); // Initialize planner; - watchdog_init(); - st_init(); // Initialize stepper, this enables interrupts! - setup_photpin(); - - lcd_init(); -} - - -void loop() -{ - if(buflen < (BUFSIZE-1)) - get_command(); - #ifdef SDSUPPORT - card.checkautostart(false); - #endif - if(buflen) - { - #ifdef SDSUPPORT - if(card.saving) - { - if(strstr_P(cmdbuffer[bufindr], PSTR("M29")) == NULL) - { - card.write_command(cmdbuffer[bufindr]); - SERIAL_PROTOCOLLNPGM(MSG_OK); - } - else - { - card.closefile(); - SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED); - } - } - else - { - process_commands(); - } - #else - process_commands(); - #endif //SDSUPPORT - buflen = (buflen-1); - bufindr = (bufindr + 1)%BUFSIZE; - } - //check heater every n milliseconds - manage_heater(); - manage_inactivity(); - checkHitEndstops(); - lcd_update(); -} - -void get_command() -{ - while( MYSERIAL.available() > 0 && buflen < BUFSIZE) { - serial_char = MYSERIAL.read(); - if(serial_char == '\n' || - serial_char == '\r' || - (serial_char == ':' && comment_mode == false) || - serial_count >= (MAX_CMD_SIZE - 1) ) - { - if(!serial_count) { //if empty line - comment_mode = false; //for new command - return; - } - cmdbuffer[bufindw][serial_count] = 0; //terminate string - if(!comment_mode){ - comment_mode = false; //for new command - fromsd[bufindw] = false; - if(strchr(cmdbuffer[bufindw], 'N') != NULL) - { - strchr_pointer = strchr(cmdbuffer[bufindw], 'N'); - gcode_N = (strtol(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL, 10)); - if(gcode_N != gcode_LastN+1 && (strstr_P(cmdbuffer[bufindw], PSTR("M110")) == NULL) ) { - SERIAL_ERROR_START; - SERIAL_ERRORPGM(MSG_ERR_LINE_NO); - SERIAL_ERRORLN(gcode_LastN); - //Serial.println(gcode_N); - FlushSerialRequestResend(); - serial_count = 0; - return; - } - - if(strchr(cmdbuffer[bufindw], '*') != NULL) - { - byte checksum = 0; - byte count = 0; - while(cmdbuffer[bufindw][count] != '*') checksum = checksum^cmdbuffer[bufindw][count++]; - strchr_pointer = strchr(cmdbuffer[bufindw], '*'); - - if( (int)(strtod(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL)) != checksum) { - SERIAL_ERROR_START; - SERIAL_ERRORPGM(MSG_ERR_CHECKSUM_MISMATCH); - SERIAL_ERRORLN(gcode_LastN); - FlushSerialRequestResend(); - serial_count = 0; - return; - } - //if no errors, continue parsing - } - else - { - SERIAL_ERROR_START; - SERIAL_ERRORPGM(MSG_ERR_NO_CHECKSUM); - SERIAL_ERRORLN(gcode_LastN); - FlushSerialRequestResend(); - serial_count = 0; - return; - } - - gcode_LastN = gcode_N; - //if no errors, continue parsing - } - else // if we don't receive 'N' but still see '*' - { - if((strchr(cmdbuffer[bufindw], '*') != NULL)) - { - SERIAL_ERROR_START; - SERIAL_ERRORPGM(MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM); - SERIAL_ERRORLN(gcode_LastN); - serial_count = 0; - return; - } - } - if((strchr(cmdbuffer[bufindw], 'G') != NULL)){ - strchr_pointer = strchr(cmdbuffer[bufindw], 'G'); - switch((int)((strtod(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL)))){ - case 0: - case 1: - case 2: - case 3: - if(Stopped == false) { // If printer is stopped by an error the G[0-3] codes are ignored. - #ifdef SDSUPPORT - if(card.saving) - break; - #endif //SDSUPPORT - SERIAL_PROTOCOLLNPGM(MSG_OK); - } - else { - SERIAL_ERRORLNPGM(MSG_ERR_STOPPED); - LCD_MESSAGEPGM(MSG_STOPPED); - } - break; - default: - break; - } - - } - bufindw = (bufindw + 1)%BUFSIZE; - buflen += 1; - } - serial_count = 0; //clear buffer - } - else - { - if(serial_char == ';') comment_mode = true; - if(!comment_mode) cmdbuffer[bufindw][serial_count++] = serial_char; - } - } - #ifdef SDSUPPORT - if(!card.sdprinting || serial_count!=0){ - return; - } - while( !card.eof() && buflen < BUFSIZE) { - int16_t n=card.get(); - serial_char = (char)n; - if(serial_char == '\n' || - serial_char == '\r' || - (serial_char == ':' && comment_mode == false) || - serial_count >= (MAX_CMD_SIZE - 1)||n==-1) - { - if(card.eof()){ - SERIAL_PROTOCOLLNPGM(MSG_FILE_PRINTED); - stoptime=millis(); - char time[30]; - unsigned long t=(stoptime-starttime)/1000; - int hours, minutes; - minutes=(t/60)%60; - hours=t/60/60; - sprintf_P(time, PSTR("%i hours %i minutes"),hours, minutes); - SERIAL_ECHO_START; - SERIAL_ECHOLN(time); - lcd_setstatus(time); - card.printingHasFinished(); - card.checkautostart(true); - - } - if(!serial_count) - { - comment_mode = false; //for new command - return; //if empty line - } - cmdbuffer[bufindw][serial_count] = 0; //terminate string -// if(!comment_mode){ - fromsd[bufindw] = true; - buflen += 1; - bufindw = (bufindw + 1)%BUFSIZE; -// } - comment_mode = false; //for new command - serial_count = 0; //clear buffer - } - else - { - if(serial_char == ';') comment_mode = true; - if(!comment_mode) cmdbuffer[bufindw][serial_count++] = serial_char; - } - } - - #endif //SDSUPPORT - -} - - -float code_value() -{ - return (strtod(&cmdbuffer[bufindr][strchr_pointer - cmdbuffer[bufindr] + 1], NULL)); -} - -long code_value_long() -{ - return (strtol(&cmdbuffer[bufindr][strchr_pointer - cmdbuffer[bufindr] + 1], NULL, 10)); -} - -bool code_seen(char code) -{ - strchr_pointer = strchr(cmdbuffer[bufindr], code); - return (strchr_pointer != NULL); //Return True if a character was found -} - -#define DEFINE_PGM_READ_ANY(type, reader) \ - static inline type pgm_read_any(const type *p) \ - { return pgm_read_##reader##_near(p); } - -DEFINE_PGM_READ_ANY(float, float); -DEFINE_PGM_READ_ANY(signed char, byte); - -#define XYZ_CONSTS_FROM_CONFIG(type, array, CONFIG) \ -static const PROGMEM type array##_P[3] = \ - { X_##CONFIG, Y_##CONFIG, Z_##CONFIG }; \ -static inline type array(int axis) \ - { return pgm_read_any(&array##_P[axis]); } - -XYZ_CONSTS_FROM_CONFIG(float, base_min_pos, MIN_POS); -XYZ_CONSTS_FROM_CONFIG(float, base_max_pos, MAX_POS); -XYZ_CONSTS_FROM_CONFIG(float, base_home_pos, HOME_POS); -XYZ_CONSTS_FROM_CONFIG(float, max_length, MAX_LENGTH); -XYZ_CONSTS_FROM_CONFIG(float, home_retract_mm, HOME_RETRACT_MM); -XYZ_CONSTS_FROM_CONFIG(signed char, home_dir, HOME_DIR); - -static void axis_is_at_home(int axis) { - current_position[axis] = base_home_pos(axis) + add_homeing[axis]; - min_pos[axis] = base_min_pos(axis) + add_homeing[axis]; - max_pos[axis] = base_max_pos(axis) + add_homeing[axis]; -} - -static void homeaxis(int axis) { -#define HOMEAXIS_DO(LETTER) \ - ((LETTER##_MIN_PIN > -1 && LETTER##_HOME_DIR==-1) || (LETTER##_MAX_PIN > -1 && LETTER##_HOME_DIR==1)) - - if (axis==X_AXIS ? HOMEAXIS_DO(X) : - axis==Y_AXIS ? HOMEAXIS_DO(Y) : - axis==Z_AXIS ? HOMEAXIS_DO(Z) : - 0) { - current_position[axis] = 0; - plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); - destination[axis] = 1.5 * max_length(axis) * home_dir(axis); - feedrate = homing_feedrate[axis]; - plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); - st_synchronize(); - - current_position[axis] = 0; - plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); - destination[axis] = -home_retract_mm(axis) * home_dir(axis); - plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); - st_synchronize(); - - destination[axis] = 2*home_retract_mm(axis) * home_dir(axis); - feedrate = homing_feedrate[axis]/2 ; - plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); - st_synchronize(); - - axis_is_at_home(axis); - destination[axis] = current_position[axis]; - feedrate = 0.0; - endstops_hit_on_purpose(); - } -} -#define HOMEAXIS(LETTER) homeaxis(LETTER##_AXIS) - -void process_commands() -{ - unsigned long codenum; //throw away variable - char *starpos = NULL; - - if(code_seen('G')) - { - switch((int)code_value()) - { - case 0: // G0 -> G1 - case 1: // G1 - if(Stopped == false) { - get_coordinates(); // For X Y Z E F - prepare_move(); - //ClearToSend(); - return; - } - //break; - case 2: // G2 - CW ARC - if(Stopped == false) { - get_arc_coordinates(); - prepare_arc_move(true); - return; - } - case 3: // G3 - CCW ARC - if(Stopped == false) { - get_arc_coordinates(); - prepare_arc_move(false); - return; - } - case 4: // G4 dwell - LCD_MESSAGEPGM(MSG_DWELL); - codenum = 0; - if(code_seen('P')) codenum = code_value(); // milliseconds to wait - if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait - - st_synchronize(); - codenum += millis(); // keep track of when we started waiting - previous_millis_cmd = millis(); - while(millis() < codenum ){ - manage_heater(); - manage_inactivity(); - lcd_update(); - } - break; - #ifdef FWRETRACT - case 10: // G10 retract - if(!retracted) - { - destination[X_AXIS]=current_position[X_AXIS]; - destination[Y_AXIS]=current_position[Y_AXIS]; - destination[Z_AXIS]=current_position[Z_AXIS]; - current_position[Z_AXIS]+=-retract_zlift; - destination[E_AXIS]=current_position[E_AXIS]-retract_length; - feedrate=retract_feedrate; - retracted=true; - prepare_move(); - } - - break; - case 11: // G10 retract_recover - if(!retracted) - { - destination[X_AXIS]=current_position[X_AXIS]; - destination[Y_AXIS]=current_position[Y_AXIS]; - destination[Z_AXIS]=current_position[Z_AXIS]; - - current_position[Z_AXIS]+=retract_zlift; - current_position[E_AXIS]+=-retract_recover_length; - feedrate=retract_recover_feedrate; - retracted=false; - prepare_move(); - } - break; - #endif //FWRETRACT - case 28: //G28 Home all Axis one at a time - saved_feedrate = feedrate; - saved_feedmultiply = feedmultiply; - feedmultiply = 100; - previous_millis_cmd = millis(); - - enable_endstops(true); - - for(int8_t i=0; i < NUM_AXIS; i++) { - destination[i] = current_position[i]; - } - feedrate = 0.0; - home_all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))); - - #if Z_HOME_DIR > 0 // If homing away from BED do Z first - if((home_all_axis) || (code_seen(axis_codes[Z_AXIS]))) { - HOMEAXIS(Z); - } - #endif - - #ifdef QUICK_HOME - if((home_all_axis)||( code_seen(axis_codes[X_AXIS]) && code_seen(axis_codes[Y_AXIS])) ) //first diagonal move - { - current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0; - - plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); - destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR; - feedrate = homing_feedrate[X_AXIS]; - if(homing_feedrate[Y_AXIS] 0){ - codenum += millis(); // keep track of when we started waiting - while(millis() < codenum && !LCD_CLICKED){ - manage_heater(); - manage_inactivity(); - lcd_update(); - } - }else{ - while(!LCD_CLICKED){ - manage_heater(); - manage_inactivity(); - lcd_update(); - } - } - LCD_MESSAGEPGM(MSG_RESUMING); - } - break; -#endif - case 17: - LCD_MESSAGEPGM(MSG_NO_MOVE); - enable_x(); - enable_y(); - enable_z(); - enable_e0(); - enable_e1(); - enable_e2(); - break; - -#ifdef SDSUPPORT - case 20: // M20 - list SD card - SERIAL_PROTOCOLLNPGM(MSG_BEGIN_FILE_LIST); - card.ls(); - SERIAL_PROTOCOLLNPGM(MSG_END_FILE_LIST); - break; - case 21: // M21 - init SD card - - card.initsd(); - - break; - case 22: //M22 - release SD card - card.release(); - - break; - case 23: //M23 - Select file - starpos = (strchr(strchr_pointer + 4,'*')); - if(starpos!