80 lines
2.4 KiB
C++
80 lines
2.4 KiB
C++
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
#include "MarlinConfig.h"
|
|
|
|
#if ENABLED(DIGIPOT_I2C) && DISABLED(DIGIPOT_MCP4018)
|
|
|
|
#include "Stream.h"
|
|
#include "utility/twi.h"
|
|
#include "Wire.h"
|
|
|
|
// Settings for the I2C based DIGIPOT (MCP4451) on Azteeg X3 Pro
|
|
#if MB(5DPRINT)
|
|
#define DIGIPOT_I2C_FACTOR 117.96
|
|
#define DIGIPOT_I2C_MAX_CURRENT 1.736
|
|
#else
|
|
#define DIGIPOT_I2C_FACTOR 106.7
|
|
#define DIGIPOT_I2C_MAX_CURRENT 2.5
|
|
#endif
|
|
|
|
static byte current_to_wiper(float current) {
|
|
return byte(ceil(float((DIGIPOT_I2C_FACTOR * current))));
|
|
}
|
|
|
|
static void i2c_send(byte addr, byte a, byte b) {
|
|
Wire.beginTransmission(addr);
|
|
Wire.write(a);
|
|
Wire.write(b);
|
|
Wire.endTransmission();
|
|
}
|
|
|
|
// This is for the MCP4451 I2C based digipot
|
|
void digipot_i2c_set_current(int channel, float current) {
|
|
current = min((float) max(current, 0.0f), DIGIPOT_I2C_MAX_CURRENT);
|
|
// these addresses are specific to Azteeg X3 Pro, can be set to others,
|
|
// In this case first digipot is at address A0=0, A1= 0, second one is at A0=0, A1= 1
|
|
byte addr = 0x2C; // channel 0-3
|
|
if (channel >= 4) {
|
|
addr = 0x2E; // channel 4-7
|
|
channel -= 4;
|
|
}
|
|
|
|
// Initial setup
|
|
i2c_send(addr, 0x40, 0xff);
|
|
i2c_send(addr, 0xA0, 0xff);
|
|
|
|
// Set actual wiper value
|
|
byte addresses[4] = { 0x00, 0x10, 0x60, 0x70 };
|
|
i2c_send(addr, addresses[channel], current_to_wiper(current));
|
|
}
|
|
|
|
void digipot_i2c_init() {
|
|
const float digipot_motor_current[] = DIGIPOT_I2C_MOTOR_CURRENTS;
|
|
Wire.begin();
|
|
// setup initial currents as defined in Configuration_adv.h
|
|
for (int i = 0; i < COUNT(digipot_motor_current); i++)
|
|
digipot_i2c_set_current(i, digipot_motor_current[i]);
|
|
}
|
|
|
|
#endif //DIGIPOT_I2C
|