=NULL) - *(starpos-1)='\0'; - card.openFile(strchr_pointer + 4,true); - break; - case 24: //M24 - Start SD print - card.startFileprint(); - starttime=millis(); - break; - case 25: //M25 - Pause SD print - card.pauseSDPrint(); - break; - case 26: //M26 - Set SD index - if(card.cardOK && code_seen('S')) { - card.setIndex(code_value_long()); - } - break; - case 27: //M27 - Get SD status - card.getStatus(); - break; - case 28: //M28 - Start SD write - starpos = (strchr(strchr_pointer + 4,'*')); - if(starpos != NULL){ - char* npos = strchr(cmdbuffer[bufindr], 'N'); - strchr_pointer = strchr(npos,' ') + 1; - *(starpos-1) = '\0'; - } - card.openFile(strchr_pointer+4,false); - break; - case 29: //M29 - Stop SD write - //processed in write to file routine above - //card,saving = false; - break; - case 30: //M30 Delete File - if (card.cardOK){ - card.closefile(); - starpos = (strchr(strchr_pointer + 4,'*')); - if(starpos != NULL){ - char* npos = strchr(cmdbuffer[bufindr], 'N'); - strchr_pointer = strchr(npos,' ') + 1; - *(starpos-1) = '\0'; - } - card.removeFile(strchr_pointer + 4); - } - break; - -#endif //SDSUPPORT - - case 31: //M31 take time since the start of the SD print or an M109 command - { - stoptime=millis(); - char time[30]; - unsigned long t=(stoptime-starttime)/1000; - int sec,min; - min=t/60; - sec=t%60; - sprintf_P(time, PSTR("%i min, %i sec"), min, sec); - SERIAL_ECHO_START; - SERIAL_ECHOLN(time); - lcd_setstatus(time); - autotempShutdown(); - } - break; - case 42: //M42 -Change pin status via gcode - if (code_seen('S')) - { - int pin_status = code_value(); - int pin_number = LED_PIN; - if (code_seen('P') && pin_status >= 0 && pin_status <= 255) - pin_number = code_value(); - for(int8_t i = 0; i < (int8_t)sizeof(sensitive_pins); i++) - { - if (sensitive_pins[i] == pin_number) - { - pin_number = -1; - break; - } - } - if (pin_number > -1) - { - pinMode(pin_number, OUTPUT); - digitalWrite(pin_number, pin_status); - analogWrite(pin_number, pin_status); - } - } - break; - case 104: // M104 - if(setTargetedHotend(104)){ - break; - } - if (code_seen('S')) setTargetHotend(code_value(), tmp_extruder); - setWatch(); - break; - case 140: // M140 set bed temp - if (code_seen('S')) setTargetBed(code_value()); - break; - case 105 : // M105 - if(setTargetedHotend(105)){ - break; - } - #if (TEMP_0_PIN > -1) - SERIAL_PROTOCOLPGM("ok T:"); - SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); - SERIAL_PROTOCOLPGM(" /"); - SERIAL_PROTOCOL_F(degTargetHotend(tmp_extruder),1); - #if TEMP_BED_PIN > -1 - SERIAL_PROTOCOLPGM(" B:"); - SERIAL_PROTOCOL_F(degBed(),1); - SERIAL_PROTOCOLPGM(" /"); - SERIAL_PROTOCOL_F(degTargetBed(),1); - #endif //TEMP_BED_PIN - #else - SERIAL_ERROR_START; - SERIAL_ERRORLNPGM(MSG_ERR_NO_THERMISTORS); - #endif - - SERIAL_PROTOCOLPGM(" @:"); - SERIAL_PROTOCOL(getHeaterPower(tmp_extruder)); - - SERIAL_PROTOCOLPGM(" B@:"); - SERIAL_PROTOCOL(getHeaterPower(-1)); - - SERIAL_PROTOCOLLN(""); - return; - break; - case 109: - {// M109 - Wait for extruder heater to reach target. - if(setTargetedHotend(109)){ - break; - } - LCD_MESSAGEPGM(MSG_HEATING); - #ifdef AUTOTEMP - autotemp_enabled=false; - #endif - if (code_seen('S')) setTargetHotend(code_value(), tmp_extruder); - #ifdef AUTOTEMP - if (code_seen('S')) autotemp_min=code_value(); - if (code_seen('B')) autotemp_max=code_value(); - if (code_seen('F')) - { - autotemp_factor=code_value(); - autotemp_enabled=true; - } - #endif - - setWatch(); - codenum = millis(); - - /* See if we are heating up or cooling down */ - bool target_direction = isHeatingHotend(tmp_extruder); // true if heating, false if cooling - - #ifdef TEMP_RESIDENCY_TIME - long residencyStart; - residencyStart = -1; - /* continue to loop until we have reached the target temp - _and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */ - while((residencyStart == -1) || - (residencyStart >= 0 && (((unsigned int) (millis() - residencyStart)) < (TEMP_RESIDENCY_TIME * 1000UL))) ) { - #else - while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) { - #endif //TEMP_RESIDENCY_TIME - if( (millis() - codenum) > 1000UL ) - { //Print Temp Reading and remaining time every 1 second while heating up/cooling down - SERIAL_PROTOCOLPGM("T:"); - SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); - SERIAL_PROTOCOLPGM(" E:"); - SERIAL_PROTOCOL((int)tmp_extruder); - #ifdef TEMP_RESIDENCY_TIME - SERIAL_PROTOCOLPGM(" W:"); - if(residencyStart > -1) - { - codenum = ((TEMP_RESIDENCY_TIME * 1000UL) - (millis() - residencyStart)) / 1000UL; - SERIAL_PROTOCOLLN( codenum ); - } - else - { - SERIAL_PROTOCOLLN( "?" ); - } - #else - SERIAL_PROTOCOLLN(""); - #endif - codenum = millis(); - } - manage_heater(); - manage_inactivity(); - lcd_update(); - #ifdef TEMP_RESIDENCY_TIME - /* start/restart the TEMP_RESIDENCY_TIME timer whenever we reach target temp for the first time - or when current temp falls outside the hysteresis after target temp was reached */ - if ((residencyStart == -1 && target_direction && (degHotend(tmp_extruder) >= (degTargetHotend(tmp_extruder)-TEMP_WINDOW))) || - (residencyStart == -1 && !target_direction && (degHotend(tmp_extruder) <= (degTargetHotend(tmp_extruder)+TEMP_WINDOW))) || - (residencyStart > -1 && labs(degHotend(tmp_extruder) - degTargetHotend(tmp_extruder)) > TEMP_HYSTERESIS) ) - { - residencyStart = millis(); - } - #endif //TEMP_RESIDENCY_TIME - } - LCD_MESSAGEPGM(MSG_HEATING_COMPLETE); - starttime=millis(); - previous_millis_cmd = millis(); - } - break; - case 190: // M190 - Wait for bed heater to reach target. - #if TEMP_BED_PIN > -1 - LCD_MESSAGEPGM(MSG_BED_HEATING); - if (code_seen('S')) setTargetBed(code_value()); - codenum = millis(); - while(isHeatingBed()) - { - if(( millis() - codenum) > 1000 ) //Print Temp Reading every 1 second while heating up. - { - float tt=degHotend(active_extruder); - SERIAL_PROTOCOLPGM("T:"); - SERIAL_PROTOCOL(tt); - SERIAL_PROTOCOLPGM(" E:"); - SERIAL_PROTOCOL((int)active_extruder); - SERIAL_PROTOCOLPGM(" B:"); - SERIAL_PROTOCOL_F(degBed(),1); - SERIAL_PROTOCOLLN(""); - codenum = millis(); - } - manage_heater(); - manage_inactivity(); - lcd_update(); - } - LCD_MESSAGEPGM(MSG_BED_DONE); - previous_millis_cmd = millis(); - #endif - break; - - #if FAN_PIN > -1 - case 106: //M106 Fan On - if (code_seen('S')){ - fanSpeed=constrain(code_value(),0,255); - } - else { - fanSpeed=255; - } - break; - case 107: //M107 Fan Off - fanSpeed = 0; - break; - #endif //FAN_PIN - - #if (PS_ON_PIN > -1) - case 80: // M80 - ATX Power On - SET_OUTPUT(PS_ON_PIN); //GND - WRITE(PS_ON_PIN, PS_ON_AWAKE); - break; - #endif - - case 81: // M81 - ATX Power Off - - #if defined SUICIDE_PIN && SUICIDE_PIN > -1 - st_synchronize(); - suicide(); - #elif (PS_ON_PIN > -1) - SET_OUTPUT(PS_ON_PIN); - WRITE(PS_ON_PIN, PS_ON_ASLEEP); - #endif - break; - - case 82: - axis_relative_modes[3] = false; - break; - case 83: - axis_relative_modes[3] = true; - break; - case 18: //compatibility - case 84: // M84 - if(code_seen('S')){ - stepper_inactive_time = code_value() * 1000; - } - else - { - bool all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))|| (code_seen(axis_codes[3]))); - if(all_axis) - { - st_synchronize(); - disable_e0(); - disable_e1(); - disable_e2(); - finishAndDisableSteppers(); - } - else - { - st_synchronize(); - if(code_seen('X')) disable_x(); - if(code_seen('Y')) disable_y(); - if(code_seen('Z')) disable_z(); - #if ((E0_ENABLE_PIN != X_ENABLE_PIN) && (E1_ENABLE_PIN != Y_ENABLE_PIN)) // Only enable on boards that have seperate ENABLE_PINS - if(code_seen('E')) { - disable_e0(); - disable_e1(); - disable_e2(); - } - #endif - } - } - break; - case 85: // M85 - code_seen('S'); - max_inactive_time = code_value() * 1000; - break; - case 92: // M92 - for(int8_t i=0; i < NUM_AXIS; i++) - { - if(code_seen(axis_codes[i])) - { - if(i == 3) { // E - float value = code_value(); - if(value < 20.0) { - float factor = axis_steps_per_unit[i] / value; // increase e constants if M92 E14 is given for netfab. - max_e_jerk *= factor; - max_feedrate[i] *= factor; - axis_steps_per_sqr_second[i] *= factor; - } - axis_steps_per_unit[i] = value; - } - else { - axis_steps_per_unit[i] = code_value(); - } - } - } - break; - case 115: // M115 - SERIAL_PROTOCOLPGM(MSG_M115_REPORT); - break; - case 117: // M117 display message - starpos = (strchr(strchr_pointer + 5,'*')); - if(starpos!=NULL) - *(starpos-1)='\0'; - lcd_setstatus(strchr_pointer + 5); - break; - case 114: // M114 - SERIAL_PROTOCOLPGM("X:"); - SERIAL_PROTOCOL(current_position[X_AXIS]); - SERIAL_PROTOCOLPGM("Y:"); - SERIAL_PROTOCOL(current_position[Y_AXIS]); - SERIAL_PROTOCOLPGM("Z:"); - SERIAL_PROTOCOL(current_position[Z_AXIS]); - SERIAL_PROTOCOLPGM("E:"); - SERIAL_PROTOCOL(current_position[E_AXIS]); - - SERIAL_PROTOCOLPGM(MSG_COUNT_X); - SERIAL_PROTOCOL(float(st_get_position(X_AXIS))/axis_steps_per_unit[X_AXIS]); - SERIAL_PROTOCOLPGM("Y:"); - SERIAL_PROTOCOL(float(st_get_position(Y_AXIS))/axis_steps_per_unit[Y_AXIS]); - SERIAL_PROTOCOLPGM("Z:"); - SERIAL_PROTOCOL(float(st_get_position(Z_AXIS))/axis_steps_per_unit[Z_AXIS]); - - SERIAL_PROTOCOLLN(""); - break; - case 120: // M120 - enable_endstops(false) ; - break; - case 121: // M121 - enable_endstops(true) ; - break; - case 119: // M119 - SERIAL_PROTOCOLLN(MSG_M119_REPORT); - #if (X_MIN_PIN > -1) - SERIAL_PROTOCOLPGM(MSG_X_MIN); - SERIAL_PROTOCOLLN(((READ(X_MIN_PIN)^X_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); - #endif - #if (X_MAX_PIN > -1) - SERIAL_PROTOCOLPGM(MSG_X_MAX); - SERIAL_PROTOCOLLN(((READ(X_MAX_PIN)^X_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); - #endif - #if (Y_MIN_PIN > -1) - SERIAL_PROTOCOLPGM(MSG_Y_MIN); - SERIAL_PROTOCOLLN(((READ(Y_MIN_PIN)^Y_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); - #endif - #if (Y_MAX_PIN > -1) - SERIAL_PROTOCOLPGM(MSG_Y_MAX); - SERIAL_PROTOCOLLN(((READ(Y_MAX_PIN)^Y_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); - #endif - #if (Z_MIN_PIN > -1) - SERIAL_PROTOCOLPGM(MSG_Z_MIN); - SERIAL_PROTOCOLLN(((READ(Z_MIN_PIN)^Z_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); - #endif - #if (Z_MAX_PIN > -1) - SERIAL_PROTOCOLPGM(MSG_Z_MAX); - SERIAL_PROTOCOLLN(((READ(Z_MAX_PIN)^Z_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); - #endif - break; - //TODO: update for all axis, use for loop - case 201: // M201 - for(int8_t i=0; i < NUM_AXIS; i++) - { - if(code_seen(axis_codes[i])) - { - max_acceleration_units_per_sq_second[i] = code_value(); - axis_steps_per_sqr_second[i] = code_value() * axis_steps_per_unit[i]; - } - } - break; - #if 0 // Not used for Sprinter/grbl gen6 - case 202: // M202 - for(int8_t i=0; i < NUM_AXIS; i++) { - if(code_seen(axis_codes[i])) axis_travel_steps_per_sqr_second[i] = code_value() * axis_steps_per_unit[i]; - } - break; - #endif - case 203: // M203 max feedrate mm/sec - for(int8_t i=0; i < NUM_AXIS; i++) { - if(code_seen(axis_codes[i])) max_feedrate[i] = code_value(); - } - break; - case 204: // M204 acclereration S normal moves T filmanent only moves - { - if(code_seen('S')) acceleration = code_value() ; - if(code_seen('T')) retract_acceleration = code_value() ; - } - break; - case 205: //M205 advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk - { - if(code_seen('S')) minimumfeedrate = code_value(); - if(code_seen('T')) mintravelfeedrate = code_value(); - if(code_seen('B')) minsegmenttime = code_value() ; - if(code_seen('X')) max_xy_jerk = code_value() ; - if(code_seen('Z')) max_z_jerk = code_value() ; - if(code_seen('E')) max_e_jerk = code_value() ; - } - break; - case 206: // M206 additional homeing offset - for(int8_t i=0; i < 3; i++) - { - if(code_seen(axis_codes[i])) add_homeing[i] = code_value(); - } - break; - #ifdef FWRETRACT - case 207: //M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop] - { - if(code_seen('S')) - { - retract_length = code_value() ; - } - if(code_seen('F')) - { - retract_feedrate = code_value() ; - } - if(code_seen('Z')) - { - retract_zlift = code_value() ; - } - }break; - case 208: // M208 - set retract recover length S[positive mm surplus to the M207 S*] F[feedrate mm/sec] - { - if(code_seen('S')) - { - retract_recover_length = code_value() ; - } - if(code_seen('F')) - { - retract_recover_feedrate = code_value() ; - } - }break; - case 209: // M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. - { - if(code_seen('S')) - { - int t= code_value() ; - switch(t) - { - case 0: autoretract_enabled=false;retracted=false;break; - case 1: autoretract_enabled=true;retracted=false;break; - default: - SERIAL_ECHO_START; - SERIAL_ECHOPGM(MSG_UNKNOWN_COMMAND); - SERIAL_ECHO(cmdbuffer[bufindr]); - SERIAL_ECHOLNPGM("\""); - } - } - - }break; - #endif // FWRETRACT - #if EXTRUDERS > 1 - case 218: // M218 - set hotend offset (in mm), T X Y - { - if(setTargetedHotend(218)){ - break; - } - if(code_seen('X')) - { - extruder_offset[X_AXIS][tmp_extruder] = code_value(); - } - if(code_seen('Y')) - { - extruder_offset[Y_AXIS][tmp_extruder] = code_value(); - } - SERIAL_ECHO_START; - SERIAL_ECHOPGM(MSG_HOTEND_OFFSET); - for(tmp_extruder = 0; tmp_extruder < EXTRUDERS; tmp_extruder++) - { - SERIAL_ECHO(" "); - SERIAL_ECHO(extruder_offset[X_AXIS][tmp_extruder]); - SERIAL_ECHO(","); - SERIAL_ECHO(extruder_offset[Y_AXIS][tmp_extruder]); - } - SERIAL_ECHOLN(""); - }break; - #endif - case 220: // M220 S- set speed factor override percentage - { - if(code_seen('S')) - { - feedmultiply = code_value() ; - } - } - break; - case 221: // M221 S- set extrude factor override percentage - { - if(code_seen('S')) - { - extrudemultiply = code_value() ; - } - } - break; - - #ifdef PIDTEMP - case 301: // M301 - { - if(code_seen('P')) Kp = code_value(); - if(code_seen('I')) Ki = code_value()*PID_dT; - if(code_seen('D')) Kd = code_value()/PID_dT; - #ifdef PID_ADD_EXTRUSION_RATE - if(code_seen('C')) Kc = code_value(); - #endif - updatePID(); - SERIAL_PROTOCOL(MSG_OK); - SERIAL_PROTOCOL(" p:"); - SERIAL_PROTOCOL(Kp); - SERIAL_PROTOCOL(" i:"); - SERIAL_PROTOCOL(Ki/PID_dT); - SERIAL_PROTOCOL(" d:"); - SERIAL_PROTOCOL(Kd*PID_dT); - #ifdef PID_ADD_EXTRUSION_RATE - SERIAL_PROTOCOL(" c:"); - SERIAL_PROTOCOL(Kc*PID_dT); - #endif - SERIAL_PROTOCOLLN(""); - } - break; - #endif //PIDTEMP - #ifdef PIDTEMPBED - case 304: // M304 - { - if(code_seen('P')) bedKp = code_value(); - if(code_seen('I')) bedKi = code_value()*PID_dT; - if(code_seen('D')) bedKd = code_value()/PID_dT; - updatePID(); - SERIAL_PROTOCOL(MSG_OK); - SERIAL_PROTOCOL(" p:"); - SERIAL_PROTOCOL(bedKp); - SERIAL_PROTOCOL(" i:"); - SERIAL_PROTOCOL(bedKi/PID_dT); - SERIAL_PROTOCOL(" d:"); - SERIAL_PROTOCOL(bedKd*PID_dT); - SERIAL_PROTOCOLLN(""); - } - break; - #endif //PIDTEMP - case 240: // M240 Triggers a camera by emulating a Canon RC-1 : http://www.doc-diy.net/photo/rc-1_hacked/ - { - #ifdef PHOTOGRAPH_PIN - #if (PHOTOGRAPH_PIN > -1) - const uint8_t NUM_PULSES=16; - const float PULSE_LENGTH=0.01524; - for(int i=0; i < NUM_PULSES; i++) { - WRITE(PHOTOGRAPH_PIN, HIGH); - _delay_ms(PULSE_LENGTH); - WRITE(PHOTOGRAPH_PIN, LOW); - _delay_ms(PULSE_LENGTH); - } - delay(7.33); - for(int i=0; i < NUM_PULSES; i++) { - WRITE(PHOTOGRAPH_PIN, HIGH); - _delay_ms(PULSE_LENGTH); - WRITE(PHOTOGRAPH_PIN, LOW); - _delay_ms(PULSE_LENGTH); - } - #endif - #endif - } - break; - - case 302: // allow cold extrudes - { - allow_cold_extrudes(true); - } - break; - case 303: // M303 PID autotune - { - float temp = 150.0; - int e=0; - int c=5; - if (code_seen('E')) e=code_value(); - if (e<0) - temp=70; - if (code_seen('S')) temp=code_value(); - if (code_seen('C')) c=code_value(); - PID_autotune(temp, e, c); - } - break; - case 400: // M400 finish all moves - { - st_synchronize(); - } - break; - case 500: // M500 Store settings in EEPROM - { - Config_StoreSettings(); - } - break; - case 501: // M501 Read settings from EEPROM - { - Config_RetrieveSettings(); - } - break; - case 502: // M502 Revert to default settings - { - Config_ResetDefault(); - } - break; - case 503: // M503 print settings currently in memory - { - Config_PrintSettings(); - } - break; - #ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED - case 540: - { - if(code_seen('S')) abort_on_endstop_hit = code_value() > 0; - } - break; - #endif - #ifdef FILAMENTCHANGEENABLE - case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] - { - float target[4]; - float lastpos[4]; - target[X_AXIS]=current_position[X_AXIS]; - target[Y_AXIS]=current_position[Y_AXIS]; - target[Z_AXIS]=current_position[Z_AXIS]; - target[E_AXIS]=current_position[E_AXIS]; - lastpos[X_AXIS]=current_position[X_AXIS]; - lastpos[Y_AXIS]=current_position[Y_AXIS]; - lastpos[Z_AXIS]=current_position[Z_AXIS]; - lastpos[E_AXIS]=current_position[E_AXIS]; - //retract by E - if(code_seen('E')) - { - target[E_AXIS]+= code_value(); - } - else - { - #ifdef FILAMENTCHANGE_FIRSTRETRACT - target[E_AXIS]+= FILAMENTCHANGE_FIRSTRETRACT ; - #endif - } - plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); - - //lift Z - if(code_seen('Z')) - { - target[Z_AXIS]+= code_value(); - } - else - { - #ifdef FILAMENTCHANGE_ZADD - target[Z_AXIS]+= FILAMENTCHANGE_ZADD ; - #endif - } - plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); - - //move xy - if(code_seen('X')) - { - target[X_AXIS]+= code_value(); - } - else - { - #ifdef FILAMENTCHANGE_XPOS - target[X_AXIS]= FILAMENTCHANGE_XPOS ; - #endif - } - if(code_seen('Y')) - { - target[Y_AXIS]= code_value(); - } - else - { - #ifdef FILAMENTCHANGE_YPOS - target[Y_AXIS]= FILAMENTCHANGE_YPOS ; - #endif - } - - plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); - - if(code_seen('L')) - { - target[E_AXIS]+= code_value(); - } - else - { - #ifdef FILAMENTCHANGE_FINALRETRACT - target[E_AXIS]+= FILAMENTCHANGE_FINALRETRACT ; - #endif - } - - plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); - - //finish moves - st_synchronize(); - //disable extruder steppers so filament can be removed - disable_e0(); - disable_e1(); - disable_e2(); - delay(100); - LCD_ALERTMESSAGEPGM(MSG_FILAMENTCHANGE); - uint8_t cnt=0; - while(!LCD_CLICKED){ - cnt++; - manage_heater(); - manage_inactivity(); - lcd_update(); - - #if BEEPER > -1 - if(cnt==0) - { - SET_OUTPUT(BEEPER); - - WRITE(BEEPER,HIGH); - delay(3); - WRITE(BEEPER,LOW); - delay(3); - } - #endif - } - - //return to normal - if(code_seen('L')) - { - target[E_AXIS]+= -code_value(); - } - else - { - #ifdef FILAMENTCHANGE_FINALRETRACT - target[E_AXIS]+=(-1)*FILAMENTCHANGE_FINALRETRACT ; - #endif - } - current_position[E_AXIS]=target[E_AXIS]; //the long retract of L is compensated by manual filament feeding - plan_set_e_position(current_position[E_AXIS]); - plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); //should do nothing - plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); //move xy back - plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], lastpos[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); //move z back - plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], lastpos[Z_AXIS], lastpos[E_AXIS], feedrate/60, active_extruder); //final untretract - } - break; - #endif //FILAMENTCHANGEENABLE - case 907: // M907 Set digital trimpot motor current using axis codes. - { - #if DIGIPOTSS_PIN > -1 - for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) digipot_current(i,code_value()); - if(code_seen('B')) digipot_current(4,code_value()); - if(code_seen('S')) for(int i=0;i<=4;i++) digipot_current(i,code_value()); - #endif - } - case 908: // M908 Control digital trimpot directly. - { - #if DIGIPOTSS_PIN > -1 - uint8_t channel,current; - if(code_seen('P')) channel=code_value(); - if(code_seen('S')) current=code_value(); - digitalPotWrite(channel, current); - #endif - } - break; - case 350: // M350 Set microstepping mode. Warning: Steps per unit remains unchanged. S code sets stepping mode for all drivers. - { - #if X_MS1_PIN > -1 - if(code_seen('S')) for(int i=0;i<=4;i++) microstep_mode(i,code_value()); - for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) microstep_mode(i,(uint8_t)code_value()); - if(code_seen('B')) microstep_mode(4,code_value()); - microstep_readings(); - #endif - } - break; - case 351: // M351 Toggle MS1 MS2 pins directly, S# determines MS1 or MS2, X# sets the pin high/low. - { - #if X_MS1_PIN > -1 - if(code_seen('S')) switch((int)code_value()) - { - case 1: - for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) microstep_ms(i,code_value(),-1); - if(code_seen('B')) microstep_ms(4,code_value(),-1); - break; - case 2: - for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) microstep_ms(i,-1,code_value()); - if(code_seen('B')) microstep_ms(4,-1,code_value()); - break; - } - microstep_readings(); - #endif - } - break; - case 999: // M999: Restart after being stopped - Stopped = false; - lcd_reset_alert_level(); - gcode_LastN = Stopped_gcode_LastN; - FlushSerialRequestResend(); - break; - } - } - - else if(code_seen('T')) - { - tmp_extruder = code_value(); - if(tmp_extruder >= EXTRUDERS) { - SERIAL_ECHO_START; - SERIAL_ECHO("T"); - SERIAL_ECHO(tmp_extruder); - SERIAL_ECHOLN(MSG_INVALID_EXTRUDER); - } - else { - boolean make_move = false; - if(code_seen('F')) { - make_move = true; - next_feedrate = code_value(); - if(next_feedrate > 0.0) { - feedrate = next_feedrate; - } - } - #if EXTRUDERS > 1 - if(tmp_extruder != active_extruder) { - // Save current position to return to after applying extruder offset - memcpy(destination, current_position, sizeof(destination)); - // Offset extruder (only by XY) - int i; - for(i = 0; i < 2; i++) { - current_position[i] = current_position[i] - - extruder_offset[i][active_extruder] + - extruder_offset[i][tmp_extruder]; - } - // Set the new active extruder and position - active_extruder = tmp_extruder; - plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); - // Move to the old position if 'F' was in the parameters - if(make_move && Stopped == false) { - prepare_move(); - } +#endif +uint8_t active_extruder = 0; +int fanSpeed=0; + +#ifdef FWRETRACT + bool autoretract_enabled=true; + bool retracted=false; + float retract_length=3, retract_feedrate=17*60, retract_zlift=0.8; + float retract_recover_length=0, retract_recover_feedrate=8*60; +#endif + +//=========================================================================== +//=============================private variables============================= +//=========================================================================== +const char axis_codes[NUM_AXIS] = {'X', 'Y', 'Z', 'E'}; +static float destination[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0}; +static float offset[3] = {0.0, 0.0, 0.0}; +static bool home_all_axis = true; +static float feedrate = 1500.0, next_feedrate, saved_feedrate; +static long gcode_N, gcode_LastN, Stopped_gcode_LastN = 0; + +static bool relative_mode = false; //Determines Absolute or Relative Coordinates + +static char cmdbuffer[BUFSIZE][MAX_CMD_SIZE]; +static bool fromsd[BUFSIZE]; +static int bufindr = 0; +static int bufindw = 0; +static int buflen = 0; +//static int i = 0; +static char serial_char; +static int serial_count = 0; +static boolean comment_mode = false; +static char *strchr_pointer; // just a pointer to find chars in the cmd string like X, Y, Z, E, etc + +const int sensitive_pins[] = SENSITIVE_PINS; // Sensitive pin list for M42 + +//static float tt = 0; +//static float bt = 0; + +//Inactivity shutdown variables +static unsigned long previous_millis_cmd = 0; +static unsigned long max_inactive_time = 0; +static unsigned long stepper_inactive_time = DEFAULT_STEPPER_DEACTIVE_TIME*1000l; + +unsigned long starttime=0; +unsigned long stoptime=0; + +static uint8_t tmp_extruder; + + +bool Stopped=false; + +//=========================================================================== +//=============================ROUTINES============================= +//=========================================================================== + +void get_arc_coordinates(); +bool setTargetedHotend(int code); + +void serial_echopair_P(const char *s_P, float v) + { serialprintPGM(s_P); SERIAL_ECHO(v); } +void serial_echopair_P(const char *s_P, double v) + { serialprintPGM(s_P); SERIAL_ECHO(v); } +void serial_echopair_P(const char *s_P, unsigned long v) + { serialprintPGM(s_P); SERIAL_ECHO(v); } + +extern "C"{ + extern unsigned int __bss_end; + extern unsigned int __heap_start; + extern void *__brkval; + + int freeMemory() { + int free_memory; + + if((int)__brkval == 0) + free_memory = ((int)&free_memory) - ((int)&__bss_end); + else + free_memory = ((int)&free_memory) - ((int)__brkval); + + return free_memory; + } +} + +//adds an command to the main command buffer +//thats really done in a non-safe way. +//needs overworking someday +void enquecommand(const char *cmd) +{ + if(buflen < BUFSIZE) + { + //this is dangerous if a mixing of serial and this happsens + strcpy(&(cmdbuffer[bufindw][0]),cmd); + SERIAL_ECHO_START; + SERIAL_ECHOPGM("enqueing \""); + SERIAL_ECHO(cmdbuffer[bufindw]); + SERIAL_ECHOLNPGM("\""); + bufindw= (bufindw + 1)%BUFSIZE; + buflen += 1; + } +} + +void enquecommand_P(const char *cmd) +{ + if(buflen < BUFSIZE) + { + //this is dangerous if a mixing of serial and this happsens + strcpy_P(&(cmdbuffer[bufindw][0]),cmd); + SERIAL_ECHO_START; + SERIAL_ECHOPGM("enqueing \""); + SERIAL_ECHO(cmdbuffer[bufindw]); + SERIAL_ECHOLNPGM("\""); + bufindw= (bufindw + 1)%BUFSIZE; + buflen += 1; + } +} + +void setup_killpin() +{ + #if( KILL_PIN>-1 ) + pinMode(KILL_PIN,INPUT); + WRITE(KILL_PIN,HIGH); + #endif +} + +void setup_photpin() +{ + #ifdef PHOTOGRAPH_PIN + #if (PHOTOGRAPH_PIN > -1) + SET_OUTPUT(PHOTOGRAPH_PIN); + WRITE(PHOTOGRAPH_PIN, LOW); + #endif + #endif +} + +void setup_powerhold() +{ + #ifdef SUICIDE_PIN + #if (SUICIDE_PIN> -1) + SET_OUTPUT(SUICIDE_PIN); + WRITE(SUICIDE_PIN, HIGH); + #endif + #endif + #if (PS_ON_PIN > -1) + SET_OUTPUT(PS_ON_PIN); + WRITE(PS_ON_PIN, PS_ON_AWAKE); + #endif +} + +void suicide() +{ + #ifdef SUICIDE_PIN + #if (SUICIDE_PIN> -1) + SET_OUTPUT(SUICIDE_PIN); + WRITE(SUICIDE_PIN, LOW); + #endif + #endif +} + +void setup() +{ + setup_killpin(); + setup_powerhold(); + MYSERIAL.begin(BAUDRATE); + SERIAL_PROTOCOLLNPGM("start"); + SERIAL_ECHO_START; + + // Check startup - does nothing if bootloader sets MCUSR to 0 + byte mcu = MCUSR; + if(mcu & 1) SERIAL_ECHOLNPGM(MSG_POWERUP); + if(mcu & 2) SERIAL_ECHOLNPGM(MSG_EXTERNAL_RESET); + if(mcu & 4) SERIAL_ECHOLNPGM(MSG_BROWNOUT_RESET); + if(mcu & 8) SERIAL_ECHOLNPGM(MSG_WATCHDOG_RESET); + if(mcu & 32) SERIAL_ECHOLNPGM(MSG_SOFTWARE_RESET); + MCUSR=0; + + SERIAL_ECHOPGM(MSG_MARLIN); + SERIAL_ECHOLNPGM(VERSION_STRING); + #ifdef STRING_VERSION_CONFIG_H + #ifdef STRING_CONFIG_H_AUTHOR + SERIAL_ECHO_START; + SERIAL_ECHOPGM(MSG_CONFIGURATION_VER); + SERIAL_ECHOPGM(STRING_VERSION_CONFIG_H); + SERIAL_ECHOPGM(MSG_AUTHOR); + SERIAL_ECHOLNPGM(STRING_CONFIG_H_AUTHOR); + SERIAL_ECHOPGM("Compiled: "); + SERIAL_ECHOLNPGM(__DATE__); + #endif + #endif + SERIAL_ECHO_START; + SERIAL_ECHOPGM(MSG_FREE_MEMORY); + SERIAL_ECHO(freeMemory()); + SERIAL_ECHOPGM(MSG_PLANNER_BUFFER_BYTES); + SERIAL_ECHOLN((int)sizeof(block_t)*BLOCK_BUFFER_SIZE); + for(int8_t i = 0; i < BUFSIZE; i++) + { + fromsd[i] = false; + } + + Config_RetrieveSettings(); // loads data from EEPROM if available + + for(int8_t i=0; i < NUM_AXIS; i++) + { + axis_steps_per_sqr_second[i] = max_acceleration_units_per_sq_second[i] * axis_steps_per_unit[i]; + } + + + tp_init(); // Initialize temperature loop + plan_init(); // Initialize planner; + watchdog_init(); + st_init(); // Initialize stepper, this enables interrupts! + setup_photpin(); + + lcd_init(); + + #ifdef CONTROLLERFAN_PIN + SET_OUTPUT(CONTROLLERFAN_PIN); //Set pin used for driver cooling fan + #endif + + #ifdef EXTRUDERFAN_PIN + SET_OUTPUT(EXTRUDERFAN_PIN); //Set pin used for extruder cooling fan + #endif +} + + +void loop() +{ + if(buflen < (BUFSIZE-1)) + get_command(); + #ifdef SDSUPPORT + card.checkautostart(false); + #endif + if(buflen) + { + #ifdef SDSUPPORT + if(card.saving) + { + if(strstr_P(cmdbuffer[bufindr], PSTR("M29")) == NULL) + { + card.write_command(cmdbuffer[bufindr]); + SERIAL_PROTOCOLLNPGM(MSG_OK); + } + else + { + card.closefile(); + SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED); + } } - #endif - SERIAL_ECHO_START; - SERIAL_ECHO(MSG_ACTIVE_EXTRUDER); - SERIAL_PROTOCOLLN((int)active_extruder); - } - } - - else - { - SERIAL_ECHO_START; - SERIAL_ECHOPGM(MSG_UNKNOWN_COMMAND); - SERIAL_ECHO(cmdbuffer[bufindr]); - SERIAL_ECHOLNPGM("\""); - } - - ClearToSend(); -} - -void FlushSerialRequestResend() -{ - //char cmdbuffer[bufindr][100]="Resend:"; - MYSERIAL.flush(); - SERIAL_PROTOCOLPGM(MSG_RESEND); - SERIAL_PROTOCOLLN(gcode_LastN + 1); - ClearToSend(); -} - -void ClearToSend() -{ - previous_millis_cmd = millis(); - #ifdef SDSUPPORT - if(fromsd[bufindr]) - return; - #endif //SDSUPPORT - SERIAL_PROTOCOLLNPGM(MSG_OK); -} - -void get_coordinates() -{ - bool seen[4]={false,false,false,false}; - for(int8_t i=0; i < NUM_AXIS; i++) { - if(code_seen(axis_codes[i])) - { - destination[i] = (float)code_value() + (axis_relative_modes[i] || relative_mode)*current_position[i]; - seen[i]=true; - } - else destination[i] = current_position[i]; //Are these else lines really needed? - } - if(code_seen('F')) { - next_feedrate = code_value(); - if(next_feedrate > 0.0) feedrate = next_feedrate; - } - #ifdef FWRETRACT - if(autoretract_enabled) - if( !(seen[X_AXIS] || seen[Y_AXIS] || seen[Z_AXIS]) && seen[E_AXIS]) - { - float echange=destination[E_AXIS]-current_position[E_AXIS]; - if(echange<-MIN_RETRACT) //retract - { - if(!retracted) - { - - destination[Z_AXIS]+=retract_zlift; //not sure why chaninging current_position negatively does not work. - //if slicer retracted by echange=-1mm and you want to retract 3mm, corrrectede=-2mm additionally - float correctede=-echange-retract_length; - //to generate the additional steps, not the destination is changed, but inversely the current position - current_position[E_AXIS]+=-correctede; - feedrate=retract_feedrate; - retracted=true; - } - - } - else - if(echange>MIN_RETRACT) //retract_recover - { - if(retracted) - { - //current_position[Z_AXIS]+=-retract_zlift; - //if slicer retracted_recovered by echange=+1mm and you want to retract_recover 3mm, corrrectede=2mm additionally - float correctede=-echange+1*retract_length+retract_recover_length; //total unretract=retract_length+retract_recover_length[surplus] - current_position[E_AXIS]+=correctede; //to generate the additional steps, not the destination is changed, but inversely the current position - feedrate=retract_recover_feedrate; - retracted=false; - } - } - - } - #endif //FWRETRACT -} - -void get_arc_coordinates() -{ -#ifdef SF_ARC_FIX - bool relative_mode_backup = relative_mode; - relative_mode = true; -#endif - get_coordinates(); -#ifdef SF_ARC_FIX - relative_mode=relative_mode_backup; -#endif - - if(code_seen('I')) { - offset[0] = code_value(); - } - else { - offset[0] = 0.0; - } - if(code_seen('J')) { - offset[1] = code_value(); - } - else { - offset[1] = 0.0; - } -} - -void clamp_to_software_endstops(float target[3]) -{ - if (min_software_endstops) { - if (target[X_AXIS] < min_pos[X_AXIS]) target[X_AXIS] = min_pos[X_AXIS]; - if (target[Y_AXIS] < min_pos[Y_AXIS]) target[Y_AXIS] = min_pos[Y_AXIS]; - if (target[Z_AXIS] < min_pos[Z_AXIS]) target[Z_AXIS] = min_pos[Z_AXIS]; - } - - if (max_software_endstops) { - if (target[X_AXIS] > max_pos[X_AXIS]) target[X_AXIS] = max_pos[X_AXIS]; - if (target[Y_AXIS] > max_pos[Y_AXIS]) target[Y_AXIS] = max_pos[Y_AXIS]; - if (target[Z_AXIS] > max_pos[Z_AXIS]) target[Z_AXIS] = max_pos[Z_AXIS]; - } -} - -void prepare_move() -{ - clamp_to_software_endstops(destination); - - previous_millis_cmd = millis(); - // Do not use feedmultiply for E or Z only moves - if( (current_position[X_AXIS] == destination [X_AXIS]) && (current_position[Y_AXIS] == destination [Y_AXIS])) { - plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); - } - else { - plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate*feedmultiply/60/100.0, active_extruder); - } - for(int8_t i=0; i < NUM_AXIS; i++) { - current_position[i] = destination[i]; - } -} - -void prepare_arc_move(char isclockwise) { - float r = hypot(offset[X_AXIS], offset[Y_AXIS]); // Compute arc radius for mc_arc - - // Trace the arc - mc_arc(current_position, destination, offset, X_AXIS, Y_AXIS, Z_AXIS, feedrate*feedmultiply/60/100.0, r, isclockwise, active_extruder); - - // As far as the parser is concerned, the position is now == target. In reality the - // motion control system might still be processing the action and the real tool position - // in any intermediate location. - for(int8_t i=0; i < NUM_AXIS; i++) { - current_position[i] = destination[i]; - } - previous_millis_cmd = millis(); -} - -#ifdef CONTROLLERFAN_PIN -unsigned long lastMotor = 0; //Save the time for when a motor was turned on last -unsigned long lastMotorCheck = 0; - -void controllerFan() -{ - if ((millis() - lastMotorCheck) >= 2500) //Not a time critical function, so we only check every 2500ms - { - lastMotorCheck = millis(); - - if(!READ(X_ENABLE_PIN) || !READ(Y_ENABLE_PIN) || !READ(Z_ENABLE_PIN) - #if EXTRUDERS > 2 - || !READ(E2_ENABLE_PIN) - #endif - #if EXTRUDER > 1 - || !READ(E2_ENABLE_PIN) - #endif - || !READ(E0_ENABLE_PIN)) //If any of the drivers are enabled... - { - lastMotor = millis(); //... set time to NOW so the fan will turn on - } - - if ((millis() - lastMotor) >= (CONTROLLERFAN_SEC*1000UL) || lastMotor == 0) //If the last time any driver was enabled, is longer since than CONTROLLERSEC... - { - WRITE(CONTROLLERFAN_PIN, LOW); //... turn the fan off - } - else - { - WRITE(CONTROLLERFAN_PIN, HIGH); //... turn the fan on - } - } -} -#endif - -void manage_inactivity() -{ - if( (millis() - previous_millis_cmd) > max_inactive_time ) - if(max_inactive_time) - kill(); - if(stepper_inactive_time) { - if( (millis() - previous_millis_cmd) > stepper_inactive_time ) - { - if(blocks_queued() == false) { - disable_x(); - disable_y(); - disable_z(); - disable_e0(); - disable_e1(); - disable_e2(); - } - } - } - #if( KILL_PIN>-1 ) - if( 0 == READ(KILL_PIN) ) - kill(); - #endif - #ifdef CONTROLLERFAN_PIN - controllerFan(); //Check if fan should be turned on to cool stepper drivers down - #endif - #ifdef EXTRUDER_RUNOUT_PREVENT - if( (millis() - previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 ) - if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP) - { - bool oldstatus=READ(E0_ENABLE_PIN); - enable_e0(); - float oldepos=current_position[E_AXIS]; - float oldedes=destination[E_AXIS]; - plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], - current_position[E_AXIS]+EXTRUDER_RUNOUT_EXTRUDE*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS], - EXTRUDER_RUNOUT_SPEED/60.*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS], active_extruder); - current_position[E_AXIS]=oldepos; - destination[E_AXIS]=oldedes; - plan_set_e_position(oldepos); - previous_millis_cmd=millis(); - st_synchronize(); - WRITE(E0_ENABLE_PIN,oldstatus); - } - #endif - check_axes_activity(); -} - -void kill() -{ - cli(); // Stop interrupts - disable_heater(); - - disable_x(); - disable_y(); - disable_z(); - disable_e0(); - disable_e1(); - disable_e2(); - - if(PS_ON_PIN > -1) pinMode(PS_ON_PIN,INPUT); - SERIAL_ERROR_START; - SERIAL_ERRORLNPGM(MSG_ERR_KILLED); - LCD_ALERTMESSAGEPGM(MSG_KILLED); - suicide(); - while(1) { /* Intentionally left empty */ } // Wait for reset -} - -void Stop() -{ - disable_heater(); - if(Stopped == false) { - Stopped = true; - Stopped_gcode_LastN = gcode_LastN; // Save last g_code for restart - SERIAL_ERROR_START; - SERIAL_ERRORLNPGM(MSG_ERR_STOPPED); - LCD_MESSAGEPGM(MSG_STOPPED); - } -} - -bool IsStopped() { return Stopped; }; - -#ifdef FAST_PWM_FAN -void setPwmFrequency(uint8_t pin, int val) -{ - val &= 0x07; - switch(digitalPinToTimer(pin)) - { - - #if defined(TCCR0A) - case TIMER0A: - case TIMER0B: -// TCCR0B &= ~(_BV(CS00) | _BV(CS01) | _BV(CS02)); -// TCCR0B |= val; - break; - #endif - - #if defined(TCCR1A) - case TIMER1A: - case TIMER1B: -// TCCR1B &= ~(_BV(CS10) | _BV(CS11) | _BV(CS12)); -// TCCR1B |= val; - break; - #endif - - #if defined(TCCR2) - case TIMER2: - case TIMER2: - TCCR2 &= ~(_BV(CS10) | _BV(CS11) | _BV(CS12)); - TCCR2 |= val; - break; - #endif - - #if defined(TCCR2A) - case TIMER2A: - case TIMER2B: - TCCR2B &= ~(_BV(CS20) | _BV(CS21) | _BV(CS22)); - TCCR2B |= val; - break; - #endif - - #if defined(TCCR3A) - case TIMER3A: - case TIMER3B: - case TIMER3C: - TCCR3B &= ~(_BV(CS30) | _BV(CS31) | _BV(CS32)); - TCCR3B |= val; - break; - #endif - - #if defined(TCCR4A) - case TIMER4A: - case TIMER4B: - case TIMER4C: - TCCR4B &= ~(_BV(CS40) | _BV(CS41) | _BV(CS42)); - TCCR4B |= val; - break; - #endif - - #if defined(TCCR5A) - case TIMER5A: - case TIMER5B: - case TIMER5C: - TCCR5B &= ~(_BV(CS50) | _BV(CS51) | _BV(CS52)); - TCCR5B |= val; - break; - #endif - - } -} -#endif //FAST_PWM_FAN - -bool setTargetedHotend(int code){ - tmp_extruder = active_extruder; - if(code_seen('T')) { - tmp_extruder = code_value(); - if(tmp_extruder >= EXTRUDERS) { - SERIAL_ECHO_START; - switch(code){ - case 104: - SERIAL_ECHO(MSG_M104_INVALID_EXTRUDER); - break; - case 105: - SERIAL_ECHO(MSG_M105_INVALID_EXTRUDER); - break; - case 109: - SERIAL_ECHO(MSG_M109_INVALID_EXTRUDER); - break; - case 218: - SERIAL_ECHO(MSG_M218_INVALID_EXTRUDER); - break; - } - SERIAL_ECHOLN(tmp_extruder); - return true; - } - } - return false; + else + { + process_commands(); + } + #else + process_commands(); + #endif //SDSUPPORT + buflen = (buflen-1); + bufindr = (bufindr + 1)%BUFSIZE; + } + //check heater every n milliseconds + manage_heater(); + manage_inactivity(); + checkHitEndstops(); + lcd_update(); +} + +void get_command() +{ + while( MYSERIAL.available() > 0 && buflen < BUFSIZE) { + serial_char = MYSERIAL.read(); + if(serial_char == '\n' || + serial_char == '\r' || + (serial_char == ':' && comment_mode == false) || + serial_count >= (MAX_CMD_SIZE - 1) ) + { + if(!serial_count) { //if empty line + comment_mode = false; //for new command + return; + } + cmdbuffer[bufindw][serial_count] = 0; //terminate string + if(!comment_mode){ + comment_mode = false; //for new command + fromsd[bufindw] = false; + if(strchr(cmdbuffer[bufindw], 'N') != NULL) + { + strchr_pointer = strchr(cmdbuffer[bufindw], 'N'); + gcode_N = (strtol(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL, 10)); + if(gcode_N != gcode_LastN+1 && (strstr_P(cmdbuffer[bufindw], PSTR("M110")) == NULL) ) { + SERIAL_ERROR_START; + SERIAL_ERRORPGM(MSG_ERR_LINE_NO); + SERIAL_ERRORLN(gcode_LastN); + //Serial.println(gcode_N); + FlushSerialRequestResend(); + serial_count = 0; + return; + } + + if(strchr(cmdbuffer[bufindw], '*') != NULL) + { + byte checksum = 0; + byte count = 0; + while(cmdbuffer[bufindw][count] != '*') checksum = checksum^cmdbuffer[bufindw][count++]; + strchr_pointer = strchr(cmdbuffer[bufindw], '*'); + + if( (int)(strtod(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL)) != checksum) { + SERIAL_ERROR_START; + SERIAL_ERRORPGM(MSG_ERR_CHECKSUM_MISMATCH); + SERIAL_ERRORLN(gcode_LastN); + FlushSerialRequestResend(); + serial_count = 0; + return; + } + //if no errors, continue parsing + } + else + { + SERIAL_ERROR_START; + SERIAL_ERRORPGM(MSG_ERR_NO_CHECKSUM); + SERIAL_ERRORLN(gcode_LastN); + FlushSerialRequestResend(); + serial_count = 0; + return; + } + + gcode_LastN = gcode_N; + //if no errors, continue parsing + } + else // if we don't receive 'N' but still see '*' + { + if((strchr(cmdbuffer[bufindw], '*') != NULL)) + { + SERIAL_ERROR_START; + SERIAL_ERRORPGM(MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM); + SERIAL_ERRORLN(gcode_LastN); + serial_count = 0; + return; + } + } + if((strchr(cmdbuffer[bufindw], 'G') != NULL)){ + strchr_pointer = strchr(cmdbuffer[bufindw], 'G'); + switch((int)((strtod(&cmdbuffer[bufindw][strchr_pointer - cmdbuffer[bufindw] + 1], NULL)))){ + case 0: + case 1: + case 2: + case 3: + if(Stopped == false) { // If printer is stopped by an error the G[0-3] codes are ignored. + #ifdef SDSUPPORT + if(card.saving) + break; + #endif //SDSUPPORT + SERIAL_PROTOCOLLNPGM(MSG_OK); + } + else { + SERIAL_ERRORLNPGM(MSG_ERR_STOPPED); + LCD_MESSAGEPGM(MSG_STOPPED); + } + break; + default: + break; + } + + } + bufindw = (bufindw + 1)%BUFSIZE; + buflen += 1; + } + serial_count = 0; //clear buffer + } + else + { + if(serial_char == ';') comment_mode = true; + if(!comment_mode) cmdbuffer[bufindw][serial_count++] = serial_char; + } + } + #ifdef SDSUPPORT + if(!card.sdprinting || serial_count!=0){ + return; + } + while( !card.eof() && buflen < BUFSIZE) { + int16_t n=card.get(); + serial_char = (char)n; + if(serial_char == '\n' || + serial_char == '\r' || + (serial_char == ':' && comment_mode == false) || + serial_count >= (MAX_CMD_SIZE - 1)||n==-1) + { + if(card.eof()){ + SERIAL_PROTOCOLLNPGM(MSG_FILE_PRINTED); + stoptime=millis(); + char time[30]; + unsigned long t=(stoptime-starttime)/1000; + int hours, minutes; + minutes=(t/60)%60; + hours=t/60/60; + sprintf_P(time, PSTR("%i hours %i minutes"),hours, minutes); + SERIAL_ECHO_START; + SERIAL_ECHOLN(time); + lcd_setstatus(time); + card.printingHasFinished(); + card.checkautostart(true); + + } + if(!serial_count) + { + comment_mode = false; //for new command + return; //if empty line + } + cmdbuffer[bufindw][serial_count] = 0; //terminate string +// if(!comment_mode){ + fromsd[bufindw] = true; + buflen += 1; + bufindw = (bufindw + 1)%BUFSIZE; +// } + comment_mode = false; //for new command + serial_count = 0; //clear buffer + } + else + { + if(serial_char == ';') comment_mode = true; + if(!comment_mode) cmdbuffer[bufindw][serial_count++] = serial_char; + } + } + + #endif //SDSUPPORT + +} + + +float code_value() +{ + return (strtod(&cmdbuffer[bufindr][strchr_pointer - cmdbuffer[bufindr] + 1], NULL)); +} + +long code_value_long() +{ + return (strtol(&cmdbuffer[bufindr][strchr_pointer - cmdbuffer[bufindr] + 1], NULL, 10)); +} + +bool code_seen(char code) +{ + strchr_pointer = strchr(cmdbuffer[bufindr], code); + return (strchr_pointer != NULL); //Return True if a character was found +} + +#define DEFINE_PGM_READ_ANY(type, reader) \ + static inline type pgm_read_any(const type *p) \ + { return pgm_read_##reader##_near(p); } + +DEFINE_PGM_READ_ANY(float, float); +DEFINE_PGM_READ_ANY(signed char, byte); + +#define XYZ_CONSTS_FROM_CONFIG(type, array, CONFIG) \ +static const PROGMEM type array##_P[3] = \ + { X_##CONFIG, Y_##CONFIG, Z_##CONFIG }; \ +static inline type array(int axis) \ + { return pgm_read_any(&array##_P[axis]); } + +XYZ_CONSTS_FROM_CONFIG(float, base_min_pos, MIN_POS); +XYZ_CONSTS_FROM_CONFIG(float, base_max_pos, MAX_POS); +XYZ_CONSTS_FROM_CONFIG(float, base_home_pos, HOME_POS); +XYZ_CONSTS_FROM_CONFIG(float, max_length, MAX_LENGTH); +XYZ_CONSTS_FROM_CONFIG(float, home_retract_mm, HOME_RETRACT_MM); +XYZ_CONSTS_FROM_CONFIG(signed char, home_dir, HOME_DIR); + +static void axis_is_at_home(int axis) { + current_position[axis] = base_home_pos(axis) + add_homeing[axis]; + min_pos[axis] = base_min_pos(axis) + add_homeing[axis]; + max_pos[axis] = base_max_pos(axis) + add_homeing[axis]; +} + +static void homeaxis(int axis) { +#define HOMEAXIS_DO(LETTER) \ + ((LETTER##_MIN_PIN > -1 && LETTER##_HOME_DIR==-1) || (LETTER##_MAX_PIN > -1 && LETTER##_HOME_DIR==1)) + + if (axis==X_AXIS ? HOMEAXIS_DO(X) : + axis==Y_AXIS ? HOMEAXIS_DO(Y) : + axis==Z_AXIS ? HOMEAXIS_DO(Z) : + 0) { + current_position[axis] = 0; + plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); + destination[axis] = 1.5 * max_length(axis) * home_dir(axis); + feedrate = homing_feedrate[axis]; + plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); + st_synchronize(); + + current_position[axis] = 0; + plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); + destination[axis] = -home_retract_mm(axis) * home_dir(axis); + plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); + st_synchronize(); + + destination[axis] = 2*home_retract_mm(axis) * home_dir(axis); + feedrate = homing_feedrate[axis]/2 ; + plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); + st_synchronize(); + + axis_is_at_home(axis); + destination[axis] = current_position[axis]; + feedrate = 0.0; + endstops_hit_on_purpose(); + } +} +#define HOMEAXIS(LETTER) homeaxis(LETTER##_AXIS) + +void process_commands() +{ + unsigned long codenum; //throw away variable + char *starpos = NULL; + + if(code_seen('G')) + { + switch((int)code_value()) + { + case 0: // G0 -> G1 + case 1: // G1 + if(Stopped == false) { + get_coordinates(); // For X Y Z E F + prepare_move(); + //ClearToSend(); + return; + } + //break; + case 2: // G2 - CW ARC + if(Stopped == false) { + get_arc_coordinates(); + prepare_arc_move(true); + return; + } + case 3: // G3 - CCW ARC + if(Stopped == false) { + get_arc_coordinates(); + prepare_arc_move(false); + return; + } + case 4: // G4 dwell + LCD_MESSAGEPGM(MSG_DWELL); + codenum = 0; + if(code_seen('P')) codenum = code_value(); // milliseconds to wait + if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait + + st_synchronize(); + codenum += millis(); // keep track of when we started waiting + previous_millis_cmd = millis(); + while(millis() < codenum ){ + manage_heater(); + manage_inactivity(); + lcd_update(); + } + break; + #ifdef FWRETRACT + case 10: // G10 retract + if(!retracted) + { + destination[X_AXIS]=current_position[X_AXIS]; + destination[Y_AXIS]=current_position[Y_AXIS]; + destination[Z_AXIS]=current_position[Z_AXIS]; + current_position[Z_AXIS]+=-retract_zlift; + destination[E_AXIS]=current_position[E_AXIS]-retract_length; + feedrate=retract_feedrate; + retracted=true; + prepare_move(); + } + + break; + case 11: // G10 retract_recover + if(!retracted) + { + destination[X_AXIS]=current_position[X_AXIS]; + destination[Y_AXIS]=current_position[Y_AXIS]; + destination[Z_AXIS]=current_position[Z_AXIS]; + + current_position[Z_AXIS]+=retract_zlift; + current_position[E_AXIS]+=-retract_recover_length; + feedrate=retract_recover_feedrate; + retracted=false; + prepare_move(); + } + break; + #endif //FWRETRACT + case 28: //G28 Home all Axis one at a time + saved_feedrate = feedrate; + saved_feedmultiply = feedmultiply; + feedmultiply = 100; + previous_millis_cmd = millis(); + + enable_endstops(true); + + for(int8_t i=0; i < NUM_AXIS; i++) { + destination[i] = current_position[i]; + } + feedrate = 0.0; + home_all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))); + + #if Z_HOME_DIR > 0 // If homing away from BED do Z first + if((home_all_axis) || (code_seen(axis_codes[Z_AXIS]))) { + HOMEAXIS(Z); + } + #endif + + #ifdef QUICK_HOME + if((home_all_axis)||( code_seen(axis_codes[X_AXIS]) && code_seen(axis_codes[Y_AXIS])) ) //first diagonal move + { + current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0; + + plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); + destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR; + feedrate = homing_feedrate[X_AXIS]; + if(homing_feedrate[Y_AXIS] 0){ + codenum += millis(); // keep track of when we started waiting + while(millis() < codenum && !LCD_CLICKED){ + manage_heater(); + manage_inactivity(); + lcd_update(); + } + }else{ + while(!LCD_CLICKED){ + manage_heater(); + manage_inactivity(); + lcd_update(); + } + } + LCD_MESSAGEPGM(MSG_RESUMING); + } + break; +#endif + case 17: + LCD_MESSAGEPGM(MSG_NO_MOVE); + enable_x(); + enable_y(); + enable_z(); + enable_e0(); + enable_e1(); + enable_e2(); + break; + +#ifdef SDSUPPORT + case 20: // M20 - list SD card + SERIAL_PROTOCOLLNPGM(MSG_BEGIN_FILE_LIST); + card.ls(); + SERIAL_PROTOCOLLNPGM(MSG_END_FILE_LIST); + break; + case 21: // M21 - init SD card + + card.initsd(); + + break; + case 22: //M22 - release SD card + card.release(); + + break; + case 23: //M23 - Select file + starpos = (strchr(strchr_pointer + 4,'*')); + if(starpos!=NULL) + *(starpos-1)='\0'; + card.openFile(strchr_pointer + 4,true); + break; + case 24: //M24 - Start SD print + card.startFileprint(); + starttime=millis(); + break; + case 25: //M25 - Pause SD print + card.pauseSDPrint(); + break; + case 26: //M26 - Set SD index + if(card.cardOK && code_seen('S')) { + card.setIndex(code_value_long()); + } + break; + case 27: //M27 - Get SD status + card.getStatus(); + break; + case 28: //M28 - Start SD write + starpos = (strchr(strchr_pointer + 4,'*')); + if(starpos != NULL){ + char* npos = strchr(cmdbuffer[bufindr], 'N'); + strchr_pointer = strchr(npos,' ') + 1; + *(starpos-1) = '\0'; + } + card.openFile(strchr_pointer+4,false); + break; + case 29: //M29 - Stop SD write + //processed in write to file routine above + //card,saving = false; + break; + case 30: //M30 Delete File + if (card.cardOK){ + card.closefile(); + starpos = (strchr(strchr_pointer + 4,'*')); + if(starpos != NULL){ + char* npos = strchr(cmdbuffer[bufindr], 'N'); + strchr_pointer = strchr(npos,' ') + 1; + *(starpos-1) = '\0'; + } + card.removeFile(strchr_pointer + 4); + } + break; + +#endif //SDSUPPORT + + case 31: //M31 take time since the start of the SD print or an M109 command + { + stoptime=millis(); + char time[30]; + unsigned long t=(stoptime-starttime)/1000; + int sec,min; + min=t/60; + sec=t%60; + sprintf_P(time, PSTR("%i min, %i sec"), min, sec); + SERIAL_ECHO_START; + SERIAL_ECHOLN(time); + lcd_setstatus(time); + autotempShutdown(); + } + break; + case 42: //M42 -Change pin status via gcode + if (code_seen('S')) + { + int pin_status = code_value(); + int pin_number = LED_PIN; + if (code_seen('P') && pin_status >= 0 && pin_status <= 255) + pin_number = code_value(); + for(int8_t i = 0; i < (int8_t)sizeof(sensitive_pins); i++) + { + if (sensitive_pins[i] == pin_number) + { + pin_number = -1; + break; + } + } + if (pin_number > -1) + { + pinMode(pin_number, OUTPUT); + digitalWrite(pin_number, pin_status); + analogWrite(pin_number, pin_status); + } + } + break; + case 104: // M104 + if(setTargetedHotend(104)){ + break; + } + if (code_seen('S')) setTargetHotend(code_value(), tmp_extruder); + setWatch(); + break; + case 140: // M140 set bed temp + if (code_seen('S')) setTargetBed(code_value()); + break; + case 105 : // M105 + if(setTargetedHotend(105)){ + break; + } + #if (TEMP_0_PIN > -1) + SERIAL_PROTOCOLPGM("ok T:"); + SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); + SERIAL_PROTOCOLPGM(" /"); + SERIAL_PROTOCOL_F(degTargetHotend(tmp_extruder),1); + #if TEMP_BED_PIN > -1 + SERIAL_PROTOCOLPGM(" B:"); + SERIAL_PROTOCOL_F(degBed(),1); + SERIAL_PROTOCOLPGM(" /"); + SERIAL_PROTOCOL_F(degTargetBed(),1); + #endif //TEMP_BED_PIN + #else + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM(MSG_ERR_NO_THERMISTORS); + #endif + + SERIAL_PROTOCOLPGM(" @:"); + SERIAL_PROTOCOL(getHeaterPower(tmp_extruder)); + + SERIAL_PROTOCOLPGM(" B@:"); + SERIAL_PROTOCOL(getHeaterPower(-1)); + + SERIAL_PROTOCOLLN(""); + return; + break; + case 109: + {// M109 - Wait for extruder heater to reach target. + if(setTargetedHotend(109)){ + break; + } + LCD_MESSAGEPGM(MSG_HEATING); + #ifdef AUTOTEMP + autotemp_enabled=false; + #endif + if (code_seen('S')) setTargetHotend(code_value(), tmp_extruder); + #ifdef AUTOTEMP + if (code_seen('S')) autotemp_min=code_value(); + if (code_seen('B')) autotemp_max=code_value(); + if (code_seen('F')) + { + autotemp_factor=code_value(); + autotemp_enabled=true; + } + #endif + + setWatch(); + codenum = millis(); + + /* See if we are heating up or cooling down */ + bool target_direction = isHeatingHotend(tmp_extruder); // true if heating, false if cooling + + #ifdef TEMP_RESIDENCY_TIME + long residencyStart; + residencyStart = -1; + /* continue to loop until we have reached the target temp + _and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */ + while((residencyStart == -1) || + (residencyStart >= 0 && (((unsigned int) (millis() - residencyStart)) < (TEMP_RESIDENCY_TIME * 1000UL))) ) { + #else + while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) { + #endif //TEMP_RESIDENCY_TIME + if( (millis() - codenum) > 1000UL ) + { //Print Temp Reading and remaining time every 1 second while heating up/cooling down + SERIAL_PROTOCOLPGM("T:"); + SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); + SERIAL_PROTOCOLPGM(" E:"); + SERIAL_PROTOCOL((int)tmp_extruder); + #ifdef TEMP_RESIDENCY_TIME + SERIAL_PROTOCOLPGM(" W:"); + if(residencyStart > -1) + { + codenum = ((TEMP_RESIDENCY_TIME * 1000UL) - (millis() - residencyStart)) / 1000UL; + SERIAL_PROTOCOLLN( codenum ); + } + else + { + SERIAL_PROTOCOLLN( "?" ); + } + #else + SERIAL_PROTOCOLLN(""); + #endif + codenum = millis(); + } + manage_heater(); + manage_inactivity(); + lcd_update(); + #ifdef TEMP_RESIDENCY_TIME + /* start/restart the TEMP_RESIDENCY_TIME timer whenever we reach target temp for the first time + or when current temp falls outside the hysteresis after target temp was reached */ + if ((residencyStart == -1 && target_direction && (degHotend(tmp_extruder) >= (degTargetHotend(tmp_extruder)-TEMP_WINDOW))) || + (residencyStart == -1 && !target_direction && (degHotend(tmp_extruder) <= (degTargetHotend(tmp_extruder)+TEMP_WINDOW))) || + (residencyStart > -1 && labs(degHotend(tmp_extruder) - degTargetHotend(tmp_extruder)) > TEMP_HYSTERESIS) ) + { + residencyStart = millis(); + } + #endif //TEMP_RESIDENCY_TIME + } + LCD_MESSAGEPGM(MSG_HEATING_COMPLETE); + starttime=millis(); + previous_millis_cmd = millis(); + } + break; + case 190: // M190 - Wait for bed heater to reach target. + #if TEMP_BED_PIN > -1 + LCD_MESSAGEPGM(MSG_BED_HEATING); + if (code_seen('S')) setTargetBed(code_value()); + codenum = millis(); + while(isHeatingBed()) + { + if(( millis() - codenum) > 1000 ) //Print Temp Reading every 1 second while heating up. + { + float tt=degHotend(active_extruder); + SERIAL_PROTOCOLPGM("T:"); + SERIAL_PROTOCOL(tt); + SERIAL_PROTOCOLPGM(" E:"); + SERIAL_PROTOCOL((int)active_extruder); + SERIAL_PROTOCOLPGM(" B:"); + SERIAL_PROTOCOL_F(degBed(),1); + SERIAL_PROTOCOLLN(""); + codenum = millis(); + } + manage_heater(); + manage_inactivity(); + lcd_update(); + } + LCD_MESSAGEPGM(MSG_BED_DONE); + previous_millis_cmd = millis(); + #endif + break; + + #if FAN_PIN > -1 + case 106: //M106 Fan On + if (code_seen('S')){ + fanSpeed=constrain(code_value(),0,255); + } + else { + fanSpeed=255; + } + break; + case 107: //M107 Fan Off + fanSpeed = 0; + break; + #endif //FAN_PIN + + #if (PS_ON_PIN > -1) + case 80: // M80 - ATX Power On + SET_OUTPUT(PS_ON_PIN); //GND + WRITE(PS_ON_PIN, PS_ON_AWAKE); + break; + #endif + + case 81: // M81 - ATX Power Off + + #if defined SUICIDE_PIN && SUICIDE_PIN > -1 + st_synchronize(); + suicide(); + #elif (PS_ON_PIN > -1) + SET_OUTPUT(PS_ON_PIN); + WRITE(PS_ON_PIN, PS_ON_ASLEEP); + #endif + break; + + case 82: + axis_relative_modes[3] = false; + break; + case 83: + axis_relative_modes[3] = true; + break; + case 18: //compatibility + case 84: // M84 + if(code_seen('S')){ + stepper_inactive_time = code_value() * 1000; + } + else + { + bool all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))|| (code_seen(axis_codes[3]))); + if(all_axis) + { + st_synchronize(); + disable_e0(); + disable_e1(); + disable_e2(); + finishAndDisableSteppers(); + } + else + { + st_synchronize(); + if(code_seen('X')) disable_x(); + if(code_seen('Y')) disable_y(); + if(code_seen('Z')) disable_z(); + #if ((E0_ENABLE_PIN != X_ENABLE_PIN) && (E1_ENABLE_PIN != Y_ENABLE_PIN)) // Only enable on boards that have seperate ENABLE_PINS + if(code_seen('E')) { + disable_e0(); + disable_e1(); + disable_e2(); + } + #endif + } + } + break; + case 85: // M85 + code_seen('S'); + max_inactive_time = code_value() * 1000; + break; + case 92: // M92 + for(int8_t i=0; i < NUM_AXIS; i++) + { + if(code_seen(axis_codes[i])) + { + if(i == 3) { // E + float value = code_value(); + if(value < 20.0) { + float factor = axis_steps_per_unit[i] / value; // increase e constants if M92 E14 is given for netfab. + max_e_jerk *= factor; + max_feedrate[i] *= factor; + axis_steps_per_sqr_second[i] *= factor; + } + axis_steps_per_unit[i] = value; + } + else { + axis_steps_per_unit[i] = code_value(); + } + } + } + break; + case 115: // M115 + SERIAL_PROTOCOLPGM(MSG_M115_REPORT); + break; + case 117: // M117 display message + starpos = (strchr(strchr_pointer + 5,'*')); + if(starpos!=NULL) + *(starpos-1)='\0'; + lcd_setstatus(strchr_pointer + 5); + break; + case 114: // M114 + SERIAL_PROTOCOLPGM("X:"); + SERIAL_PROTOCOL(current_position[X_AXIS]); + SERIAL_PROTOCOLPGM("Y:"); + SERIAL_PROTOCOL(current_position[Y_AXIS]); + SERIAL_PROTOCOLPGM("Z:"); + SERIAL_PROTOCOL(current_position[Z_AXIS]); + SERIAL_PROTOCOLPGM("E:"); + SERIAL_PROTOCOL(current_position[E_AXIS]); + + SERIAL_PROTOCOLPGM(MSG_COUNT_X); + SERIAL_PROTOCOL(float(st_get_position(X_AXIS))/axis_steps_per_unit[X_AXIS]); + SERIAL_PROTOCOLPGM("Y:"); + SERIAL_PROTOCOL(float(st_get_position(Y_AXIS))/axis_steps_per_unit[Y_AXIS]); + SERIAL_PROTOCOLPGM("Z:"); + SERIAL_PROTOCOL(float(st_get_position(Z_AXIS))/axis_steps_per_unit[Z_AXIS]); + + SERIAL_PROTOCOLLN(""); + break; + case 120: // M120 + enable_endstops(false) ; + break; + case 121: // M121 + enable_endstops(true) ; + break; + case 119: // M119 + SERIAL_PROTOCOLLN(MSG_M119_REPORT); + #if (X_MIN_PIN > -1) + SERIAL_PROTOCOLPGM(MSG_X_MIN); + SERIAL_PROTOCOLLN(((READ(X_MIN_PIN)^X_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); + #endif + #if (X_MAX_PIN > -1) + SERIAL_PROTOCOLPGM(MSG_X_MAX); + SERIAL_PROTOCOLLN(((READ(X_MAX_PIN)^X_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); + #endif + #if (Y_MIN_PIN > -1) + SERIAL_PROTOCOLPGM(MSG_Y_MIN); + SERIAL_PROTOCOLLN(((READ(Y_MIN_PIN)^Y_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); + #endif + #if (Y_MAX_PIN > -1) + SERIAL_PROTOCOLPGM(MSG_Y_MAX); + SERIAL_PROTOCOLLN(((READ(Y_MAX_PIN)^Y_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); + #endif + #if (Z_MIN_PIN > -1) + SERIAL_PROTOCOLPGM(MSG_Z_MIN); + SERIAL_PROTOCOLLN(((READ(Z_MIN_PIN)^Z_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); + #endif + #if (Z_MAX_PIN > -1) + SERIAL_PROTOCOLPGM(MSG_Z_MAX); + SERIAL_PROTOCOLLN(((READ(Z_MAX_PIN)^Z_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); + #endif + break; + //TODO: update for all axis, use for loop + case 201: // M201 + for(int8_t i=0; i < NUM_AXIS; i++) + { + if(code_seen(axis_codes[i])) + { + max_acceleration_units_per_sq_second[i] = code_value(); + axis_steps_per_sqr_second[i] = code_value() * axis_steps_per_unit[i]; + } + } + break; + #if 0 // Not used for Sprinter/grbl gen6 + case 202: // M202 + for(int8_t i=0; i < NUM_AXIS; i++) { + if(code_seen(axis_codes[i])) axis_travel_steps_per_sqr_second[i] = code_value() * axis_steps_per_unit[i]; + } + break; + #endif + case 203: // M203 max feedrate mm/sec + for(int8_t i=0; i < NUM_AXIS; i++) { + if(code_seen(axis_codes[i])) max_feedrate[i] = code_value(); + } + break; + case 204: // M204 acclereration S normal moves T filmanent only moves + { + if(code_seen('S')) acceleration = code_value() ; + if(code_seen('T')) retract_acceleration = code_value() ; + } + break; + case 205: //M205 advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk + { + if(code_seen('S')) minimumfeedrate = code_value(); + if(code_seen('T')) mintravelfeedrate = code_value(); + if(code_seen('B')) minsegmenttime = code_value() ; + if(code_seen('X')) max_xy_jerk = code_value() ; + if(code_seen('Z')) max_z_jerk = code_value() ; + if(code_seen('E')) max_e_jerk = code_value() ; + } + break; + case 206: // M206 additional homeing offset + for(int8_t i=0; i < 3; i++) + { + if(code_seen(axis_codes[i])) add_homeing[i] = code_value(); + } + break; + #ifdef FWRETRACT + case 207: //M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop] + { + if(code_seen('S')) + { + retract_length = code_value() ; + } + if(code_seen('F')) + { + retract_feedrate = code_value() ; + } + if(code_seen('Z')) + { + retract_zlift = code_value() ; + } + }break; + case 208: // M208 - set retract recover length S[positive mm surplus to the M207 S*] F[feedrate mm/sec] + { + if(code_seen('S')) + { + retract_recover_length = code_value() ; + } + if(code_seen('F')) + { + retract_recover_feedrate = code_value() ; + } + }break; + case 209: // M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. + { + if(code_seen('S')) + { + int t= code_value() ; + switch(t) + { + case 0: autoretract_enabled=false;retracted=false;break; + case 1: autoretract_enabled=true;retracted=false;break; + default: + SERIAL_ECHO_START; + SERIAL_ECHOPGM(MSG_UNKNOWN_COMMAND); + SERIAL_ECHO(cmdbuffer[bufindr]); + SERIAL_ECHOLNPGM("\""); + } + } + + }break; + #endif // FWRETRACT + #if EXTRUDERS > 1 + case 218: // M218 - set hotend offset (in mm), T X Y + { + if(setTargetedHotend(218)){ + break; + } + if(code_seen('X')) + { + extruder_offset[X_AXIS][tmp_extruder] = code_value(); + } + if(code_seen('Y')) + { + extruder_offset[Y_AXIS][tmp_extruder] = code_value(); + } + SERIAL_ECHO_START; + SERIAL_ECHOPGM(MSG_HOTEND_OFFSET); + for(tmp_extruder = 0; tmp_extruder < EXTRUDERS; tmp_extruder++) + { + SERIAL_ECHO(" "); + SERIAL_ECHO(extruder_offset[X_AXIS][tmp_extruder]); + SERIAL_ECHO(","); + SERIAL_ECHO(extruder_offset[Y_AXIS][tmp_extruder]); + } + SERIAL_ECHOLN(""); + }break; + #endif + case 220: // M220 S- set speed factor override percentage + { + if(code_seen('S')) + { + feedmultiply = code_value() ; + } + } + break; + case 221: // M221 S- set extrude factor override percentage + { + if(code_seen('S')) + { + extrudemultiply = code_value() ; + } + } + break; + + #ifdef PIDTEMP + case 301: // M301 + { + if(code_seen('P')) Kp = code_value(); + if(code_seen('I')) Ki = code_value()*PID_dT; + if(code_seen('D')) Kd = code_value()/PID_dT; + #ifdef PID_ADD_EXTRUSION_RATE + if(code_seen('C')) Kc = code_value(); + #endif + updatePID(); + SERIAL_PROTOCOL(MSG_OK); + SERIAL_PROTOCOL(" p:"); + SERIAL_PROTOCOL(Kp); + SERIAL_PROTOCOL(" i:"); + SERIAL_PROTOCOL(Ki/PID_dT); + SERIAL_PROTOCOL(" d:"); + SERIAL_PROTOCOL(Kd*PID_dT); + #ifdef PID_ADD_EXTRUSION_RATE + SERIAL_PROTOCOL(" c:"); + SERIAL_PROTOCOL(Kc*PID_dT); + #endif + SERIAL_PROTOCOLLN(""); + } + break; + #endif //PIDTEMP + #ifdef PIDTEMPBED + case 304: // M304 + { + if(code_seen('P')) bedKp = code_value(); + if(code_seen('I')) bedKi = code_value()*PID_dT; + if(code_seen('D')) bedKd = code_value()/PID_dT; + updatePID(); + SERIAL_PROTOCOL(MSG_OK); + SERIAL_PROTOCOL(" p:"); + SERIAL_PROTOCOL(bedKp); + SERIAL_PROTOCOL(" i:"); + SERIAL_PROTOCOL(bedKi/PID_dT); + SERIAL_PROTOCOL(" d:"); + SERIAL_PROTOCOL(bedKd*PID_dT); + SERIAL_PROTOCOLLN(""); + } + break; + #endif //PIDTEMP + case 240: // M240 Triggers a camera by emulating a Canon RC-1 : http://www.doc-diy.net/photo/rc-1_hacked/ + { + #ifdef PHOTOGRAPH_PIN + #if (PHOTOGRAPH_PIN > -1) + const uint8_t NUM_PULSES=16; + const float PULSE_LENGTH=0.01524; + for(int i=0; i < NUM_PULSES; i++) { + WRITE(PHOTOGRAPH_PIN, HIGH); + _delay_ms(PULSE_LENGTH); + WRITE(PHOTOGRAPH_PIN, LOW); + _delay_ms(PULSE_LENGTH); + } + delay(7.33); + for(int i=0; i < NUM_PULSES; i++) { + WRITE(PHOTOGRAPH_PIN, HIGH); + _delay_ms(PULSE_LENGTH); + WRITE(PHOTOGRAPH_PIN, LOW); + _delay_ms(PULSE_LENGTH); + } + #endif + #endif + } + break; + + case 302: // allow cold extrudes + { + allow_cold_extrudes(true); + } + break; + case 303: // M303 PID autotune + { + float temp = 150.0; + int e=0; + int c=5; + if (code_seen('E')) e=code_value(); + if (e<0) + temp=70; + if (code_seen('S')) temp=code_value(); + if (code_seen('C')) c=code_value(); + PID_autotune(temp, e, c); + } + break; + case 400: // M400 finish all moves + { + st_synchronize(); + } + break; + case 500: // M500 Store settings in EEPROM + { + Config_StoreSettings(); + } + break; + case 501: // M501 Read settings from EEPROM + { + Config_RetrieveSettings(); + } + break; + case 502: // M502 Revert to default settings + { + Config_ResetDefault(); + } + break; + case 503: // M503 print settings currently in memory + { + Config_PrintSettings(); + } + break; + #ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED + case 540: + { + if(code_seen('S')) abort_on_endstop_hit = code_value() > 0; + } + break; + #endif + #ifdef FILAMENTCHANGEENABLE + case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] + { + float target[4]; + float lastpos[4]; + target[X_AXIS]=current_position[X_AXIS]; + target[Y_AXIS]=current_position[Y_AXIS]; + target[Z_AXIS]=current_position[Z_AXIS]; + target[E_AXIS]=current_position[E_AXIS]; + lastpos[X_AXIS]=current_position[X_AXIS]; + lastpos[Y_AXIS]=current_position[Y_AXIS]; + lastpos[Z_AXIS]=current_position[Z_AXIS]; + lastpos[E_AXIS]=current_position[E_AXIS]; + //retract by E + if(code_seen('E')) + { + target[E_AXIS]+= code_value(); + } + else + { + #ifdef FILAMENTCHANGE_FIRSTRETRACT + target[E_AXIS]+= FILAMENTCHANGE_FIRSTRETRACT ; + #endif + } + plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); + + //lift Z + if(code_seen('Z')) + { + target[Z_AXIS]+= code_value(); + } + else + { + #ifdef FILAMENTCHANGE_ZADD + target[Z_AXIS]+= FILAMENTCHANGE_ZADD ; + #endif + } + plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); + + //move xy + if(code_seen('X')) + { + target[X_AXIS]+= code_value(); + } + else + { + #ifdef FILAMENTCHANGE_XPOS + target[X_AXIS]= FILAMENTCHANGE_XPOS ; + #endif + } + if(code_seen('Y')) + { + target[Y_AXIS]= code_value(); + } + else + { + #ifdef FILAMENTCHANGE_YPOS + target[Y_AXIS]= FILAMENTCHANGE_YPOS ; + #endif + } + + plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); + + if(code_seen('L')) + { + target[E_AXIS]+= code_value(); + } + else + { + #ifdef FILAMENTCHANGE_FINALRETRACT + target[E_AXIS]+= FILAMENTCHANGE_FINALRETRACT ; + #endif + } + + plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); + + //finish moves + st_synchronize(); + //disable extruder steppers so filament can be removed + disable_e0(); + disable_e1(); + disable_e2(); + delay(100); + LCD_ALERTMESSAGEPGM(MSG_FILAMENTCHANGE); + uint8_t cnt=0; + while(!LCD_CLICKED){ + cnt++; + manage_heater(); + manage_inactivity(); + lcd_update(); + + #if BEEPER > -1 + if(cnt==0) + { + SET_OUTPUT(BEEPER); + + WRITE(BEEPER,HIGH); + delay(3); + WRITE(BEEPER,LOW); + delay(3); + } + #endif + } + + //return to normal + if(code_seen('L')) + { + target[E_AXIS]+= -code_value(); + } + else + { + #ifdef FILAMENTCHANGE_FINALRETRACT + target[E_AXIS]+=(-1)*FILAMENTCHANGE_FINALRETRACT ; + #endif + } + current_position[E_AXIS]=target[E_AXIS]; //the long retract of L is compensated by manual filament feeding + plan_set_e_position(current_position[E_AXIS]); + plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); //should do nothing + plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); //move xy back + plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], lastpos[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); //move z back + plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], lastpos[Z_AXIS], lastpos[E_AXIS], feedrate/60, active_extruder); //final untretract + } + break; + #endif //FILAMENTCHANGEENABLE + case 907: // M907 Set digital trimpot motor current using axis codes. + { + #if DIGIPOTSS_PIN > -1 + for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) digipot_current(i,code_value()); + if(code_seen('B')) digipot_current(4,code_value()); + if(code_seen('S')) for(int i=0;i<=4;i++) digipot_current(i,code_value()); + #endif + } + case 908: // M908 Control digital trimpot directly. + { + #if DIGIPOTSS_PIN > -1 + uint8_t channel,current; + if(code_seen('P')) channel=code_value(); + if(code_seen('S')) current=code_value(); + digitalPotWrite(channel, current); + #endif + } + break; + case 350: // M350 Set microstepping mode. Warning: Steps per unit remains unchanged. S code sets stepping mode for all drivers. + { + #if X_MS1_PIN > -1 + if(code_seen('S')) for(int i=0;i<=4;i++) microstep_mode(i,code_value()); + for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) microstep_mode(i,(uint8_t)code_value()); + if(code_seen('B')) microstep_mode(4,code_value()); + microstep_readings(); + #endif + } + break; + case 351: // M351 Toggle MS1 MS2 pins directly, S# determines MS1 or MS2, X# sets the pin high/low. + { + #if X_MS1_PIN > -1 + if(code_seen('S')) switch((int)code_value()) + { + case 1: + for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) microstep_ms(i,code_value(),-1); + if(code_seen('B')) microstep_ms(4,code_value(),-1); + break; + case 2: + for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) microstep_ms(i,-1,code_value()); + if(code_seen('B')) microstep_ms(4,-1,code_value()); + break; + } + microstep_readings(); + #endif + } + break; + case 999: // M999: Restart after being stopped + Stopped = false; + lcd_reset_alert_level(); + gcode_LastN = Stopped_gcode_LastN; + FlushSerialRequestResend(); + break; + } + } + + else if(code_seen('T')) + { + tmp_extruder = code_value(); + if(tmp_extruder >= EXTRUDERS) { + SERIAL_ECHO_START; + SERIAL_ECHO("T"); + SERIAL_ECHO(tmp_extruder); + SERIAL_ECHOLN(MSG_INVALID_EXTRUDER); + } + else { + boolean make_move = false; + if(code_seen('F')) { + make_move = true; + next_feedrate = code_value(); + if(next_feedrate > 0.0) { + feedrate = next_feedrate; + } + } + #if EXTRUDERS > 1 + if(tmp_extruder != active_extruder) { + // Save current position to return to after applying extruder offset + memcpy(destination, current_position, sizeof(destination)); + // Offset extruder (only by XY) + int i; + for(i = 0; i < 2; i++) { + current_position[i] = current_position[i] - + extruder_offset[i][active_extruder] + + extruder_offset[i][tmp_extruder]; + } + // Set the new active extruder and position + active_extruder = tmp_extruder; + plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); + // Move to the old position if 'F' was in the parameters + if(make_move && Stopped == false) { + prepare_move(); + } + } + #endif + SERIAL_ECHO_START; + SERIAL_ECHO(MSG_ACTIVE_EXTRUDER); + SERIAL_PROTOCOLLN((int)active_extruder); + } + } + + else + { + SERIAL_ECHO_START; + SERIAL_ECHOPGM(MSG_UNKNOWN_COMMAND); + SERIAL_ECHO(cmdbuffer[bufindr]); + SERIAL_ECHOLNPGM("\""); + } + + ClearToSend(); +} + +void FlushSerialRequestResend() +{ + //char cmdbuffer[bufindr][100]="Resend:"; + MYSERIAL.flush(); + SERIAL_PROTOCOLPGM(MSG_RESEND); + SERIAL_PROTOCOLLN(gcode_LastN + 1); + ClearToSend(); +} + +void ClearToSend() +{ + previous_millis_cmd = millis(); + #ifdef SDSUPPORT + if(fromsd[bufindr]) + return; + #endif //SDSUPPORT + SERIAL_PROTOCOLLNPGM(MSG_OK); +} + +void get_coordinates() +{ + bool seen[4]={false,false,false,false}; + for(int8_t i=0; i < NUM_AXIS; i++) { + if(code_seen(axis_codes[i])) + { + destination[i] = (float)code_value() + (axis_relative_modes[i] || relative_mode)*current_position[i]; + seen[i]=true; + } + else destination[i] = current_position[i]; //Are these else lines really needed? + } + if(code_seen('F')) { + next_feedrate = code_value(); + if(next_feedrate > 0.0) feedrate = next_feedrate; + } + #ifdef FWRETRACT + if(autoretract_enabled) + if( !(seen[X_AXIS] || seen[Y_AXIS] || seen[Z_AXIS]) && seen[E_AXIS]) + { + float echange=destination[E_AXIS]-current_position[E_AXIS]; + if(echange<-MIN_RETRACT) //retract + { + if(!retracted) + { + + destination[Z_AXIS]+=retract_zlift; //not sure why chaninging current_position negatively does not work. + //if slicer retracted by echange=-1mm and you want to retract 3mm, corrrectede=-2mm additionally + float correctede=-echange-retract_length; + //to generate the additional steps, not the destination is changed, but inversely the current position + current_position[E_AXIS]+=-correctede; + feedrate=retract_feedrate; + retracted=true; + } + + } + else + if(echange>MIN_RETRACT) //retract_recover + { + if(retracted) + { + //current_position[Z_AXIS]+=-retract_zlift; + //if slicer retracted_recovered by echange=+1mm and you want to retract_recover 3mm, corrrectede=2mm additionally + float correctede=-echange+1*retract_length+retract_recover_length; //total unretract=retract_length+retract_recover_length[surplus] + current_position[E_AXIS]+=correctede; //to generate the additional steps, not the destination is changed, but inversely the current position + feedrate=retract_recover_feedrate; + retracted=false; + } + } + + } + #endif //FWRETRACT +} + +void get_arc_coordinates() +{ +#ifdef SF_ARC_FIX + bool relative_mode_backup = relative_mode; + relative_mode = true; +#endif + get_coordinates(); +#ifdef SF_ARC_FIX + relative_mode=relative_mode_backup; +#endif + + if(code_seen('I')) { + offset[0] = code_value(); + } + else { + offset[0] = 0.0; + } + if(code_seen('J')) { + offset[1] = code_value(); + } + else { + offset[1] = 0.0; + } +} + +void clamp_to_software_endstops(float target[3]) +{ + if (min_software_endstops) { + if (target[X_AXIS] < min_pos[X_AXIS]) target[X_AXIS] = min_pos[X_AXIS]; + if (target[Y_AXIS] < min_pos[Y_AXIS]) target[Y_AXIS] = min_pos[Y_AXIS]; + if (target[Z_AXIS] < min_pos[Z_AXIS]) target[Z_AXIS] = min_pos[Z_AXIS]; + } + + if (max_software_endstops) { + if (target[X_AXIS] > max_pos[X_AXIS]) target[X_AXIS] = max_pos[X_AXIS]; + if (target[Y_AXIS] > max_pos[Y_AXIS]) target[Y_AXIS] = max_pos[Y_AXIS]; + if (target[Z_AXIS] > max_pos[Z_AXIS]) target[Z_AXIS] = max_pos[Z_AXIS]; + } +} + +void prepare_move() +{ + clamp_to_software_endstops(destination); + + previous_millis_cmd = millis(); + // Do not use feedmultiply for E or Z only moves + if( (current_position[X_AXIS] == destination [X_AXIS]) && (current_position[Y_AXIS] == destination [Y_AXIS])) { + plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); + } + else { + plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate*feedmultiply/60/100.0, active_extruder); + } + for(int8_t i=0; i < NUM_AXIS; i++) { + current_position[i] = destination[i]; + } +} + +void prepare_arc_move(char isclockwise) { + float r = hypot(offset[X_AXIS], offset[Y_AXIS]); // Compute arc radius for mc_arc + + // Trace the arc + mc_arc(current_position, destination, offset, X_AXIS, Y_AXIS, Z_AXIS, feedrate*feedmultiply/60/100.0, r, isclockwise, active_extruder); + + // As far as the parser is concerned, the position is now == target. In reality the + // motion control system might still be processing the action and the real tool position + // in any intermediate location. + for(int8_t i=0; i < NUM_AXIS; i++) { + current_position[i] = destination[i]; + } + previous_millis_cmd = millis(); +} + +#ifdef CONTROLLERFAN_PIN +unsigned long lastMotor = 0; //Save the time for when a motor was turned on last +unsigned long lastMotorCheck = 0; + +void controllerFan() +{ + if ((millis() - lastMotorCheck) >= 2500) //Not a time critical function, so we only check every 2500ms + { + lastMotorCheck = millis(); + + if(!READ(X_ENABLE_PIN) || !READ(Y_ENABLE_PIN) || !READ(Z_ENABLE_PIN) + #if EXTRUDERS > 2 + || !READ(E2_ENABLE_PIN) + #endif + #if EXTRUDER > 1 + || !READ(E2_ENABLE_PIN) + #endif + || !READ(E0_ENABLE_PIN)) //If any of the drivers are enabled... + { + lastMotor = millis(); //... set time to NOW so the fan will turn on + } + + if ((millis() - lastMotor) >= (CONTROLLERFAN_SEC*1000UL) || lastMotor == 0) //If the last time any driver was enabled, is longer since than CONTROLLERSEC... + { + WRITE(CONTROLLERFAN_PIN, LOW); //... turn the fan off + } + else + { + WRITE(CONTROLLERFAN_PIN, HIGH); //... turn the fan on + } + } +} +#endif + +#ifdef EXTRUDERFAN_PIN +unsigned long lastExtruderCheck = 0; + +void extruderFan() +{ + if ((millis() - lastExtruderCheck) >= 2500) //Not a time critical function, so we only check every 2500ms + { + lastExtruderCheck = millis(); + + if (degHotend(active_extruder) < EXTRUDERFAN_DEC) + { + WRITE(EXTRUDERFAN_PIN, LOW); //... turn the fan off + } + else + { + WRITE(EXTRUDERFAN_PIN, HIGH); //... turn the fan on + } + } +} +#endif + +void manage_inactivity() +{ + if( (millis() - previous_millis_cmd) > max_inactive_time ) + if(max_inactive_time) + kill(); + if(stepper_inactive_time) { + if( (millis() - previous_millis_cmd) > stepper_inactive_time ) + { + if(blocks_queued() == false) { + disable_x(); + disable_y(); + disable_z(); + disable_e0(); + disable_e1(); + disable_e2(); + } + } + } + #if( KILL_PIN>-1 ) + if( 0 == READ(KILL_PIN) ) + kill(); + #endif + #ifdef CONTROLLERFAN_PIN + controllerFan(); //Check if fan should be turned on to cool stepper drivers down + #endif + #ifdef EXTRUDER_RUNOUT_PREVENT + if( (millis() - previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 ) + if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP) + { + bool oldstatus=READ(E0_ENABLE_PIN); + enable_e0(); + float oldepos=current_position[E_AXIS]; + float oldedes=destination[E_AXIS]; + plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], + current_position[E_AXIS]+EXTRUDER_RUNOUT_EXTRUDE*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS], + EXTRUDER_RUNOUT_SPEED/60.*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS], active_extruder); + current_position[E_AXIS]=oldepos; + destination[E_AXIS]=oldedes; + plan_set_e_position(oldepos); + previous_millis_cmd=millis(); + st_synchronize(); + WRITE(E0_ENABLE_PIN,oldstatus); + } + #endif + check_axes_activity(); +} + +void kill() +{ + cli(); // Stop interrupts + disable_heater(); + + disable_x(); + disable_y(); + disable_z(); + disable_e0(); + disable_e1(); + disable_e2(); + + if(PS_ON_PIN > -1) pinMode(PS_ON_PIN,INPUT); + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM(MSG_ERR_KILLED); + LCD_ALERTMESSAGEPGM(MSG_KILLED); + suicide(); + while(1) { /* Intentionally left empty */ } // Wait for reset +} + +void Stop() +{ + disable_heater(); + if(Stopped == false) { + Stopped = true; + Stopped_gcode_LastN = gcode_LastN; // Save last g_code for restart + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM(MSG_ERR_STOPPED); + LCD_MESSAGEPGM(MSG_STOPPED); + } +} + +bool IsStopped() { return Stopped; }; + +#ifdef FAST_PWM_FAN +void setPwmFrequency(uint8_t pin, int val) +{ + val &= 0x07; + switch(digitalPinToTimer(pin)) + { + + #if defined(TCCR0A) + case TIMER0A: + case TIMER0B: +// TCCR0B &= ~(_BV(CS00) | _BV(CS01) | _BV(CS02)); +// TCCR0B |= val; + break; + #endif + + #if defined(TCCR1A) + case TIMER1A: + case TIMER1B: +// TCCR1B &= ~(_BV(CS10) | _BV(CS11) | _BV(CS12)); +// TCCR1B |= val; + break; + #endif + + #if defined(TCCR2) + case TIMER2: + case TIMER2: + TCCR2 &= ~(_BV(CS10) | _BV(CS11) | _BV(CS12)); + TCCR2 |= val; + break; + #endif + + #if defined(TCCR2A) + case TIMER2A: + case TIMER2B: + TCCR2B &= ~(_BV(CS20) | _BV(CS21) | _BV(CS22)); + TCCR2B |= val; + break; + #endif + + #if defined(TCCR3A) + case TIMER3A: + case TIMER3B: + case TIMER3C: + TCCR3B &= ~(_BV(CS30) | _BV(CS31) | _BV(CS32)); + TCCR3B |= val; + break; + #endif + + #if defined(TCCR4A) + case TIMER4A: + case TIMER4B: + case TIMER4C: + TCCR4B &= ~(_BV(CS40) | _BV(CS41) | _BV(CS42)); + TCCR4B |= val; + break; + #endif + + #if defined(TCCR5A) + case TIMER5A: + case TIMER5B: + case TIMER5C: + TCCR5B &= ~(_BV(CS50) | _BV(CS51) | _BV(CS52)); + TCCR5B |= val; + break; + #endif + + } +} +#endif //FAST_PWM_FAN + +bool setTargetedHotend(int code){ + tmp_extruder = active_extruder; + if(code_seen('T')) { + tmp_extruder = code_value(); + if(tmp_extruder >= EXTRUDERS) { + SERIAL_ECHO_START; + switch(code){ + case 104: + SERIAL_ECHO(MSG_M104_INVALID_EXTRUDER); + break; + case 105: + SERIAL_ECHO(MSG_M105_INVALID_EXTRUDER); + break; + case 109: + SERIAL_ECHO(MSG_M109_INVALID_EXTRUDER); + break; + case 218: + SERIAL_ECHO(MSG_M218_INVALID_EXTRUDER); + break; + } + SERIAL_ECHOLN(tmp_extruder); + return true; + } + } + return false; } From fd5b7e0cec6f03a744876ebd48b0845072fc3564 Mon Sep 17 00:00:00 2001 From: whosawhatsis Date: Fri, 22 Mar 2013 18:16:26 -0700 Subject: [PATCH 8/8] Separate PID_MAX from BANG_MAX This allows PID_FUNCTIONAL_RANGE to use a maximum duty cycle higher than PID_MAX. This is useful for powerful heaters to heat quickly in bang-bang mode, but use a lower duty cycle that is easier to stabilize in PID mode. --- Marlin/Configuration.h | 3 ++- Marlin/temperature.cpp | 4 ++-- 2 files changed, 4 insertions(+), 3 deletions(-) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 8031272db..601920088 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -117,7 +117,8 @@ // PID settings: // Comment the following line to disable PID and enable bang-bang. #define PIDTEMP -#define PID_MAX 256 // limits current to nozzle; 256=full current +#define BANG_MAX 256 // limits current to nozzle while in bang-bang mode; 256=full current +#define PID_MAX 256 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 256=full current #ifdef PIDTEMP //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index 6093c9934..58c7b60e6 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -325,10 +325,10 @@ void manage_heater() #ifndef PID_OPENLOOP pid_error[e] = target_temperature[e] - pid_input; if(pid_error[e] > PID_FUNCTIONAL_RANGE) { - pid_output = PID_MAX; + pid_output = BANG_MAX; pid_reset[e] = true; } - else if(pid_error[e] < -PID_FUNCTIONAL_RANGE) { + else if(pid_error[e] < -PID_FUNCTIONAL_RANGE || target_temperature[e] == 0) { pid_output = 0; pid_reset[e] = true; }